NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly

Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix the following build error when CONFIG_B43_LEDS is not selected:

drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: Thomas Ilnseher <illth@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We need to release the SDIO host before locking the driver mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We don't need to call the irqsafe callbacks.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's a check saying
	/* we're good if we have both BSSID and channel */
	if (wdev->conn->params.bssid && wdev->conn->params.channel) {

but that isn't true -- we need the BSS struct. This leads
to errors such as

    Trying to associate with 00:1b:53:11:dc:40 (SSID='TEST' freq=2412 MHz)
    ioctl[SIOCSIWFREQ]: No such file or directory
    ioctl[SIOCSIWESSID]: No such file or directory
    Association request to the driver failed
    Associated with 00:1b:53:11:dc:40

in wpa_supplicant, as reported by Holger.

Instead, we really need to have the BSS struct, and if we
don't, then we need to initiate a scan for it. But we may
already have the BSS struct here, so hang on to it if we
do and scan if we don't.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The contention window is supposed to be a power of two minus one, i.e.
15, 31, 63, 127...  minstrel_rate_init() forgets to subtract 1, so the
sequence becomes 15, 32, 66, 134...

Bug reported by Dan Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix printk format warnings:

drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a new usbid for Zcomax XG-705A to the device table.

Cc: stable@kernel.org
Reported-by: Jari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.

Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Disable SDIO coreswitch debugging.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WEXT's "struct iw_freq" can also be used to handle a channel. This patch now
uses cfg80211_wext_freq() instead of hand-converting the frequency. That
allows user-space to specify channels as well, like with SIOCSIWFREQ.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbc).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.

Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* 'osync_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  fsync: wait for data writeout completion before calling ->fsync
  vfs: Remove generic_osync_inode() and sync_page_range{_nolock}()
  fat: Opencode sync_page_range_nolock()
  pohmelfs: Use new syncing helper
  xfs: Convert sync_page_range() to simple filemap_write_and_wait_range()
  ocfs2: Update syncing after splicing to match generic version
  ntfs: Use new syncing helpers and update comments
  ext4: Remove syncing logic from ext4_file_write
  ext3: Remove syncing logic from ext3_file_write
  ext2: Update comment about generic_osync_inode
  vfs: Introduce new helpers for syncing after writing to O_SYNC file or IS_SYNC inode
  vfs: Rename generic_file_aio_write_nolock
  ocfs2: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
  pohmelfs: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
  vfs: Remove syncing from generic_file_direct_write() and generic_file_buffered_write()
  vfs: Export __generic_file_aio_write() and add some comments
  vfs: Introduce filemap_fdatawait_range

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw:
  GFS2: Whitespace fixes
  GFS2: Remove unused sysfs file
  GFS2: Be extra careful about deallocating inodes
  GFS2: Remove no_formal_ino generating code
  GFS2: Rename eattr.[ch] as xattr.[ch]
  GFS2: Clean up of extended attribute support
  GFS2: Add explanation of extended attr on-disk format
  GFS2: Add "-o errors=panic|withdraw" mount options
  GFS2: jumping to wrong label?
  GFS2: free disk inode which is deleted by remote node -V2
  GFS2: Add a document explaining GFS2's uevents
  GFS2: Add sysfs link to device
  GFS2: Replace assertion with proper error handling
  GFS2: Improve error handling in inode allocation
  GFS2: Add some more info to uevents
  GFS2: Add online uevent to GFS2

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
  udf: Fix possible corruption when close races with write
  udf: Perform preallocation only for regular files
  udf: Remove wrong assignment in udf_symlink
  udf: Remove dead code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (21 commits)
  fs/Kconfig: move nilfs2 outside misc filesystems
  nilfs2: convert nilfs_bmap_lookup to an inline function
  nilfs2: allow btree code to directly call dat operations
  nilfs2: add update functions of virtual block address to dat
  nilfs2: remove individual gfp constants for each metadata file
  nilfs2: stop zero-fill of btree path just before free it
  nilfs2: remove unused btree argument from btree functions
  nilfs2: remove nilfs_dat_abort_start and nilfs_dat_abort_free
  nilfs2: shorten freeze period due to GC in write operation v3
  nilfs2: add more check routines in mount process
  nilfs2: An unassigned variable is assigned to a never used structure member
  nilfs2: use GFP_NOIO for bio_alloc instead of GFP_NOWAIT
  nilfs2: stop using periodic write_super callback
  nilfs2: clean up nilfs_write_super
  nilfs2: fix disorder of nilfs_write_super in nilfs_sync_fs
  nilfs2: remove redundant super block commit
  nilfs2: implement nilfs_show_options to display mount options in /proc/mounts
  nilfs2: always lookup disk block address before reading metadata block
  nilfs2: use semaphore to protect pointer to a writable FS-instance
  nilfs2: fix format string compile warning (ino_t)
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: consolidate reconnect logic in smb_init routines
  cifs: Replace wrtPending with a real reference count
  cifs: protect GlobalOplock_Q with its own spinlock
  cifs: use tcon pointer in cifs_show_options
  cifs: send IPv6 addr in upcall with colon delimiters
  [CIFS] Fix checkpatch warnings
  PATCH] cifs: fix broken mounts when a SSH tunnel is used (try #4)
  [CIFS] Memory leak in ntlmv2 hash calculation
  [CIFS] potential NULL dereference in parse_DFS_referrals()