Allow phylib specification of cases where hardware needs to configure
PHYs for Internal Delay only on either RX or TX (not both).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting.  On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Version for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.

Resloves problem described in: 	 http://lkml.org/lkml/2007/11/6/395Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
  is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Merge branch 'fixes-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: Fix static rate if path faster than link
  IPoIB: Fix oops if xmit is called when priv->broadcast is NULL

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix build.
  [MIPS] Fix use of smp_processor_id() in preemptible code.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
 [<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
 [<802e4b84>] debug_smp_processor_id+0xd4/0xf0
 [<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.

Cpu options of cpu0 are assumed to be the superset of all processors.

Can I make the same assumptions for cache line size  and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling).  Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4680/1: parentheses around NR_IRQS definition
  [ARM] 4679/1: AT91: Change maintainer email address
  [ARM] 4675/1: pxa: fix mfp address definition error for pxa320
  [ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
  [ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
  [ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
  [ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
  [ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
  [ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
  [ARM] uengine: fix memset size error
  [ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
  [ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
  [ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
  [ARM] 4604/2: AT91: Master clock divistor on SAM9
  [ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
  [ARM] PXA ssp: unlock when ssp tries to close an invalid port
  [ARM] 4654/1: pxa: update default MFP register value
  [ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
  [ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
  [ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions

The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON.  Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.

The call was added as part of commit ddc2e812
with the comment that "overhead should be minimal".  It may have been
minimal at the time, but it isn't now.

[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
  performance regression but rather the virt_to_head_page() changes to
  virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes iwl_mac_add_interface.

1. Currently only one interface is supported, instead of silently retuning
 0 now it returns  -EOPNOTSUPP (By Johannes Berg)
2. It enables changing mac address from user space (By Ian Schram)
Signed-off-by: Tomas Winkler <tomas@localhost.localdomain>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org
Cc: Ian Schram <ischram@telenet.be>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.

The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  x86 setup: don't recalculate ss:esp unless really necessary

If NR_IRQS is defined as a sum without surrounding parentheses, this may
lead to problems when used in multiplications. This may lead to problems
in:
arch/ia64/sn/kernel/irq.c:516
arch/x86/kernel/io_apic_32.c:693, 694, 699, 700
fs/proc/proc_misc.c:464
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Change email address of AT91 maintainer.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be
higher than default to cope with the fast PCLK frequency.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdio_uart: fix sign of paramter status in sdio_uart_receive_chars()

This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops.  This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.

Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
>   wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
>   pmd_large() and pmd_bad() is also indirectly involved.
>   __flush_tlb() and friends suffer, too.

Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway.  I don't think this is a
particularly good reason to reject the patch, for several reasons:

1. These operations are still available to modules when not using
   CONFIG_PARAVIRT, since they are implicitly exported as inline
   functions via the kernel headers.  Exporting the same functionality as
   GPL-only symbols just adds a gratuitious difference between
   CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations.  If we really
   think these operations are not for module use (or non-GPL module use),
   then we should solve the problem in a general way.

2. It's a regression from previous kernels, which would work these
   modules even with CONFIG_PARAVIRT enabled.

3. The operations in question seem pretty reasonable for modules to
   use.  The control registers/MSRs can be accessed directly anyway, so there's
   no benefit in preventing modules from using standard interfaces.  And it seems
   reasonable to allow a graphics driver to create its own mappings if it wants.

Therefore, I think this patch should go in for 2.6.24.  If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN.  Otherwise randconfigs with VISWS and LGUEST
have this problem:

In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
                 from include/asm/processor_32.h:17,
                 from include/asm/processor.h:2,
                 from include/asm/thread_info_32.h:16,
                 from include/asm/thread_info.h:2,
                 from include/linux/thread_info.h:21,
                 from include/linux/preempt.h:9,
                 from include/linux/spinlock.h:49,
                 from include/linux/seqlock.h:29,
                 from include/linux/time.h:8,
                 from include/linux/timex.h:57,
                 from include/linux/sched.h:53,
                 from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition

(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>