Print reserved memory only if it was actually reserved.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The size status field in DISPC_[GFX | VID1 | VID2]_FIFO_SIZE_STATUS
register is 11 bits wide in OMAP3, but only 9 bits were read. Similarly,
the threshold field in DISPC_[GFX | VID1 | VID2]_FIFO_THRESHOLD register
is 12 bits wide, while only 9 bits were written in it.

This patch extends the bit field sizes used in setup_plane_fifo to
correspond to ones in OMAP3. In OMAP2 the extra bits are reserved, so no
harm should come from extending the bit fields.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove CONFIG_OMAP_SYSOFFMODE flag and do the full initialization of voltage
controller . Enabling automatic sending of OFF command and selecting wether
SYS_OFF_MODE signal is used should be determined dynamically. Hence they are
now not set in the initialization.

The sleep voltage for OFF mode is changed to default 1,2V for VDD1 and
1,15V for VDD2. Using the 0,9V setting causes hangup.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is exactly the same as the overo configuration. It might make sense
to have them in a single one.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>

# CHANGED to not spew messages about beagle on non-beagle boards
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds support for basic features: nand, uarts, i2c,
mmc, rtc, and usb. Also includes defconfig.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.

However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.

If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:

irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq():  c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000

Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 3da0e102.

The real bug behind this issue is the fact that we're not
masking out the SPURIOUSIRQFLAG bits [31:7] from the active
interrupt number. The following patch will replace this
patch with the fix.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix following bootup crash on LDP platform by enabling T2 USB driver for MUSB

Backtrace:
[<c001b9ac>] (musb_platform_init+0x0/0x120) from [<c001b0a8>] (musb_probe+0x208/0xb0c)
 r5:00000000 r4:c0222ad4
[<c001aea0>] (musb_probe+0x0/0xb0c) from [<c0142e80>] (platform_drv_probe+0x20/0x24)
[<c0142e60>] (platform_drv_probe+0x0/0x24) from [<c0142118>] (driver_probe_device+0xd0/0x17c)
[<c0142048>] (driver_probe_device+0x0/0x17c) from [<c0142210>] (__driver_attach+ 0x4c/0x70)
 r7:c0233214 r6:c0233214 r5:c02229ec r4:c0222940
[<c01421c4>] (__driver_attach+0x0/0x70) from [<c0141790>] (bus_for_each_dev+0x4c/0x84)
 r7:c0233214 r6:c01421c4 r5:c781de94 r4:00000000
[<c0141744>] (bus_for_each_dev+0x0/0x84) from [<c0141f60>] (driver_attach+0x20/0x28)
 r7:c78999c0 r6:c0234c60 r5:c0233214 r4:00000000
[<c0141f40>] (driver_attach+0x0/0x28) from [<c0141c1c>] (bus_add_driver+0xa8/0x214)
[<c0141b74>] (bus_add_driver+0x0/0x214) from [<c0142404>] (driver_register+0x98/0x120)
 r8:00000000 r7:00000000 r6:c0234c60 r5:c0233214 r4:c001e5c4
[<c014236c>] (driver_register+0x0/0x120) from [<c014303c>] (platform_driver_register+0x78/0x94)
[<c0142fc4>] (platform_driver_register+0x0/0x94) from [<c0143070>] (platform_driver_probe+0x18/0x68)
[<c0143058>] (platform_driver_probe+0x0/0x68) from [<c001ad38>] (musb_init+0x3c/0x54)
 r5:c001e510 r4:c001e5c4
[<c001acfc>] (musb_init+0x0/0x54) from [<c0022298>] (__exception_text_end+0x50/0x168)
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 8b1f0bd4 introduced a bug that
caused non-CORE DPLL rates to be incorrectly set on boot in
omap3_noncore_dpll_enable().  Debugged by Tomi Valkeinen
<tomi.valkeinen@nokia.com> - thanks Tomi.

Also fix omap3_noncore_dpll_set_rate() to assign clk->rate after a
DPLL reprogram.

Tested on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Cc: Rick Bronson <rick@efn.org>
Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

num_eps is 16, not 32.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix these compiler warnings:
smartreflex.c:126: warning: initialization makes integer from pointer without a cast
smartreflex.c:134: warning: initialization makes integer from pointer without a cast

Refreshed after updates from Felipe.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Sync nand.h with mainline kernel

Moving NAND_BLOCK_SIZE definition to board-3430sdp-flash.c
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes two problems in LM8323 PWM control. One is that
locking is needed when setting and reading pwm->desired_brightness
asynchronously. The other is that LM8323 may stop a PWM script only
after the current instruction has finished. If it is a long RAMP,
the chip would keep executing the old instruction and new
settings were effectively ignored.
Signed-off-by: Timo Karjalainen <timo.o.karjalainen@nokia.com>
Signed-off-by: Daniel Stone <daniel.stone@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is no reason to limit the GPIO rows to 6 for
OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO interrupts has been disabled several times
after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

That cast was annyoing for quite a while. Now
omap_ctrl_base_get() returns void __iomem *
and __raw_read/write friends uses void __iomem *
so there's no need for casting.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adding MCBSP port 1, 3, 4 and 5 ports mux settings for 2430.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enables mcspi support in omap2evm defconfig
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adding ads7846 touchscreen support to omap2evm board
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds mcspi1 and gpio_85 mux configuration for 2430.
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

As sugested by RMK
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Various cleanups to the OMAP EHCI bus glue:

 - Whitespace fixes.

 - Busy-wait loops should really have timeouts, but lacking
   that ... at least cpu_relax() in the body.

 - Debug messages should end with newlines, so they don't
   break the next message; should not embed newlines; and
   should otherwise be clean and correctly spelled.

 - The probe() method should have initialized the SBRN value,
   so the driver didn't report "USB 0.0 started".

 - The MODULE_ALIAS() was missing its "platform:" prefix;
   doing it right means the module could hotplug/coldplug.

No real functional change except for the hotplug/coldplug thing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This prevents spurious interrupts from repeating unacked and
thus locking the system, while still allowing the spurious
bad irq error message to be show on console.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is until the EHCI issues have been sorted out.
Signed-off-by: Tony Lindgren <tony@atomid.com>

Update defconfigs for boards that have EHCI set
Signed-off-by: Tony Lindgren <tony@atomide.com>

debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.

Comparing to PATCH v1, because clk_debugfs_init is included in
"#if defined CONFIG_DEBUG_FS", we only need to check NULL return.
Thanks Li Zefan <lizf@cn.fujitsu.com>

debugfs_create_u8() and other function's return value's checking method are
also fixed in this patch.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Wed, Oct 8, 2008 at 11:36 AM, Nathan Monson <nmonson@gmail.com> wrote:
> "Felipe Contreras" <felipe.contreras@gmail.com> writes:
>> irq -33, desc: c0335cf8, depth: 0, count: 0, unhandled: 0
>
> On the BeagleBoard list, Pratheesh Gangadhar said that mapping I/O
> regions as Strongly Ordered suppresses this problem:
> http://groups.google.com/group/beagleboard/browse_thread/thread/23e1c95b4bfb09b5/70d12dca569ca503?show_docid=70d12dca569ca503

Pratheesh helped me make a patch against the latest linux-omap git to
try this.

With this patch, my IRQ -33 problems with the DSP have disappeared.
Before, I would end up in IRQ -33 loop after 10 invocations of the DSP
Bridge 'ping.out' utility.  I just finished running it 50,000 times
without error.

As stated before, this patch is just a workaround for testing
purposes, not a fix.  Who knows what performance side effects it
has...
Signed-off-by: Nathan Monson <nmonson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The i2c_driver in twl4030-core.c and platform_driver of twl4030-usb.c
both has the name twl4030_driver. This leads to unnecessary confusion.

So rename the usb platform_driver appropriately to:
twl4030_usb_driver.
Signed-off-by: Jagadeesh Bhaskar Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Replace stubbed-out card-detect support for twl4030 GPIOs with
a simpler platform_data mechanism.  As before, no current users.
Sanity tested by enabling this on Beagle; it booted OK with
root on MMC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Export Beagle's third LED to the LED framework, now that it's
accessible through the twl4030-gpio code.

Claim the VBUS control, defaulting to OFF.  Boards that have an
EHCI connector (not rev B) will need to update this slightly.
(Ideally as part of adding hooks to the ehci-map code supporting
external power switching and overcurrent detection.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Expose the two TWL4030 LED signals as output-only GPIOs.  Boards
need to explicitly ask that this be done, to help avoid conflicts
on boards using these same pins to hook up to a vibrator motor.

Note that these are high drive open drain signals; LEDA is rated
for up to 160 mA (!), LEDB up to 60 mA.  Boards using one of these
signals to drive a bank of LCD backlight LEDs would probably want
to access the dedicated PWMs for brightness control, too; easy to
add such support later.

Example:  Beagle has one real LED here (PWM not necessary), and
one GPIO controlling VBUS output over EHCI (PWM not wanted).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Convert the hsmmc init code over to standard GPIO calls:
gpio_request(), gpio_free(), gpio_get_value_cansleep().

NOTE that this doesn't pass GPIO numbers in to hsmmc_init();
those values are still hard-wired.  (For the write protect
signal, the LACK of value is hard-wired...)  So the hsmmc
glue is still kind of problematic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the new gpiolib internal mechanism for tracking gpio usage,
making them power the GPIO module on/off, so that the standard
gpio_request()/gpio_free() calls can completely replace the
twl4030-specific versions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a new internal mechanism to gpiolib to support low power
operations by letting gpio_chip instances see when their GPIOs
are in use.  When no GPIOs are active, chips may be able to
enter lower powered runtime states by disabling clocks and/or
power domains.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove now unncessary casts and use the same order for include files.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Simplify handling of VBUS and ID status and the USB_PRES interrupt.
This seems to resolve the problems I previously saw on Beagle and
Overo boards.

 - Read the status directly, instead of trying to infer it from
   dodgey side effects of IRQ handling and trigger tweaking.

 - Stop trying to arrange those dodgey side effects; just leave
   the IRQ enabled at all times.

 - Check that status as part of driver probe, so the PHY can
   always be active by the time it's needed.  (BUGFIX!)

 - Re-sequence probe() to be less racey, and to avoid duplicating
   logic found elsewhere (notably irq handling and PHY activation).

 - Make the irq_chip be the exclusive owner of PWR_EDR (finally).

 - Get rid of needless work_struct ... in this irq handling thread,
   it's safe and cheap to call sysfs_notify() directly.

Stop enabling IRQs on the USB subchip.  There's no IRQ handler for
them, and since ALT_INT_REROUTE isn't being set they'll never
arrive ... so there's no point to enabling them.

Also add some comments about other things such an otg_transciever
driver should be doing, fixing minor omissions; and remove some
unnecessary file inclusions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Disable more unnecessary TWL4030_*IRQ_* symbols.

We're not yet ready to remove them all from <linux/i2c/twl4030.h>
since various drivers still use those symbols (maybe indirectly)
not platform resources: twl4030_bci_battery.c, twl4030-madc.c,
twl4030-pwrbutton.c, and omap-twl4030keypad.c all need updates.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Replace twl4030 GPIO IRQ handling with generic SIH support.
No change in functionality; but there's now one less kernel
thread tied up supporting this chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>