- 21 Dec, 2007 12 commits
-
-
Masato Noguchi authored
This changes the spu context switch code to not write to reserved bits of spu interrupt status register. The architecture book says the reserved fields should be set to zero. Signed-off-by:
Masato Noguchi <Masato.Noguchi@jp.sony.com> Signed-off-by:
Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
Paul Mackerras <paulus@samba.org>
-
Luke Browning authored
Need to re-check priority after dropping lock. Otherwise, a more favored context may be preempted. Signed-off-by:
Luke Browning <lukebr@linux.vnet.ibm.com> Signed-off-by:
-
Luke Browning authored
This cleans up spu_run_init so that it does all of the spu initialization for spufs_run_spu. It initializes the spu context as much as possible before it activates the spu and writes the runcntl register. Signed-off-by:
-
Jeremy Kerr authored
Based on original patches from Arnd Bergmann <arnd.bergman@de.ibm.com>; and Luke Browning <lukebr@linux.vnet.ibm.com> Currently, spu contexts need to be loaded to the SPU in order to take class 0 and class 1 exceptions. This change makes the actual interrupt-handlers much simpler (ie, set the exception information in the context save area), and defers the handling code to the spufs_handle_class[01] functions, called from spufs_run_spu. This should improve the concurrency of the spu scheduling leading to greater SPU utilization when SPUs are overcommited. Signed-off-by:
-
Jeremy Kerr authored
Add a few #defines for the class 0, 1 and 2 interrupt status bits, and use them instead of magic numbers when we're setting or checking for these interrupts. Also, add a #define for the class 2 mailbox threshold interrupt mask. Signed-off-by:
-
Jeremy Kerr authored
When doing a poll on the mbox stat file of a swapped-out context, we clear the class 0 interrupt status, rather than the class 2 interrupt status. This change corrects the poll operation to clear the correct interrupt. Signed-off-by:
-
Luke Browning authored
This change encapsulates the spu_privcntl_RW register so that it can be written through backing ops. This is necessary so that spu contexts can be initialized and queued to the scheduler in spufs_run_spu. Signed-off-by:
-
Arnd Bergmann authored
This change disables the logic that faults-in spu contexts under the covers from the page fault handler. When a fault requires a runnable context, the handler will block until the context is scheduled by other means. Signed-off-by:
Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by:
-
Jeremy Kerr authored
Currently, part of the spufs code (switch.o, lscsa_alloc.o and fault.o) is compiled directly into the kernel. This change moves these components of spufs into the kernel. The lscsa and switch objects are fairly straightforward to move in. For the fault.o module, we split the fault-handling code into two parts: a/p/p/c/spu_fault.c and a/p/p/c/spufs/fault.c. The former is for the in-kernel spu_handle_mm_fault function, and we move the rest of the fault-handling code into spufs. Signed-off-by:
-
Julio M. Merino Vidal authored
Fix a few typos in the spufs scheduler comments Signed-off-by:
Julio M. Merino Vidal <jmerino@ac.upc.edu> Signed-off-by:
-
Masato Noguchi authored
Add platform specific SPU run control routines to the spufs. The current spufs implementation uses the SPU master run control bit (MFC_SR1[S]) to control SPE execution, but the PS3 hypervisor does not support the use of this feature. This change adds the run control wrapper routies spu_enable_spu() and spu_disable_spu(). The bare metal routines use the master run control bit, and the PS3 specific routines use the priv2 run control register. An outstanding enhancement for the PS3 would be to add a guard to check for incorrect access to the spu problem state when the spu context is disabled. This check could be implemented with a flag added to the spu context that would inhibit mapping problem state pages, and a routine to unmap spu problem state pages. When the spu is enabled with ps3_enable_spu() the flag would be set allowing pages to be mapped, and when the spu is disabled with ps3_disable_spu() the flag would be cleared and mapped problem state pages would be unmapped. Signed-off-by:
Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by:
-
Emil Medve authored
When a module has relocation sections with tens of thousands of entries, counting the distinct/unique entries only (i.e. no duplicates) at load time can take tens of seconds and up to minutes. The sore point is the count_relocs() function which is called as part of the architecture specific module loading processing path: -> load_module() generic -> module_frob_arch_sections() arch specific -> get_plt_size() 32-bit -> get_stubs_size() 64-bit -> count_relocs() Here count_relocs is being called to find out how many distinct targets of R_PPC_REL24 relocations there are, since each distinct target needs a PLT entry or a stub created for it. The previous counting algorithm has O(n^2) complexity. Basically two solutions were proposed on the e-mail list: a hash based approach and a sort based approach. The hash based approach is the fastest (O(n)) but the has it needs additional memory and for certain corner cases it could take lots of memory due to the degeneration of the hash. One such proposal was submitted here: http://ozlabs.org/pipermail/linuxppc-dev/2007-June/037641.html The sort based approach is slower (O(n * log n + n)) but if the sorting is done "in place" it doesn't need additional memory. This has O(n + n * log n) complexity with no additional memory requirements. This commit implements the in-place sort option. Signed-off-by:
Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by:
-
- 20 Dec, 2007 28 commits
-
-
Julia Lawall authored
There should be an of_node_put when breaking out of a loop that iterates using for_each_node_by_type. This was detected and fixed using the following semantic patch. (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ identifier d; type T; expression e; iterator for_each_node_by_type; @@ T *d; ... for_each_node_by_type(d,...) {... when != of_node_put(d) when != e = d ( return d; | + of_node_put(d); ? return ...; ) ...} // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Cc: Christian Krafft <krafft@de.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: David Erb <djerb@us.ibm.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Julia Lawall authored
There should be an of_node_put when breaking out of a loop that iterates over calls to of_find_all_nodes, as this function does an of_node_get on the value it returns. This was fixed using the following semantic patch. (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ type T; identifier d; expression e; @@ T *d; ... for (d = NULL; (d = of_find_all_nodes(d)) != NULL; ) {... when != of_node_put(d) when != e = d ( return d; | + of_node_put(d); ? return ...; ) ...} // </smpl> Signed-off-by:
-
Julia Lawall authored
Remove an unnecessary pci_dev_put. pci_dev_put is called implicitly by the subsequent call to pci_get_device. The problem was detected using the following semantic patch, and corrected by hand. @@ expression dev; expression E; @@ - pci_dev_put(dev) ... when != dev = E - pci_get_device(...,dev) Signed-off-by:
-
Lucas Woods authored
Signed-off-by:
Lucas Woods <woodzy@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Lucas Woods authored
Signed-off-by:
-
Li Zefan authored
The casting is safe only when the list_head member is the first member of the structure, and even then it is better to use the address of the list_head structure member. Signed-off-by:
Li Zefan <lizf@cn.fujitsu.com> Signed-off-by:
-
Cyrill Gorcunov authored
This fixes a possible NULL pointer dereference inside of strncmp() if of_get_property() fails. Signed-off-by:
Cyrill Gorcunov <gorcunov@gmail.com> Signed-off-by:
-
Stephen Rothwell authored
We were using -mno-minimal-toc on everything in arch/powerpc/kernel, which means that all the functions in there were putting all their TOC entries in the top-level TOC, and it was overflowing on an allyesconfig build. For various reasons, prom_init.c does need -mno-minimal-toc, but the other .c files in there can use sub-TOCs quite happily. This change is sufficient for now to stop the TOC overflowing; other directories under arch/powerpc also use -mno-minimal-toc and could also be changed later if necessary. Lmbench runs with and without this patch showed no significant speed differences. Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Benjamin Herrenschmidt authored
The PCI IRQ code has a fallback when the device-tree parsing fails, that tries to map the interrupt indicated by PCI_INTERRUPT_LINE if the firmware set something in there. This is a bit fragile but has proven useful in some cases so far. However, it's causing us to incorrectly try to map interrupt 0 on various setups, so let's prevent that case, as none of the cases where the fallback is legit should have an IRQ 0. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
This patch changes the PowerPC PCI code to disable IO and/or Memory decoding on a PCI device when a resource of that type failed to be allocated. This is done to avoid having unallocated dangling BARs enabled that might try to decode on top of other devices. If a proper resource is assigned later on, then pci_enable_device() will take care of re-enabling decoding. Signed-off-by:
-
Benjamin Herrenschmidt authored
Apple firmware has a strange way to "close" bridge resources by setting them to some bogus values that overlap RAM (strangely, I haven't seen it conflicting with DMA so far...). This explicitely closes them to avoid problems. Previously, they would be closed as a consequence of failing to be allocated, but this makes it more explicit, and thus the log message is more explicit too. Signed-off-by:
-
Benjamin Herrenschmidt authored
The device node for the HT bridge on G5s doesn't contain useful ranges. We used to give it a bunch of the known PCI space and then punch a "hole" in it based on where the AGP or PCIe region was. This reworks it to use the actual register in the bridge that controls the decoding instead. Signed-off-by:
-
Benjamin Herrenschmidt authored
This enables the PCI code to see the device that represents the HT host bridge on the PowerMac G5. Signed-off-by:
-
Benjamin Herrenschmidt authored
Our implementation of pcibios_enable_device() has a couple of problems. One is that it should not check IORESOURCE_UNSET, as this might be left dangling after resource assignment (shouldn't but there are bugs), but instead, we make it check resource->parent which should be a reliable indication that the resource has been successfully claimed (it's in the resource tree). Then, we also need to skip ROM resources that haven't been enabled as x86 does. Signed-off-by:
-
Benjamin Herrenschmidt authored
It should now be safe to re-assign unassigned resources on 64 bits PowerMac machines (G5s). This clears pci_probe_only on those. Signed-off-by:
-
Benjamin Herrenschmidt authored
Powermac's use of the pcibios_enable_device_hook() got slightly broken by the recent PCI merge in that it won't be called for the "initial" case of assigning resources to a previously unassigned device. This was an abuse of that hook anyway, so instead we now use a header quirk. While at it, we move a #ifdef CONFIG_PPC32 to enclose more code that is only ever used on 32 bits. Signed-off-by:
-
Benjamin Herrenschmidt authored
This merge the two implementations, based on the previously fixed up 32 bits one. The pcibios_enable_device_hook in ppc_md is now available for ppc64 use. Also remove the new unused "initial" parameter from it and fixup users. Signed-off-by:
-
Benjamin Herrenschmidt authored
Our implementation of pcibios_enable_device() incorrectly ignores the mask argument and always checks that all resources have been allocated, which isn't the right thing to do anymore. Signed-off-by:
-
Benjamin Herrenschmidt authored
The way iSeries manages PCI IO and Memory resources is a bit strange and is based on overriding the content of those resources with home cooked ones afterward. This changes it a bit to better integrate with the new resource handling so that the "virtual" tokens that iSeries replaces resources with are done from the proper per-device fixup hook, and bridge resources are set to enclose that token space. This fixes various things such as the output of /proc/iomem & ioports, among others. This also fixes up various boot messages as well. Signed-off-by:
-
Benjamin Herrenschmidt authored
The 32 bits PCI code now uses the generic code for assigning unassigned resources and an algorithm similar to x86 for claiming existing ones. This works far better than the 64 bits code which basically can only claim existing ones (pci_probe_only=1) or would fall apart completely. This merges them so that the new 32 bits implementation is used for both. 64 bits now gets the new PCI flags for controlling the behaviour, though the old pci_probe_only global is still there for now to be cleared if you want to. I kept a pcibios_claim_one_bus() function mostly based on the old 64 bits code for use by the DLPAR hotplug. This will have to be cleaned up, thought I hope it will work in the meantime. Signed-off-by:
-
Benjamin Herrenschmidt authored
The PCI code in 32 and 64 bits fixes up resources differently. 32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus() while 64 bits does things in various places depending on whether you are using OF probing, using PCI hotplug, etc... This merges those by basically using the 32 bits approach for both, with various tweaks to make 64 bits work with the new approach. Signed-off-by:
-
Benjamin Herrenschmidt authored
This merges the PowerPC 32 and 64 bits version of pcibios_resource_to_bus and pcibios_bus_to_resource(). Signed-off-by:
-
Benjamin Herrenschmidt authored
This adds flags the platforms can use to enable domain numbers in /proc/bus/pci. Signed-off-by:
-
Benjamin Herrenschmidt authored
The 32 bits PCI code carries an old hack that was only useful for G5 machines. Nowdays, the 32 bits kernel doesn't support any of those machines anymore so the hack is basically never used, so remove it. Signed-off-by:
-
Benjamin Herrenschmidt authored
This adds to the 32 bits PCI code some flags, replacing the old pci_assign_all_busses global, that allow us to control various aspects of the PCI probing, such as whether to re-assign all resources or not, or to not try to assign anything at all. This also adds the flag x86 already has to avoid ISA alignment on bridges that don't have ISA forwarding enabled (no legacy devices on the top level bus) and sets it for PowerMacs. Signed-off-by:
-
Benjamin Herrenschmidt authored
The 32 bits PowerPC PCI code has a hack for use by some PowerMacs to try to re-open PCI<->PCI bridge IO resources that were closed by the firmware. This is no longer necessary as the generic code will now do that for us. Signed-off-by:
-
Benjamin Herrenschmidt authored
This makes the 32 bits PowerPC PCI code use the generic code to assign resources to devices that had unassigned or conflicting resources. This allow us to remove the local implementation that was incomplete and could not assign for example a PCI<->PCI bridge from scratch, which is needed on various embedded platforms. Signed-off-by:
-
Benjamin Herrenschmidt authored
There's a stale & bogus piece of code in 32 bits PCI code that complains about ISA related alignment issues. Just remove it. Signed-off-by:
-
