Fixes the following errors on both tps650xx regulator drivers :-

drivers/regulator/tps65023-regulator: struct i2c_device_id is 32 bytes.  The last of 1 is:
0x74 0x70 0x73 0x36 0x35 0x30 0x32 0x33 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
FATAL: drivers/regulator/tps65023-regulator: struct i2c_device_id is not terminated with a NULL entry!

This patch also fixes the GPL v2 licence string for both drivers.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This fixes a spelling error and an API function signature mismatch
in the regulator documentation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Adding TPS65023 and TPS6507x regulator driver support in
drivers/regulator/Makefile and drivers/regulator/Kconfig
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Adding support for TI TPS6507x regulator driver
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Adding support for TI TPS65023 regulator driver
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

and avoid introducing our own loops for creating
several sysfs entries.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Now fixed regulators that have their enable pin connected to a GPIO line
can use the fixed regulator driver for regulator enable/disable control.
The GPIO number and polarity information is passed through platform data.
GPIO enable control is achieved using gpiolib.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch implements list_voltage for the pcf50644 regulator driver.
As the voltages are linearly scaled the code to convert register values to
voltages can be reused and most of the code can be shared with get_voltage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The regulator_enable() code wasn't actually checking that the
machine constraints had given permission to enable the regulator.
Add code to do that, but only if the regulator is not already on
due to something like always_on or being left on at startup since
in those cases there's no physical change being introduced and the
constraint wouldn't make any sense.

Also add matching code for disable(). We need to do less there since
either regulator_enable() should have succeeded first or the board
setup makes no sense.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Allows use by more of the internal regulator API code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This is useful for implementing get_status() in terms of get_mode().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Report errors to the user and try harder to clean up if we're not
able to probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The patch to add support for looking up consumers by device name
had the side effect of causing us to require a device which is
at best premature since at least cpufreq still operates outside
the device model. Remove that requirement.
Reported-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

We're probably going to start oopsing fairly soon after this happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Simplify checking of support for voltage ranges by providing an API which
wraps the existing count and list operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Some consumers require complete control of the regulator and can't
tolerate sharing it with other consumers, most commonly because they need
to have the regulator actually disabled so can't have other consumers
forcing it on. This new regulator_get_exclusive() API call allows these
consumers to explicitly request this, documenting the assumptions that
they are making.

In order to simplify coding of such consumers the use count for regulators
they request is forced to match the enabled state of the regulator when
it is requested. This is not possible for consumers which can share
regulators due to the need to keep track of the ownership of use counts.

A new API call is used rather than an additional argument to the existing
regulator_get() in order to avoid merge headaches with driver code in
other trees.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Make da903x driver to list voltage and count voltage.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

In PXA3xx SoC family, V_CORE power doamin is supplied by BUCK1 that is
controller by ADTV1 or ADTV2 register.

By default, v1 and v2 has the same copy. If v1 or v2 is updated, the last
value that is written to either register takes effect. It means that v1
and v2 has different copy. And the actual voltage output is determinated
by last update on either register.

DA9034/35 is binded with PXA3xx SoC family. While SoC is scaling OP or
entering/exiting lower power mode, SoC needs to change voltage of V_CORE
power doamin. In order to be efficient, POWER I2C (hardcode) mode could
be enabled in SoC. In this mode, SoC will control v2 register directly.

In original DA903x driver, software will only read regulator data from v1
register. But SoC controls v2 register directly. It results that v1 and v2
isn't synchronized. Wrong data will be read from v1 register. So access v2
register in da903x driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Support the operation of DA9030 BUCK2 in da903x driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

BUCK3 is the new component in DA9035. So there're three BUCKs in DA9035.
And there're two BUCKs in DA9034.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This allows machine drivers to build without ifdefs if they have
full constraints. Suggested by machine drivers contributed by
Haojian Zhuang <haojian.zhuang@gmail.com>.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Follow the approach suggested by Russell King and implemented by him in
the clkdev API and allow consumer device supply mapings to be set up
using the dev_name() for the consumer instead of the struct device.
In order to avoid making existing machines instabuggy and creating merge
issues the use of struct device is still supported for the time being.

This resolves problems working with buses such as I2C which make the
struct device available late providing that the final device name is
known, which is the case for most embedded systems with fixed setups.

Consumers must still use the struct device when calling regulator_get().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This makes it easier to read the logs when doing testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The core will no longer complain so we should log an error here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Ensure that reg is within the bounds of array wm8350->pmic.pdev[].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  virtio: net refill on out-of-memory
  smc91x: fix compilation on SMP

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ps3: Update ps3_defconfig
  powerpc/ps3: Add missing check for PS3 to rtc-ps3 platform device registration

Update ps3_defconfig.

 o Refresh for 2.6.31.
 o Remove MTD support.
 o Add more HID drivers.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On non-PS3, we get:

| kernel BUG at drivers/rtc/rtc-ps3.c:36!

because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  IMA: iint put in ima_counts_get and put

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k,m68knommu: Wire up rt_tgsigqueueinfo and perf_counter_open
  m68k: Fix redefinition of pgprot_noncached
  arch/m68k/include/asm/motorola_pgalloc.h: fix kunmap arg
  m68k: cnt reaches -1, not 0
  m68k: count can reach 51, not 50

If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request.  It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.

All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails.  The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>