First attempt used #elifdef which is not a real directive.
Signed-off-by: Kevin Hilman <kevin@hilman.org>

2420 defconfig with MTD support.

Umm, I forgot to delete unused variable 'flags'. Once there lets kill all
warning about unused variables in omap code :)

Make smc91x work on H4

Tabified

Attached is a patch which does work.  I went ahead and cleaned up the
bypass table entry for PRCM VIII.  Before it was using a shared entry
which wasn't quite like a boot reset.

Fixed mach-omap2/clock.h formatting

The attached patch fixes a problem noticed when compiling the kernel
for the OSK 5912 board using default config:
make omap_osk_5912_defconfig
make uImage

Update H4 defconfig for MMC

Remove unnecesssary MMC debug printk

I see ATP and Transcend cards failing repeatedly in the card select command
(CMD7) due to illegal instruction after CMD2.  Doing an extra status inquiry
when leaving the card identification mode seems to fix this problem.
This bug occured when opening the mmc cover with mounted card inside and
closing the cover again. This will cause detection of any new cards in
the card detection mode and ATP and Transcend cards get confused.

I don't know why only ATP and Transcend have this problem and why
doing status inquiry helps.  Status inquiry command CMD13 is neutral
and is claimed to not chnage the card state in the MMC spec.
The order of commands must be CMD13 first, then CMD7.  CMD13 fails
also due to illegal instruction error after CMD2 but after this the
card is back to its senses.

If CMD7 is run first, and CMD13 once CMD7 is seen failing, this fails
to bring the card back to its senses.  Then the CMD7 fails repeatedly
due to command timeout before and after CMD13.

The attached patch does the extra probing in mmc_setup() during
low clock which is perhaps an overkill. One could do it also in
mmc_rescan() after switching back to higher clock.

Add MMC support for 24xx

Add support for 24xx Menelaus I2C PM chip. Based on TI's 2.6.9 code.

This patch cleans up i2c-omap.c more for inclusion in the mainline kernel,
and adds support for both I2C interfaces on OMAP 24xx.

Moved UART clock initialisation code from clock.c
to serial.c
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Beautify include order in system.h

Moved prcm.h to include, changed system.h to use it

Changed OMAP_GPIO_IRQ() macro to allow higher GPIO interrupts

Change h4 smc91x init to use mux api

Improved omap2 arch_reset code based on Richard's code

Below is patch fixing soft lockup in clocks. clockfw_lock is already
held in clk_set_rate when calling omap1_clk_set_rate, no need to lock it
again.

Flash support for OMAP24xx
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Flash support for OMAP24xx
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mux additions and clean-up for omap2

Reorganize system.h and make omap2 reboot work

Move omap2 IO defines

Set smc91x irqtype for H4

Do not try to change rate on omap2 if no speed found

Enable GPIO clocks for 24xx

OMAP specific parts of RMK's hardware.h and mach-types.h patch

Signed-off-by: Kevin Hilman <kevin@hilman.org>

Signed-off-by: Kevin Hilman <kevin@hilman.org>

Undo of accidental change of default compiler

Add clock framework for omap2.

Based on omap2 clock framework code by Richard Woodruff.