Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:

 - Only handle the number of GPIOs the chip actually has.  So
   for example on dm6467, GPIO-42 is the last GPIO, and trying
   to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.

 - Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
   previously, only the first five were enabled, so GPIO-80
   and above (on dm355) wouldn't trigger IRQs.

 - Use the right IRQ for each GPIO bank.  The wrong values were
   used for dm355 chips, so GPIO IRQs got routed incorrectly.

 - Handle up to four pairs of 16-bit GPIO banks ... previously
   only three were handled, so accessing GPIO-96 and up (e.g. on
   dm355) would oops.

 - Update several comments that were dm6446-specific.

Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.

One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs.  Some
bitmap logic could fix that if needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

During _omap3_noncore_dpll_lock(), if a DPLL has no active downstream
clocks and DPLL autoidle is enabled, the DPLL may never lock, since it
will enter autoidle immediately.  To resolve this, disable DPLL
autoidle while locking the DPLL, and unconditionally wait for the DPLL
to lock.  This fixes some bugs where the kernel would hang when returning
from retention or return the wrong rate for the DPLL.

This patch is a collaboration with Peter de Schrijver
<peter.de-schrijver@nokia.com> and Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DPLL FREQSEL jitter correction bits are set based on a table in
the 34xx TRM, Table 4-38, according to the DPLL's internal clock
frequency "Fint."  Several Fint frequency ranges are missing from this
table.  Previously, we allowed these Fint frequency ranges to be
selected in the rate rounding code, but did not change the FREQSEL bits.
Correspondence with the OMAP hardware team indicates that Fint values
not in the table should not be used.  So, prevent them from being
selected during DPLL rate rounding.  This removes warnings and also
can prevent the chip from locking up.

The first pass through the rate rounding code will update the DPLL max
and min dividers appropriately, so later rate rounding passes will run
faster than the first.

Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The previous DPLL rate rounding algorithm counted the divider (N) down
from the maximum to 1.  Since we currently use a broad DPLL rate
tolerance, and lower N values are more power-efficient, we can often
bypass several iterations through the loop by counting N upwards from
1.

Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove some clutter from omap2_dpll_round_rate().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This converts new files which are not yet merged upstream including
gpio-switch and board files for 3430sdp, Nokia N800 and omap3evm.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 41cc3cea.

Oops, my mistake, I was diffing wrong branches.
Signed-off-by: Tony Lindgren <tony@atomide.com>

I2C_WE registers were not configured, which caused huge delays in
I2C operations while cpu idle was enabled and omap entered WFI.

This patch enables all I2C wakeup sources.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The I2C controller clears its OCP_SYSCONFIG register after an OCP soft reset.
Reprogram OCP_SYSCONFIG for maximum power savings on rev3.6 controllers
and beyond.  On 2430, this involves setting the module AUTOIDLE bit.
On 3430, this includes module AUTOIDLE, wakeup enable, slave smart-idle,
and considers only the module functional clock state for idle-ack.

Boot-tested on 2430SDP and 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

i2c-omap discriminates only between "revision 1" or "greater than
revision 1."  A following patch introduces code that must also
discriminate between rev2.x, rev3.6, and rev3.12 controllers.  Support
this by storing the full revision data from the I2C_REV register, rather
than just a single bit.

The revision definitions may need to be extended for other ES levels
that aren't currently available here.  rev3.6 is what's present on the
2430SDP here (unknown ES revision); rev3.12 is used on the 3430ES2
here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Sync i2c-omap with patchesg going to mainline tree:

- Unify the clock naming for 242x and 243x
- Don't try to set a NULL pointer to 100
- Do a readback to flush posted write instead of wmb()
Signed-off-by: Tony Lindgren <tony@atomide.com>

This file got out of sync with the earlier strongly ordered patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>

The PCM3008 is used on the Lyrtech SFFSDR board, in conjunction with an
FPGA that generates the bit clock and the master clock
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The PCM3008 is a 16-bit stereo audio codec. It accepts
left-justified format for ADC, and right-justified format
for DAC. Independent power-down modes for ADC and DAC are
provided, as well as a digital de-emphasis filter (4 modes).
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix concurrent capture/playback issue.
The issue is caused by re-initialization of control registers used specifically
for capture or playback in both capture and playback operations.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branches 'master' and 'linus'

Add the /arch/arm/configs/davinci_sffsdr_defconfig file
for the Lyrtech SFFSDR board
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The Lyrtech SFFSDR (Small form Factor Software Defined Radio) board
is built around a TI DM6446 and a Xilinx Virtex-4 (SX-35) FPGA. This
patch adds basic board setup code for the SFFSDR.
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

- move UART register definitions to serial.h
- DM646x: move serial reset from board code to chip code
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] xen: fix xen_get_eflags.
  [IA64] ia64/pv_ops/pv_cpu_ops: fix _IA64_REG_IP case.
  [IA64] remove duplicate include iommu.h
  [IA64] use mprintk instead of printk, in ia64_mca_modify_original_stack
  [IA64] Rationalize kernel mode alignment checking

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: ACE1001 patch for cp2101.c
  USB: usbmon: fix read(2)
  USB: gadget rndis: send notifications
  USB: gadget rndis: stop windows self-immolation
  USB: storage: update unusual_devs entries for Nokia 5300 and 5310
  USB: storage: updates unusual_devs entry for the Nokia 6300
  usb: musb: fix bug in musb_schedule
  USB: fix SB700 usb subsystem hang bug

fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>

pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>

arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:

* Base kernel code ran in permissive mode where the only traps
  generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
  unaligned accesses caused traps to the 0x5a00 unaligned reference
  vector.

Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Signed-off-by: Tony Luck <tony.luck@intel.com>

When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used.  If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.

This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.

It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.

The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Do not attempt to close invalidated file handles
  [CIFS] fix check for dead tcon in smb_init