- 26 Apr, 2009 1 commit
-
-
Theodore Ts'o authored
Use a separate lock to protect the orphan list, so we can stop overloading the use of lock_super(). Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 01 May, 2009 1 commit
-
-
Theodore Ts'o authored
The function ext4_mark_recovery_complete() is called from two call paths: either (a) while mounting the filesystem, in which case there's no danger of any other CPU calling write_super() until the mount is completed, and (b) while remounting the filesystem read-write, in which case the fs core has already locked the superblock. This also allows us to take out a very vile unlock_super()/lock_super() pair in ext4_remount(). Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 25 Apr, 2009 1 commit
-
-
Theodore Ts'o authored
ext4_fill_super() is no longer called by read_super(), and it is no longer called with the superblock locked. The unlock_super()/lock_super() is no longer present, so this comment is entirely superfluous. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 01 May, 2009 4 commits
-
-
Theodore Ts'o authored
Ext4's on-line resizing adds a new block group and then, only at the last step adjusts s_groups_count. However, it's possible on SMP systems that another CPU could see the updated the s_group_count and not see the newly initialized data structures for the just-added block group. For this reason, it's important to insert a SMP read barrier after reading s_groups_count and before reading any (for example) the new block group descriptors allowed by the increased value of s_groups_count. Unfortunately, we rather blatently violate this locking protocol documented in fs/ext4/resize.c. Fortunately, (1) on-line resizes happen relatively rarely, and (2) it seems rare that the filesystem code will immediately try to use just-added block group before any memory ordering issues resolve themselves. So apparently problems here are relatively hard to hit, since ext3 has been vulnerable to the same issue for years with no one apparently complaining. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
Theodore Ts'o authored
By using a separate super_operations structure for filesystems that have and don't have journals, we can simply ext4_write_super() --- which is only needed when no journal is present --- and ext4_freeze(), ext4_unfreeze(), and ext4_sync_fs(), which are only needed when the journal is present. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
Theodore Ts'o authored
The s_dirt flag wasn't completely handled correctly, but it didn't really matter when journalling was enabled. It turns out that when ext4 runs without a journal, we don't clear s_dirt in places where we should have, with the result that the high-level write_super() function was writing the superblock when it wasn't necessary. So we fix this by making ext4_commit_super() clear the s_dirt flag, and removing many of the other places where s_dirt is manipulated. When journalling is enabled, the s_dirt flag might be left set more often, but s_dirt really doesn't matter when journalling is enabled. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
Theodore Ts'o authored
The ext4_commit_super() function took both a struct super_block * and a struct ext4_super_block *, but the struct ext4_super_block can be derived from the struct super_block. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 25 Apr, 2009 1 commit
-
-
Theodore Ts'o authored
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 28 Apr, 2009 1 commit
-
-
Theodore Ts'o authored
For very large filesystems, the s_flex_groups array can get quite big. For example, a filesystem that can be resized up to 16TB will have 8192 flex groups (assuming the default flex_bg size of 16), so the array is 96k, which is *very* marginal for kmalloc(). On the other hand, a 160GB filesystem without the resize_inode feature will only require 960 bytes. So we try to allocate the array first using kmalloc(), and if that fails, we'll try to use vmalloc() instead. Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 12 May, 2009 2 commits
-
-
Aneesh Kumar K.V authored
Setting BH_Unwritten buffer_heads as BH_Mapped avoids multiple (unnecessary) calls to get_block() during the call to the write(2) system call. Setting BH_Unwritten buffer heads as BH_Mapped requires that the writepages() functions can handle BH_Unwritten buffer_heads. After this commit, things work as follows: ext4_ext_get_block() returns unmapped, unwritten, buffer head when called with create = 0 for prealloc space. This makes sure we handle the read path and non-delayed allocation case correctly. Even though the buffer head is marked unmapped we have valid b_blocknr and b_bdev values in the buffer_head. ext4_da_get_block_prep() called for block resrevation will now return mapped, unwritten, new buffer_head for prealloc space. This avoids multiple calls to get_block() for write to same offset. By making such buffers as BH_New, we also assure that sub-block zeroing of buffered writes happens correctly. Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
Aneesh Kumar K.V authored
The BH_Delay and BH_Unwritten flags should never leak out to submit_bh(). So add some BUG_ON() checks to submit_bh so we can get a stack trace and determine how and why this might have happened. (Note that only XFS and ext4 use these buffer head flags, and XFS does not use submit_bh(). So this patch should only modify behavior for ext4.) Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Cc: linux-fsdevel@vger.kernel.org
-
- 13 May, 2009 1 commit
-
-
Aneesh Kumar K.V authored
These struct buffer_heads are allocated on the stack (and hence are initialized with stack garbage). They are only used to call a get_blocks() function, so that's mostly OK, but b_state must be initialized to be 0 so we don't have any unexpected BH_* flags set by accident, such as BH_Unwritten or BH_Delay. Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
-
- 03 Jun, 2009 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/pmac: Update PowerMac 32-bit defconfig
-
- 02 Jun, 2009 11 commits
-
-
Alan Cox authored
Ideally we should have a directory of drivers and a link to the 'active' driver. For now just show the first device which is effectively the existing semantics without a warning. This is an update on the original buggy patch that I then forgot to resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels fixed and submitted by Intel ... Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alan Cox authored
This matches Bartlomiej's patch for ide_pci_generic: c339dfdd In the libata case netcell has its own mini driver. I suspect this fix is actually only needed for some firmware revs but it does no harm either way. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup e1000: add missing length check to e1000 receive routine forcedeth: add phy_power_down parameter, leave phy powered up by default (v2) Bluetooth: Remove useless flush_work() causing lockdep warnings
-
git://oss.sgi.com/xfs/xfsLinus Torvalds authored
* 'for-linus' of git://oss.sgi.com/xfs/xfs: xfs: prevent deadlock in xfs_qm_shake() xfs: fix overflow in xfs_growfs_data_private xfs: fix double unlock in xfs_swap_extents()
-
Minoru Usui authored
net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup This patch fixes a bug which unconfigured struct tcf_proto keeps chaining in tc_ctl_tfilter(), and avoids kernel panic in cls_cgroup_classify() when we use cls_cgroup. When we execute 'tc filter add', tcf_proto is allocated, initialized by classifier's init(), and chained. After it's chained, tc_ctl_tfilter() calls classifier's change(). When classifier's change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto. In addition, cls_cgroup is initialized in change() not in init(). It accesses unconfigured struct tcf_proto which is chained before change(), then hits Oops. Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Neil Horman authored
Patch to fix bad length checking in e1000. E1000 by default does two things: 1) Spans rx descriptors for packets that don't fit into 1 skb on recieve 2) Strips the crc from a frame by subtracting 4 bytes from the length prior to doing an skb_put Since the e1000 driver isn't written to support receiving packets that span multiple rx buffers, it checks the End of Packet bit of every frame, and discards it if its not set. This places us in a situation where, if we have a spanning packet, the first part is discarded, but the second part is not (since it is the end of packet, and it passes the EOP bit test). If the second part of the frame is small (4 bytes or less), we subtract 4 from it to remove its crc, underflow the length, and wind up in skb_over_panic, when we try to skb_put a huge number of bytes into the skb. This amounts to a remote DOS attack through careful selection of frame size in relation to interface MTU. The fix for this is already in the e1000e driver, as well as the e1000 sourceforge driver, but no one ever pushed it to e1000. This is lifted straight from e1000e, and prevents small frames from causing the underflow described above Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ed Swierk authored
Add a phy_power_down parameter to forcedeth: set to 1 to power down the phy and disable the link when an interface goes down; set to 0 to always leave the phy powered up. The phy power state persists across reboots; Windows, some BIOSes, and older versions of Linux don't bother to power up the phy again, forcing users to remove all power to get the interface working (see http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy powered on is the safest default behavior. Users accustomed to seeing the link state reflect the interface state and/or wanting to minimize power consumption can set phy_power_down=1 if compatibility with other OSes is not an issue. Signed-off-by: Ed Swierk <eswierk@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Felix Blyakher authored
It's possible to recurse into filesystem from the memory allocation, which deadlocks in xfs_qm_shake(). Add check for __GFP_FS, and bail out if it is not set. Signed-off-by: Felix Blyakher <felixb@sgi.com> Signed-off-by: Hedi Berriche <hedi@sgi.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Eric Sandeen authored
In the case where growing a filesystem would leave the last AG too small, the fixup code has an overflow in the calculation of the new size with one fewer ag, because "nagcount" is a 32 bit number. If the new filesystem has > 2^32 blocks in it this causes a problem resulting in an EINVAL return from growfs: # xfs_io -f -c "truncate 19998630180864" fsfile # mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile # mount -o loop fsfile /mnt # xfs_growfs /mnt meta-data=/dev/loop0 isize=256 agcount=52, agsize=76288719 blks = sectsz=512 attr=2 data = bsize=4096 blocks=3905982455, imaxpct=5 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 log =internal bsize=4096 blocks=32768, version=2 = sectsz=512 sunit=0 blks, lazy-count=0 realtime =none extsz=4096 blocks=0, rtextents=0 xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument Reported-by: richard.ems@cape-horn-eng.com Signed-off-by: Eric Sandeen <sandeen@sandeen.net> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Felix Blyakher <felixb@sgi.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Felix Blyakher authored
Regreesion from commit ef8f7fc5, which rearranged the code in xfs_swap_extents() leading to double unlock of xfs inode ilock. That resulted in xfs_fsr deadlocking itself on platforms, which don't handle double unlock of rw_semaphore nicely. It caused the count go negative, which represents the write holder, without really having one. ia64 is one of the platforms where deadlock was easily reproduced and the fix was tested. Signed-off-by: Eric Sandeen <sandeen@sandeen.net> Reviewed-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Benjamin Herrenschmidt authored
This mostly adds back AppleTouch support and adds CONFIG_HIGHMEM by default. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
- 01 Jun, 2009 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: hash - Fix handling of sg entry that crosses page boundary
-
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/stagingLinus Torvalds authored
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: hwmon: Update documentation on fan_max hwmon: (lm78) Add missing __devexit_p()
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix section attribute warnings. sparc64: Fix SET_PERSONALITY to not clip bits outside of PER_MASK.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: 3c509: Add missing EISA IDs MAINTAINERS: take maintainership of the cpmac Ethernet driver net/firmare: Ignore .cis files ath1e: add new device id for asus hardware mlx4_en: Fix a kernel panic when waking tx queue rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan mac8390: fix build with NET_POLL_CONTROLLER cxgb3: link fault fixes cxgb3: fix dma mapping regression netfilter: nfnetlink_log: fix wrong skbuff size calculation netfilter: xt_hashlimit does a wrong SEQ_SKIP bfin_mac: fix build error due to net_device_ops convert atlx: move modinfo data from atlx.h to atl1.c gianfar: fix babbling rx error event bug cls_cgroup: read classid atomically in classifier netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache netfilter: nf_ct_tcp: fix accepting invalid RST segments
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6: headers_check fix: linux/net_dropmon.h headers_check fix: linux/auto_fs.h
-
Christian Engelmayer authored
Add fan_max description. Add fan limit alarm 'max_alarm' to the alarm section. Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
-
Mike Frysinger authored
The remove function uses __devexit, so the .remove assignment needs __devexit_p() to fix a build error with hotplug disabled. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
-
Maciej W. Rozycki authored
Several EISA device IDs for 3c509 family network cards are missing from the driver, making the cards unusable in their EISA mode. Here's a fix to add them based on the EISA configuration files distributed by 3Com and our eisa.ids database. Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
This patch adds me as the maintainer of the CPMAC (AR7) Ethernet driver. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jaswinder Singh Rajput authored
fix the following 'make headers_check' warnings: usr/include/linux/net_dropmon.h:7: found __[us]{8,16,32,64} type without #include <linux/types.h> Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
-
Jaswinder Singh Rajput authored
fix the following 'make headers_check' warnings: usr/include/linux/auto_fs.h:17: include of <linux/types.h> is preferred over <asm/types.h> Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
- 31 May, 2009 1 commit
-
-
Herbert Xu authored
A quirk that we've always supported is having an sg entry that's bigger than a page, or more generally an sg entry that crosses page boundaries. Even though it would be better to explicitly have to sg entries for this, we need to support it for the existing users, in particular, IPsec. The new ahash sg walking code did try to handle this, but there was a bug where we didn't increment the page so kept on walking on the first page over an dover again. This patch fixes it. Tested-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-
- 30 May, 2009 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: ide_pci_generic: add quirk for Netcell ATA RAID
-
Bartlomiej Zolnierkiewicz authored
We need to explicitly mark words 85-87 as valid ones since firmware doesn't do it. This should fix support for LBA48 and FLUSH CACHE [EXT] command which stopped working after we applied more strict checking of identify words in: commit 942dcd85 ("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()") and commit 4b58f17d ("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()") Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-