Use our actual device for dev_dbg and friends, not some blank fake
struct.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Move other statics and globals into device struct. Shrink some of the
flags into single-bit fields, and the more often used flags into
bools.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Move mmcsd_base into device struct.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Deprecate use of volatile registers structure.  Use I/O accessor
functions instead.  Demystify magic constants.

This is moved to use ioremap later in the patch series.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Make davinci-mmc mostly scripts/checkpatch.pl compliant.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Here is a quick fix to compile for the davinci_mmc driver in the
latest git kernel: they changed error codes to standard and use
sg_virt to get the scatterlist page.
Signed-off-by: Vitaly Makarov <vit.macarrow@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

If an interrupt happens before an I2c master read/write,
complete is called on uninitialized structure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

If wait_for_completion_interruptible_timeout exits due
to a signal, the i2c bus was locking up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Interrupts are enabled at the point where
the DAVINCI_I2C_IVR_REG is read, so unless
an interrupt happened just at that moment,
no interrupt would be pending. Even though
documentation implies you should do this,
I see no reason. If slave support is added,
this read would cause a hard to reproduce bug.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

When a dma channel is opened, clear all pending events.  Remove SAM &
DAM bits if source or destination isn't a fifo.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

MASK_ALE = 0x0A may always work, but
MASK_ALE = 0x08 is much more logical
Only 1 address line is hooked to ALE, not 2
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

scripts/checkpatch corrections
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

ARM: DaVinci: fix ethernet lockup again
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

davinci-i2c: fix lost interrupt
DAVINCI_I2C_STR_REG is a write 1 to clear register,
so don't use a read/modify/write cycle.
EVM doesn't have platform data yet, make bus_delay default correct
Ensure psc value gives a clock between 7-12 Mhz
Make sure no interrupts are pending before starting transfer
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Fix NAND compilation after update to 2.6.24. nand_platform_data
doesn't exist any more.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

The patch uses the spinlock version of netif_rx_complete
to fix ethernet lockup.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Signed-off-by: Kevin Hilman <khilman@mvista.com>

Signed-off-by: Kevin Hilman <khilman@mvista.com>

Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Pass physical addresses in the i2c platform data since they
are converted to virtual in the i2c driver.
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Special thanks to Dirk for the IDE and net fixes.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Conflicts:

	drivers/i2c/busses/i2c-davinci.c
	drivers/media/video/Makefile
	drivers/media/video/video-buf.c
	drivers/mmc/host/Kconfig
	drivers/mmc/host/Makefile
	drivers/mtd/nand/Kconfig
	drivers/mtd/nand/Makefile
	drivers/video/Makefile
	include/linux/ide.h
	include/media/video-buf.h

This patch converts audio driver to use platform driver (and minor
style changes).

This fixes broken standby resume as reported in

http://linux.omap.com/pipermail/davinci-linux-open-source/2008-January/004919.html

Switching to platform_driver, the driver suspends and resumes properly
now. platform_resume_early() doesn't call uninitialized tasklet worker
function audio_dsr_handler() any more. From oops reported in link
above:

(audio_dsr_handler+0x0/0x7c) from [<c014f848>]
(platform_resume_early+0x30)
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

To: davinci-linux-open-source@linux.davincidsp.com
Date: Sat, 12 Jan 2008 07:39:48 +0100

This patch adds NAND driver to recent git. Tested on DM6446 DVEVM.

It is mainly based on Sander Huijsen <Shuijsen@optelecom-nkf.com> work

http://linux.omap.com/pipermail/davinci-linux-open-source/2007-December/004788.html

and HW ECC changes from Troy Kisky <troy.kisky@boundarydevices.com>

http://linux.omap.com/pipermail/davinci-linux-open-source/2008-January/004910.htmlSigned-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

To: davinci-linux-open-source@linux.davincidsp.com
Date: Sat, 12 Jan 2008 07:39:33 +0100

This patch exports davinci_mux_peripheral() to be used in
modules. Needed to compile NAND driver as module. Thanks to Kevin for
the hint!
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Enable OneNAND driver to build as a module, which requires exporting
GPMC request/free functions it depends on.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

host->slot_id = (pdev->id - 1) definition is wrong. For each hsmmc host controller's
instance, the first slot always has id=0.
Signed-off-by: David Cohen <david.cohen@indt.org.br>
Acked-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds OMAP EHCI glue layer and Menu config option.
Incorporated Paul Walmsley review comments on usage of
cm_{read,write}_mod_reg().
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Kamat, Nishant <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds the OMAP EHCI board specific information
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Kamat, Nishant <nskamat@ti.com>
Acked-by: David, Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds CM defines used by OMAP EHCI on OMAP34xx.
Incorporated Paul Walmsley review comments.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update 3430sdp defconfig
Signed-off-by: tony Lindgren <tony@atomide.com>

This patch adds pinmux support for OMAP3. Incorporated review comments
from Tony to make mux_value as bit mask. Tested on 3430SDP.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the newer touchscreen driver (tsc210x).
The old one doesn't compile anymore.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add missing select ARCH_OMAP_OTG on 2430sdp and 3430sdp builds.
Signed-off-by: Felipe Balbi <felipe.souza-lima-de@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix for the Touch Screen issue on OMAP3 ES2.0.The IRQ for the TS has been defined as 3 and 2 for ES1 and ES2
and the IRQ assignment is done at run time.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The LCD controller (EPSON S1D13744) supports
rotation (0, 90, 180 and 270 degrees) on hardware just setting
the bits 0 and 1 of 0x28 register (LCD Panel Configuration Register).
Now it is possible to use this caps only setting the angle degree on var rotate of fb_var_screeninfo using the FBIOPUT_VSCREENINFO ioctl.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@openbossa.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Including board file board-2430osk.h missed.

drivers/i2c/chips/twl4030_core.c:480: error: `IH_TWL4030_BASE' undeclared (first use in this function)
drivers/i2c/chips/twl4030_core.c:853: error: `IH_TWL4030_END' undeclared (first use in this function)
drivers/i2c/chips/twl4030_core.c:860: error: `TWL4030_IRQNUM' undeclared (first use in this function)
drivers/i2c/chips/twl4030_gpio.c:249: error: `IH_TWL4030_GPIO_BASE' undeclared (first use in this function)
drivers/i2c/chips/twl4030_gpio.c:787: error: `IH_TWL4030_BASE' undeclared (first use in this function)
...
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Including MACH_TYPE_OMAP_2430OSK missed type.

arch/arm/mach-omap2/board-2430osk.c:134: error: `MACH_TYPE_OMAP_2430OSK' undeclared here (not in a function)
arch/arm/mach-omap2/board-2430osk.c:134: error: initializer element is not constant
arch/arm/mach-omap2/board-2430osk.c:134: error: (near initialization for `__mach_desc_OMAP_2430OSK.nr')
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>