Make oprofile work for ARM11
Signed-off-by: Tony Lindgren <tony@atomide.com>

Speling fix:  PRCM_WID for wake-on-id, not PRCM_WLD for bits-gone-WLD.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 64688c2d.

Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Updating system time and reprogramming timer can cause latency
issues on busy systems with lots of interrupts with constant
updating of time and reprogramming the system timer.

If a non-timer dyntick interrupt happens within a jiffy from
the last interrupt, updating time and reprogramming the timer
is unnecessary as we will get a timer interrupt soon anyways.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Useful for debugging power management code.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Tighten up error handling in the procfs dump, and avoid returning
bogus values from the read() system call.  Report single vs double
buffering for FIFO setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Remove an oops in the queue fault cleanup path, caused by using the
   wrong giveback routine (heavy weight vs lighter-weight).  Move a few
   key bits of code into that lighter weight version.

 - Trigger that lighter-weight cleanup during URB completion, when the
   URB in question can't yet been handed off to the hardware even if
   it's at the queue head.

 - Reduce syslog noise when those fault cleanup paths are triggered from
   scatterlist calls by usb-storage.

 - Paranoia: when scheduling, insist that the endpoint fifo isn't smaller
   than required.

Oops observed courtesy of a slightly flakey usb-storage device, which
once again proves itself handy for testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Remove #ifdefs in favor of new is_cppi_enabled() macro.
 - Trim some tx-start logic, inlining it and removing MGC_{Read,Write}Csr16()
 - Remove remnant of bogus/non-existent host-side ISO bitfield.

For upstream merging, more such #ifdeffery still needs to be removed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 - Add header needed for DaVinci build.
 - Remove some partially obsolete comments.
 - Cleaner and more reproducible host side VBUS handling, including
   waiting for it to fall after powerdown on rmmod.
 - Tighten up various state machine transitions and diagnostics

Plus removing some generic #ifdeffery.  The vbus updates make it work more like
the TUSB code, and the cleanups etc make upstream merging more practical.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

When you're willing to trust the USB host not to commit certain errors, the
CPPI "rndis" RX mode can be used with the peripheral side g_ether driver.
(In other cases, rndis rx mode tends to misbehave _very_ rudely ...)

This patch adds a heuristic to detect when the safe scenario is likely, and
a module parameter to disable the heuristic in contexts when it's likely
to fail; for example, users of gadgetfs will likely need to disable it.

This gave about a 60% improvement in throughput with CDC Ethernet (!!) and a
slight reduction in CPU load.  That's measured with TTCP, which pushes a lot
of full size Ethernet frames and thus can see three IRQs per packet reduced
to just one, and also get I/O overlap when double buffering packets.  That is,
net 10 MByte/sec sustained, using double buffering but no DMA transfer queues;
it's unclear why TX is still just 6 MByte/sec.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

<linux/config.h> automatically gets included by kbuild
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):

arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

DSP HW-related initialization is deferred until the first DSP device
node is opened. This allows us to keep DSP powered down before the
DSP SW is loaded.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Sync timer32k code with mainline
Signed-off-by: Tony Lindgren <tony@atomide.com>

These can be static now that CONFIG_OMAP_RESET_CLOCKS
is rearranged.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Nokia770-specific part
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

DSP needs to control some board-specific peripheral devices (GPT,
audio, mbox, etc.) through dspgw kfunc commands.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

- use device model for IRQ detection.
- use "dsp_device" as a pointer for "struct device"
- some whitespaces are cleaned up.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>

Mailbox is restructured as below:

- OMAP1 and OMAP2 parts split out to mach-omap[1-2] respectively.
- struct mbx isolation
- Introduced device model
- Added class interface

Moved omap[1,2] specific parts in mach-omap[1,2]/
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>