GPMC updates:
 - bugfixes: wrong/missing flags, omitted write, wrong test
 - don't map memory segments starting at zero
 - improve debug messaging
 - export gpmc_get_fclk_perio]d() since it's needed to calc timings
 - expect gpmc_cs_set_timings() caller to have initialized sync vs async

Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change the LCD mux setting from enable() to init() for PM
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some OMAP 24xx pin mux declarations to support:

 - TUSB 6010 EVM (on H4)
 - All three full speed USB ports
 - GPIOs used with USB0 on Apollon and H4

For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove some conflicting declarations in omap2/memory.c so that the
file builds again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some GPIO debug support:  /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.

Includes minor bugfixes:  recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update the Amstrad Delta defconfig to take advantage of the drivers that
have been added to the tree since the initial config.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In previous GPMC patch, there was a typo. Fix typo and add header files for
set_irq_type() warnings.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Patch adds IrDA driver support for Texas Instruments OMAP
(http://www.ti.com/omap) based processors like OMAP1610/1710 and OMAP242x.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

If there is a signal pending and wait_for_completion_interruptible_timeout
terminates with -ERESTARTSYS, we return and disable the i2c clocks in
omap_i2c_xfer.

If we terminate before sending last i2c message with a stop condition, the
bus remains busy and we are not able to send new messages into bus with
successive omap_i2c_xfer calls. Therefore a pending signal is not caught
here and we return only because of timeout or i2c error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Fix warning

arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In mach-omap1/mailbox.c the mailbox name is .name = "DSP"
while in plat-omap/dsp/dsp_core.c function  dsp_mbox_init()
asks for "dsp". This results in a strcmp() mismatch and then
OMAP1 system crashes due to NULL pointer. OMAP2 is correct,
there .name is "dsp". Correct OMAP1 name to "dsp" as well.

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Make oprofile work for ARM11
Signed-off-by: Tony Lindgren <tony@atomide.com>

Speling fix:  PRCM_WID for wake-on-id, not PRCM_WLD for bits-gone-WLD.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 64688c2d.

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Updating system time and reprogramming timer can cause latency
issues on busy systems with lots of interrupts with constant
updating of time and reprogramming the system timer.

If a non-timer dyntick interrupt happens within a jiffy from
the last interrupt, updating time and reprogramming the timer
is unnecessary as we will get a timer interrupt soon anyways.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Useful for debugging power management code.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Tighten up error handling in the procfs dump, and avoid returning
bogus values from the read() system call.  Report single vs double
buffering for FIFO setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Remove an oops in the queue fault cleanup path, caused by using the
   wrong giveback routine (heavy weight vs lighter-weight).  Move a few
   key bits of code into that lighter weight version.

 - Trigger that lighter-weight cleanup during URB completion, when the
   URB in question can't yet been handed off to the hardware even if
   it's at the queue head.

 - Reduce syslog noise when those fault cleanup paths are triggered from
   scatterlist calls by usb-storage.

 - Paranoia: when scheduling, insist that the endpoint fifo isn't smaller
   than required.

Oops observed courtesy of a slightly flakey usb-storage device, which
once again proves itself handy for testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Remove #ifdefs in favor of new is_cppi_enabled() macro.
 - Trim some tx-start logic, inlining it and removing MGC_{Read,Write}Csr16()
 - Remove remnant of bogus/non-existent host-side ISO bitfield.

For upstream merging, more such #ifdeffery still needs to be removed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Add header needed for DaVinci build.
 - Remove some partially obsolete comments.
 - Cleaner and more reproducible host side VBUS handling, including
   waiting for it to fall after powerdown on rmmod.
 - Tighten up various state machine transitions and diagnostics

Plus removing some generic #ifdeffery.  The vbus updates make it work more like
the TUSB code, and the cleanups etc make upstream merging more practical.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

When you're willing to trust the USB host not to commit certain errors, the
CPPI "rndis" RX mode can be used with the peripheral side g_ether driver.
(In other cases, rndis rx mode tends to misbehave _very_ rudely ...)

This patch adds a heuristic to detect when the safe scenario is likely, and
a module parameter to disable the heuristic in contexts when it's likely
to fail; for example, users of gadgetfs will likely need to disable it.

This gave about a 60% improvement in throughput with CDC Ethernet (!!) and a
slight reduction in CPU load.  That's measured with TTCP, which pushes a lot
of full size Ethernet frames and thus can see three IRQs per packet reduced
to just one, and also get I/O overlap when double buffering packets.  That is,
net 10 MByte/sec sustained, using double buffering but no DMA transfer queues;
it's unclear why TX is still just 6 MByte/sec.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

<linux/config.h> automatically gets included by kbuild
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):

arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>