Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
  serial: Add driver for the Cell Network Processor serial port NWP device
  powerpc: enable dynamic ftrace
  powerpc/cell: Fix the prototype of create_vma_map()
  powerpc/mm: Make clear_fixmap() actually work
  powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
  powerpc: Export cacheable_memzero as its now used in a driver
  powerpc: Fix missing semicolons in mmu_decl.h
  powerpc/pasemi: local_irq_save uses an unsigned long
  powerpc/cell: Fix some u64 vs. long types
  powerpc/cell: Use correct types in beat files
  powerpc: Use correct type in prom_init.c
  powerpc: Remove unnecessary casts
  mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
  mtd/ps3vram: Use msleep in waits
  mtd/ps3vram: Use proper kernel types
  mtd/ps3vram: Cleanup ps3vram driver messages
  mtd/ps3vram: Remove ps3vram debug routines
  mtd/ps3vram: Add modalias support to the ps3vram driver
  mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
  powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
  ...

Documentation/powerpc/dts-bindings/fsl/board.txt

@@ -18,7 +18,7 @@ This is the memory-mapped registers for on board FPGA.
 
 Required properities:
 - compatible : should be "fsl,fpga-pixis".
-- reg : should contain the address and the lenght of the FPPGA register
+- reg : should contain the address and the length of the FPPGA register
   set.
 
 Example (MPC8610HPCD):
@@ -27,3 +27,33 @@ Example (MPC8610HPCD):
 		compatible = "fsl,fpga-pixis";
 		reg = <0xe8000000 32>;
 	};
+
+* Freescale BCSR GPIO banks
+
+Some BCSR registers act as simple GPIO controllers, each such
+register can be represented by the gpio-controller node.
+
+Required properities:
+- compatible : Should be "fsl,<board>-bcsr-gpio".
+- reg : Should contain the address and the length of the GPIO bank
+  register.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional paramters (currently unused).
+- gpio-controller : Marks the port as GPIO controller.
+
+Example:
+
+	bcsr@1,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8360mds-bcsr";
+		reg = <1 0 0x8000>;
+		ranges = <0 1 0 0x8000>;
+
+		bcsr13: gpio-controller@d {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8360mds-bcsr-gpio";
+			reg = <0xd 1>;
+			gpio-controller;
+		};
+	};

MAINTAINERS

@@ -3489,6 +3489,12 @@ L:	linuxppc-dev@ozlabs.org
 L:	cbe-oss-dev@ozlabs.org
 S:	Supported
 
+PS3VRAM DRIVER
+P:	Jim Paris
+M:	jim@jtan.com
+L:	cbe-oss-dev@ozlabs.org
+S:	Maintained
+
 PVRUSB2 VIDEO4LINUX DRIVER
 P:	Mike Isely
 M:	isely@pobox.com

arch/powerpc/Kconfig

@@ -108,6 +108,8 @@ config ARCH_NO_VIRT_TO_BUS
 config PPC
 	bool
 	default y
+	select HAVE_FTRACE_MCOUNT_RECORD
+	select HAVE_DYNAMIC_FTRACE
 	select HAVE_FUNCTION_TRACER
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select HAVE_IDE
@@ -326,7 +328,8 @@ config KEXEC
 
 config CRASH_DUMP
 	bool "Build a kdump crash kernel"
-	depends on (PPC64 && RELOCATABLE) || 6xx
+	depends on PPC64 || 6xx
+	select RELOCATABLE if PPC64
 	help
 	  Build a kernel suitable for use as a kdump capture kernel.
 	  The same kernel binary can be used as production kernel and dump

arch/powerpc/boot/Makefile

@@ -356,7 +356,7 @@ $(obj)/zImage.initrd:	$(addprefix $(obj)/, $(initrd-y))
 	@rm -f $@; ln $< $@
 
 install: $(CONFIGURE) $(addprefix $(obj)/, $(image-y))
-	sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $<
+	sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $^
 
 # anything not in $(targets)
 clean-files += $(image-) $(initrd-) cuImage.* dtbImage.* treeImage.* \

arch/powerpc/boot/dts/mpc836x_mds.dts

@@ -69,8 +69,18 @@
 		};
 
 		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
  			compatible = "fsl,mpc8360mds-bcsr";
 			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+
+			bcsr13: gpio-controller@d {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360mds-bcsr-gpio";
+				reg = <0xd 1>;
+				gpio-controller;
+			};
 		};
 	};
 
@@ -195,10 +205,21 @@
 		};
 
 		par_io@1400 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			reg = <0x1400 0x100>;
+			ranges = <0 0x1400 0x100>;
 			device_type = "par_io";
 			num-ports = <7>;
 
+			qe_pio_b: gpio-controller@18 {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360-qe-pario-bank",
+					     "fsl,mpc8323-qe-pario-bank";
+				reg = <0x18 0x18>;
+				gpio-controller;
+			};
+
 			pio1: ucc_pin@01 {
 				pio-map = <
 			/* port  pin  dir  open_drain  assignment  has_irq */
@@ -282,6 +303,15 @@
 			};
 		};
 
+		timer@440 {
+			compatible = "fsl,mpc8360-qe-gtm",
+				     "fsl,qe-gtm", "fsl,gtm";
+			reg = <0x440 0x40>;
+			clock-frequency = <132000000>;
+			interrupts = <12 13 14 15>;
+			interrupt-parent = <&qeic>;
+		};
+
 		spi@4c0 {
 			cell-index = <0>;
 			compatible = "fsl,spi";
@@ -301,11 +331,20 @@
 		};
 
 		usb@6c0 {
-			compatible = "qe_udc";
+			compatible = "fsl,mpc8360-qe-usb",
+				     "fsl,mpc8323-qe-usb";
 			reg = <0x6c0 0x40 0x8b00 0x100>;
 			interrupts = <11>;
 			interrupt-parent = <&qeic>;
-			mode = "slave";
+			fsl,fullspeed-clock = "clk21";
+			fsl,lowspeed-clock = "brg9";
+			gpios = <&qe_pio_b  2 0   /* USBOE */
+				 &qe_pio_b  3 0   /* USBTP */
+				 &qe_pio_b  8 0   /* USBTN */
+				 &qe_pio_b  9 0   /* USBRP */
+				 &qe_pio_b 11 0   /* USBRN */
+				 &bcsr13    5 0   /* SPEED */
+				 &bcsr13    4 1>; /* POWER */
 		};
 
 		enet0: ucc@2000 {

arch/powerpc/boot/dts/mpc836x_rdk.dts

@@ -218,8 +218,23 @@
 				reg = <0x440 0x40>;
 				interrupts = <12 13 14 15>;
 				interrupt-parent = <&qeic>;
-				/* filled by u-boot */
-				clock-frequency = <0>;
+				clock-frequency = <166666666>;
+			};
+
+			usb@6c0 {
+				compatible = "fsl,mpc8360-qe-usb",
+					     "fsl,mpc8323-qe-usb";
+				reg = <0x6c0 0x40 0x8b00 0x100>;
+				interrupts = <11>;
+				interrupt-parent = <&qeic>;
+				fsl,fullspeed-clock = "clk21";
+				gpios = <&qe_pio_b  2 0 /* USBOE */
+					 &qe_pio_b  3 0 /* USBTP */
+					 &qe_pio_b  8 0 /* USBTN */
+					 &qe_pio_b  9 0 /* USBRP */
+					 &qe_pio_b 11 0 /* USBRN */
+					 &qe_pio_e 20 0 /* SPEED */
+					 &qe_pio_e 21 1 /* POWER */>;
 			};
 
 			spi@4c0 {

arch/powerpc/boot/dts/mpc8641_hpcn.dts

@@ -26,7 +26,13 @@
 		serial1 = &serial1;
 		pci0 = &pci0;
 		pci1 = &pci1;
-		rapidio0 = &rapidio0;
+/*
+ * Only one of Rapid IO or PCI can be present due to HW limitations and
+ * due to the fact that the 2 now share address space in the new memory
+ * map.  The most likely case is that we have PCI, so comment out the
+ * rapidio node.  Leave it here for reference.
+ */
+		/* rapidio0 = &rapidio0; */
 	};
 
 	cpus {
@@ -62,18 +68,17 @@
 		reg = <0x00000000 0x40000000>;	// 1G at 0x0
 	};
 
-	localbus@f8005000 {
+	localbus@ffe05000 {
 		#address-cells = <2>;
 		#size-cells = <1>;
 		compatible = "fsl,mpc8641-localbus", "simple-bus";
-		reg = <0xf8005000 0x1000>;
+		reg = <0xffe05000 0x1000>;
 		interrupts = <19 2>;
 		interrupt-parent = <&mpic>;
 
-		ranges = <0 0 0xff800000 0x00800000
-			  1 0 0xfe000000 0x01000000
-			  2 0 0xf8200000 0x00100000
-			  3 0 0xf8100000 0x00100000>;
+		ranges = <0 0 0xef800000 0x00800000
+			  2 0 0xffdf8000 0x00008000
+			  3 0 0xffdf0000 0x00008000>;
 
 		flash@0,0 {
 			compatible = "cfi-flash";
@@ -103,13 +108,13 @@
 		};
 	};
 
-	soc8641@f8000000 {
+	soc8641@ffe00000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
 		compatible = "simple-bus";
-		ranges = <0x00000000 0xf8000000 0x00100000>;
-		reg = <0xf8000000 0x00001000>;	// CCSRBAR
+		ranges = <0x00000000 0xffe00000 0x00100000>;
+		reg = <0xffe00000 0x00001000>;	// CCSRBAR
 		bus-frequency = <0>;
 
 		i2c@3000 {
@@ -340,17 +345,17 @@
 		};
 	};
 
-	pci0: pcie@f8008000 {
+	pci0: pcie@ffe08000 {
 		cell-index = <0>;
 		compatible = "fsl,mpc8641-pcie";
 		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xf8008000 0x1000>;
+		reg = <0xffe08000 0x1000>;
 		bus-range = <0x0 0xff>;
 		ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x20000000
-			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+			  0x01000000 0x0 0x00000000 0xffc00000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <24 2>;
@@ -481,7 +486,7 @@
 
 				  0x01000000 0x0 0x00000000
 				  0x01000000 0x0 0x00000000
-				  0x0 0x00100000>;
+				  0x0 0x00010000>;
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
 				#size-cells = <2>;
@@ -491,7 +496,7 @@
 					  0x0 0x20000000
 					  0x01000000 0x0 0x00000000
 					  0x01000000 0x0 0x00000000
-					  0x0 0x00100000>;
+					  0x0 0x00010000>;
 				isa@1e {
 					device_type = "isa";
 					#interrupt-cells = <2>;
@@ -549,17 +554,17 @@
 
 	};
 
-	pci1: pcie@f8009000 {
+	pci1: pcie@ffe09000 {
 		cell-index = <1>;
 		compatible = "fsl,mpc8641-pcie";
 		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xf8009000 0x1000>;
+		reg = <0xffe09000 0x1000>;
 		bus-range = <0 0xff>;
 		ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
-			  0x01000000 0x0 0x00000000 0xe3000000 0x0 0x00100000>;
+			  0x01000000 0x0 0x00000000 0xffc10000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <25 2>;
@@ -582,18 +587,21 @@
 
 				  0x01000000 0x0 0x00000000
 				  0x01000000 0x0 0x00000000
-				  0x0 0x00100000>;
+				  0x0 0x00010000>;
 		};
 	};
-	rapidio0: rapidio@f80c0000 {
+/*
+	rapidio0: rapidio@ffec0000 {
 		#address-cells = <2>;
 		#size-cells = <2>;
 		compatible = "fsl,rapidio-delta";
-		reg = <0xf80c0000 0x20000>;
-		ranges = <0 0 0xc0000000 0 0x20000000>;
+		reg = <0xffec0000 0x20000>;
+		ranges = <0 0 0x80000000 0 0x20000000>;
 		interrupt-parent = <&mpic>;
-		/* err_irq bell_outb_irq bell_inb_irq
-			msg1_tx_irq msg1_rx_irq	msg2_tx_irq msg2_rx_irq */
+		// err_irq bell_outb_irq bell_inb_irq
+		//	msg1_tx_irq msg1_rx_irq	msg2_tx_irq msg2_rx_irq
 		interrupts = <48 2 49 2 50 2 53 2 54 2 55 2 56 2>;
 	};
+*/
+
 };

arch/powerpc/boot/install.sh

@@ -15,7 +15,7 @@
 #   $2 - kernel image file
 #   $3 - kernel map file
 #   $4 - default install path (blank if root directory)
-#   $5 - kernel boot file, the zImage
+#   $5 and more - kernel boot files; zImage*, uImage, cuImage.*, etc.
 #
 
 # User may have a custom install script
@@ -38,3 +38,15 @@ fi
 
 cat $2 > $4/$image_name
 cp $3 $4/System.map
+
+# Copy all the bootable image files
+path=$4
+shift 4
+while [ $# -ne 0 ]; do
+	image_name=`basename $1`
+	if [ -f $path/$image_name ]; then
+		mv $path/$image_name $path/$image_name.old
+	fi
+	cat $1 > $path/$image_name
+	shift
+done;

arch/powerpc/configs/85xx/mpc8572_ds_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc3
-# Sat Nov  8 12:40:13 2008
+# Linux kernel version: 2.6.28-rc8
+# Tue Dec 30 11:17:46 2008
 #
 # CONFIG_PPC64 is not set
 
@@ -21,7 +21,10 @@ CONFIG_FSL_BOOKE=y
 CONFIG_FSL_EMB_PERFMON=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_SPE=y
+CONFIG_PPC_MMU_NOHASH=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_SMP=y
+CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
 # CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
@@ -50,7 +53,7 @@ CONFIG_ARCH_MAY_HAVE_PC_FDC=y
 CONFIG_PPC_OF=y
 CONFIG_OF=y
 CONFIG_PPC_UDBG_16550=y
-# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
 CONFIG_DEFAULT_UIMAGE=y
@@ -62,7 +65,7 @@ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
 # General setup
 #
 CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
 CONFIG_INIT_ENV_ARG_LIMIT=32
 CONFIG_LOCALVERSION=""
 CONFIG_LOCALVERSION_AUTO=y
@@ -126,6 +129,7 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_USE_GENERIC_SMP_HELPERS=y
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
@@ -138,6 +142,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_KMOD=y
+CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
 CONFIG_LBD=y
 # CONFIG_BLK_DEV_IO_TRACE is not set
@@ -197,6 +202,7 @@ CONFIG_PPC_I8259=y
 # CONFIG_CPM2 is not set
 CONFIG_FSL_ULI1575=y
 # CONFIG_MPC8xxx_GPIO is not set
+# CONFIG_SIMPLE_GPIO is not set
 
 #
 # Kernel options
@@ -224,6 +230,7 @@ CONFIG_MATH_EMULATION=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+# CONFIG_IRQ_ALL_CPUS is not set
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_ARCH_POPULATES_NODE_MAP=y
 CONFIG_SELECT_MEMORY_MODEL=y
@@ -241,6 +248,9 @@ CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
 CONFIG_UNEVICTABLE_LRU=y
+CONFIG_PPC_4K_PAGES=y
+# CONFIG_PPC_16K_PAGES is not set
+# CONFIG_PPC_64K_PAGES is not set
 CONFIG_FORCE_MAX_ZONEORDER=11
 CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
@@ -443,8 +453,10 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_93CX6 is not set
 # CONFIG_SGI_IOC4 is not set
 # CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
 # CONFIG_HP_ILO is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -784,6 +796,7 @@ CONFIG_SERIAL_CORE_CONSOLE=y
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_HVC_UDBG is not set
 # CONFIG_IPMI_HANDLER is not set
 CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
@@ -869,11 +882,11 @@ CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_THERMAL is not set
 # CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
 
 #
 # Sonics Silicon Backplane
 #
-CONFIG_SSB_POSSIBLE=y
 # CONFIG_SSB is not set
 
 #
@@ -886,14 +899,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
-
-#
-# Voltage and Current regulators
-#
 # CONFIG_REGULATOR is not set
-# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
-# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
-# CONFIG_REGULATOR_BQ24022 is not set
 
 #
 # Multimedia devices
@@ -1252,11 +1258,11 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
 # CONFIG_USB_TMC is not set
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
 #
 
 #
-# may also be needed; see USB_STORAGE Help for more information
+# see USB_STORAGE Help for more information
 #
 CONFIG_USB_STORAGE=y
 # CONFIG_USB_STORAGE_DEBUG is not set
@@ -1348,6 +1354,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
 
 #
 # SPI RTC drivers
@@ -1624,6 +1631,7 @@ CONFIG_HAVE_FUNCTION_TRACER=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_DEBUG_PAGEALLOC is not set
@@ -1649,11 +1657,16 @@ CONFIG_CRYPTO=y
 #
 # CONFIG_CRYPTO_FIPS is not set
 CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
 CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
 CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
 CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
 CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
 # CONFIG_CRYPTO_GF128MUL is not set
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_CRYPTD is not set

arch/powerpc/include/asm/ioctls.h

@@ -89,6 +89,8 @@
 #define TIOCSBRK	0x5427  /* BSD compatibility */
 #define TIOCCBRK	0x5428  /* BSD compatibility */
 #define TIOCGSID	0x5429  /* Return the session ID of FD */
+#define TIOCGRS485	0x542e
+#define TIOCSRS485	0x542f
 #define TIOCGPTN	_IOR('T',0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
 #define TIOCSPTLCK	_IOW('T',0x31, int)  /* Lock/unlock Pty */
 

arch/powerpc/include/asm/kexec.h

@@ -48,63 +48,8 @@ static inline void crash_setup_regs(struct pt_regs *newregs,
 {
 	if (oldregs)
 		memcpy(newregs, oldregs, sizeof(*newregs));
-#ifdef __powerpc64__
-	else {
-		/* FIXME Merge this with xmon_save_regs ?? */
-		unsigned long tmp1, tmp2;
-		__asm__ __volatile__ (
-			"std    0,0(%2)\n"
-			"std    1,8(%2)\n"
-			"std    2,16(%2)\n"
-			"std    3,24(%2)\n"
-			"std    4,32(%2)\n"
-			"std    5,40(%2)\n"
-			"std    6,48(%2)\n"
-			"std    7,56(%2)\n"
-			"std    8,64(%2)\n"
-			"std    9,72(%2)\n"
-			"std    10,80(%2)\n"
-			"std    11,88(%2)\n"
-			"std    12,96(%2)\n"
-			"std    13,104(%2)\n"
-			"std    14,112(%2)\n"
-			"std    15,120(%2)\n"
-			"std    16,128(%2)\n"
-			"std    17,136(%2)\n"
-			"std    18,144(%2)\n"
-			"std    19,152(%2)\n"
-			"std    20,160(%2)\n"
-			"std    21,168(%2)\n"
-			"std    22,176(%2)\n"
-			"std    23,184(%2)\n"
-			"std    24,192(%2)\n"
-			"std    25,200(%2)\n"
-			"std    26,208(%2)\n"
-			"std    27,216(%2)\n"
-			"std    28,224(%2)\n"
-			"std    29,232(%2)\n"
-			"std    30,240(%2)\n"
-			"std    31,248(%2)\n"
-			"mfmsr  %0\n"
-			"std    %0, 264(%2)\n"
-			"mfctr  %0\n"
-			"std    %0, 280(%2)\n"
-			"mflr   %0\n"
-			"std    %0, 288(%2)\n"
-			"bl     1f\n"
-		"1:     mflr   %1\n"
-			"std    %1, 256(%2)\n"
-			"mtlr   %0\n"
-			"mfxer  %0\n"
-			"std    %0, 296(%2)\n"
-			: "=&r" (tmp1), "=&r" (tmp2)
-			: "b" (newregs)
-			: "memory");
-	}
-#else
 	else
 		ppc_save_regs(newregs);
-#endif /* __powerpc64__ */
 }
 
 extern void kexec_smp_wait(void);	/* get and clear naca physid, wait for

arch/powerpc/include/asm/ps3.h

@@ -320,6 +320,7 @@ enum ps3_match_id {
 
 enum ps3_match_sub_id {
 	PS3_MATCH_SUB_ID_GPU_FB		= 1,
+	PS3_MATCH_SUB_ID_GPU_RAMDISK	= 2,
 };
 
 #define PS3_MODULE_ALIAS_EHCI		"ps3:1:0"
@@ -332,6 +333,7 @@ enum ps3_match_sub_id {
 #define PS3_MODULE_ALIAS_STOR_FLASH	"ps3:8:0"
 #define PS3_MODULE_ALIAS_SOUND		"ps3:9:0"
 #define PS3_MODULE_ALIAS_GPU_FB		"ps3:10:1"
+#define PS3_MODULE_ALIAS_GPU_RAMDISK	"ps3:10:2"
 #define PS3_MODULE_ALIAS_LPM		"ps3:11:0"
 
 enum ps3_system_bus_device_type {

arch/powerpc/include/asm/qe.h

@@ -17,6 +17,8 @@
 #ifdef __KERNEL__
 
 #include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/err.h>
 #include <asm/cpm.h>
 #include <asm/immap_qe.h>
 
@@ -84,7 +86,11 @@ static inline bool qe_clock_is_brg(enum qe_clock clk)
 extern spinlock_t cmxgcr_lock;
 
 /* Export QE common operations */
+#ifdef CONFIG_QUICC_ENGINE
 extern void __init qe_reset(void);
+#else
+static inline void qe_reset(void) {}
+#endif
 
 /* QE PIO */
 #define QE_PIO_PINS 32
@@ -101,16 +107,43 @@ struct qe_pio_regs {
 #endif
 };
 
-extern int par_io_init(struct device_node *np);
-extern int par_io_of_config(struct device_node *np);
 #define QE_PIO_DIR_IN	2
 #define QE_PIO_DIR_OUT	1
 extern void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin,
 				int dir, int open_drain, int assignment,
 				int has_irq);
+#ifdef CONFIG_QUICC_ENGINE
+extern int par_io_init(struct device_node *np);
+extern int par_io_of_config(struct device_node *np);
 extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
 			     int assignment, int has_irq);
 extern int par_io_data_set(u8 port, u8 pin, u8 val);
+#else
+static inline int par_io_init(struct device_node *np) { return -ENOSYS; }
+static inline int par_io_of_config(struct device_node *np) { return -ENOSYS; }
+static inline int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
+		int assignment, int has_irq) { return -ENOSYS; }
+static inline int par_io_data_set(u8 port, u8 pin, u8 val) { return -ENOSYS; }
+#endif /* CONFIG_QUICC_ENGINE */
+
+/*
+ * Pin multiplexing functions.
+ */
+struct qe_pin;
+#ifdef CONFIG_QE_GPIO
+extern struct qe_pin *qe_pin_request(struct device_node *np, int index);
+extern void qe_pin_free(struct qe_pin *qe_pin);
+extern void qe_pin_set_gpio(struct qe_pin *qe_pin);
+extern void qe_pin_set_dedicated(struct qe_pin *pin);
+#else
+static inline struct qe_pin *qe_pin_request(struct device_node *np, int index)
+{
+	return ERR_PTR(-ENOSYS);
+}
+static inline void qe_pin_free(struct qe_pin *qe_pin) {}
+static inline void qe_pin_set_gpio(struct qe_pin *qe_pin) {}
+static inline void qe_pin_set_dedicated(struct qe_pin *pin) {}
+#endif /* CONFIG_QE_GPIO */
 
 /* QE internal API */
 int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input);

arch/powerpc/include/asm/qe_ic.h

@@ -17,6 +17,9 @@
 
 #include <linux/irq.h>
 
+struct device_node;
+struct qe_ic;
+
 #define NUM_OF_QE_IC_GROUPS	6
 
 /* Flags when we init the QE IC */
@@ -54,17 +57,27 @@ enum qe_ic_grp_id {
 	QE_IC_GRP_RISCB		/* QE interrupt controller RISC group B */
 };
 
+#ifdef CONFIG_QUICC_ENGINE
 void qe_ic_init(struct device_node *node, unsigned int flags,
 		void (*low_handler)(unsigned int irq, struct irq_desc *desc),
 		void (*high_handler)(unsigned int irq, struct irq_desc *desc));
+unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
+unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
+#else
+static inline void qe_ic_init(struct device_node *node, unsigned int flags,
+		void (*low_handler)(unsigned int irq, struct irq_desc *desc),
+		void (*high_handler)(unsigned int irq, struct irq_desc *desc))
+{}
+static inline unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
+{ return 0; }
+static inline unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
+{ return 0; }
+#endif /* CONFIG_QUICC_ENGINE */
+
 void qe_ic_set_highest_priority(unsigned int virq, int high);
 int qe_ic_set_priority(unsigned int virq, unsigned int priority);
 int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
 
-struct qe_ic;
-unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
-unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
-
 static inline void qe_ic_cascade_low_ipic(unsigned int irq,
 					  struct irq_desc *desc)
 {

arch/powerpc/include/asm/spu.h

@@ -128,7 +128,7 @@ struct spu {
 	int number;
 	unsigned int irqs[3];
 	u32 node;
-	u64 flags;
+	unsigned long flags;
 	u64 class_0_pending;
 	u64 class_0_dar;
 	u64 class_1_dar;

arch/powerpc/kernel/Makefile

@@ -29,7 +29,7 @@ endif
 obj-y				:= cputable.o ptrace.o syscalls.o \
 				   irq.o align.o signal_32.o pmc.o vdso.o \
 				   init_task.o process.o systbl.o idle.o \
-				   signal.o sysfs.o
+				   signal.o sysfs.o cacheinfo.o
 obj-y				+= vdso32/
 obj-$(CONFIG_PPC64)		+= setup_64.o sys_ppc32.o \
 				   signal_64.o ptrace32.o \

arch/powerpc/kernel/cacheinfo.h

+#ifndef _PPC_CACHEINFO_H
+#define _PPC_CACHEINFO_H
+
+/* These are just hooks for sysfs.c to use. */
+extern void cacheinfo_cpu_online(unsigned int cpu_id);
+extern void cacheinfo_cpu_offline(unsigned int cpu_id);
+
+#endif /* _PPC_CACHEINFO_H */

arch/powerpc/kernel/pci-common.c

@@ -16,7 +16,7 @@
  * 2 of the License, or (at your option) any later version.
  */
 
-#undef DEBUG
+#define DEBUG
 
 #include <linux/kernel.h>
 #include <linux/pci.h>
@@ -1356,6 +1356,63 @@ static void __init pcibios_allocate_resources(int pass)
 	}
 }
 
+static void __init pcibios_reserve_legacy_regions(struct pci_bus *bus)
+{
+	struct pci_controller *hose = pci_bus_to_host(bus);
+	resource_size_t	offset;
+	struct resource *res, *pres;
+	int i;
+
+	pr_debug("Reserving legacy ranges for domain %04x\n", pci_domain_nr(bus));
+
+	/* Check for IO */
+	if (!(hose->io_resource.flags & IORESOURCE_IO))
+		goto no_io;
+	offset = (unsigned long)hose->io_base_virt - _IO_BASE;
+	res = kzalloc(sizeof(struct resource), GFP_KERNEL);
+	BUG_ON(res == NULL);
+	res->name = "Legacy IO";
+	res->flags = IORESOURCE_IO;
+	res->start = offset;
+	res->end = (offset + 0xfff) & 0xfffffffful;
+	pr_debug("Candidate legacy IO: %pR\n", res);
+	if (request_resource(&hose->io_resource, res)) {
+		printk(KERN_DEBUG
+		       "PCI %04x:%02x Cannot reserve Legacy IO %pR\n",
+		       pci_domain_nr(bus), bus->number, res);
+		kfree(res);
+	}
+
+ no_io:
+	/* Check for memory */
+	offset = hose->pci_mem_offset;
+	pr_debug("hose mem offset: %016llx\n", (unsigned long long)offset);
+	for (i = 0; i < 3; i++) {
+		pres = &hose->mem_resources[i];
+		if (!(pres->flags & IORESOURCE_MEM))
+			continue;
+		pr_debug("hose mem res: %pR\n", pres);
+		if ((pres->start - offset) <= 0xa0000 &&
+		    (pres->end - offset) >= 0xbffff)
+			break;
+	}
+	if (i >= 3)
+		return;
+	res = kzalloc(sizeof(struct resource), GFP_KERNEL);
+	BUG_ON(res == NULL);
+	res->name = "Legacy VGA memory";
+	res->flags = IORESOURCE_MEM;
+	res->start = 0xa0000 + offset;
+	res->end = 0xbffff + offset;
+	pr_debug("Candidate VGA memory: %pR\n", res);
+	if (request_resource(pres, res)) {
+		printk(KERN_DEBUG
+		       "PCI %04x:%02x Cannot reserve VGA memory %pR\n",
+		       pci_domain_nr(bus), bus->number, res);
+		kfree(res);
+	}
+}
+
 void __init pcibios_resource_survey(void)
 {
 	struct pci_bus *b;
@@ -1371,6 +1428,18 @@ void __init pcibios_resource_survey(void)
 		pcibios_allocate_resources(1);
 	}
 
+	/* Before we start assigning unassigned resource, we try to reserve
+	 * the low IO area and the VGA memory area if they intersect the
+	 * bus available resources to avoid allocating things on top of them
+	 */
+	if (!(ppc_pci_flags & PPC_PCI_PROBE_ONLY)) {
+		list_for_each_entry(b, &pci_root_buses, node)
+			pcibios_reserve_legacy_regions(b);
+	}
+
+	/* Now, if the platform didn't decide to blindly trust the firmware,
+	 * we proceed to assigning things that were left unassigned
+	 */
 	if (!(ppc_pci_flags & PPC_PCI_PROBE_ONLY)) {
 		pr_debug("PCI: Assigning unassigned resouces...\n");
 		pci_assign_unassigned_resources();

arch/powerpc/kernel/pci_64.c

@@ -560,9 +560,14 @@ long sys_pciconfig_iobase(long which, unsigned long in_bus,
 	 * G5 machines... So when something asks for bus 0 io base
 	 * (bus 0 is HT root), we return the AGP one instead.
 	 */
-	if (machine_is_compatible("MacRISC4"))
-		if (in_bus == 0)
+	if (in_bus == 0 && machine_is_compatible("MacRISC4")) {
+		struct device_node *agp;
+
+		agp = of_find_compatible_node(NULL, NULL, "u3-agp");
+		if (agp)
 			in_bus = 0xf0;
+		of_node_put(agp);
+	}
 
 	/* That syscall isn't quite compatible with PCI domains, but it's
 	 * used on pre-domains setup. We return the first match

arch/powerpc/kernel/ppc_ksyms.c

@@ -165,6 +165,7 @@ EXPORT_SYMBOL(timer_interrupt);
 EXPORT_SYMBOL(irq_desc);
 EXPORT_SYMBOL(tb_ticks_per_jiffy);
 EXPORT_SYMBOL(cacheable_memcpy);
+EXPORT_SYMBOL(cacheable_memzero);
 #endif
 
 #ifdef CONFIG_PPC32

arch/powerpc/kernel/prom.c

@@ -824,11 +824,11 @@ static int __init early_init_dt_scan_chosen(unsigned long node,
 #endif
 
 #ifdef CONFIG_KEXEC
-	lprop = (u64*)of_get_flat_dt_prop(node, "linux,crashkernel-base", NULL);
+	lprop = of_get_flat_dt_prop(node, "linux,crashkernel-base", NULL);
 	if (lprop)
 		crashk_res.start = *lprop;
 
-	lprop = (u64*)of_get_flat_dt_prop(node, "linux,crashkernel-size", NULL);
+	lprop = of_get_flat_dt_prop(node, "linux,crashkernel-size", NULL);
 	if (lprop)
 		crashk_res.end = crashk_res.start + *lprop - 1;
 #endif
@@ -893,12 +893,12 @@ static int __init early_init_dt_scan_drconf_memory(unsigned long node)
 	u64 base, size, lmb_size;
 	unsigned int is_kexec_kdump = 0, rngs;
 
-	ls = (cell_t *)of_get_flat_dt_prop(node, "ibm,lmb-size", &l);
+	ls = of_get_flat_dt_prop(node, "ibm,lmb-size", &l);
 	if (ls == NULL || l < dt_root_size_cells * sizeof(cell_t))
 		return 0;
 	lmb_size = dt_mem_next_cell(dt_root_size_cells, &ls);
 
-	dm = (cell_t *)of_get_flat_dt_prop(node, "ibm,dynamic-memory", &l);
+	dm = of_get_flat_dt_prop(node, "ibm,dynamic-memory", &l);
 	if (dm == NULL || l < sizeof(cell_t))
 		return 0;
 
@@ -907,7 +907,7 @@ static int __init early_init_dt_scan_drconf_memory(unsigned long node)
 		return 0;
 
 	/* check if this is a kexec/kdump kernel. */
-	usm = (cell_t *)of_get_flat_dt_prop(node, "linux,drconf-usable-memory",
+	usm = of_get_flat_dt_prop(node, "linux,drconf-usable-memory",
 						 &l);
 	if (usm != NULL)
 		is_kexec_kdump = 1;
@@ -981,9 +981,9 @@ static int __init early_init_dt_scan_memory(unsigned long node,
 	} else if (strcmp(type, "memory") != 0)
 		return 0;
 
-	reg = (cell_t *)of_get_flat_dt_prop(node, "linux,usable-memory", &l);
+	reg = of_get_flat_dt_prop(node, "linux,usable-memory", &l);
 	if (reg == NULL)
-		reg = (cell_t *)of_get_flat_dt_prop(node, "reg", &l);
+		reg = of_get_flat_dt_prop(node, "reg", &l);
 	if (reg == NULL)
 		return 0;
 

arch/powerpc/kernel/prom_init.c

@@ -1210,7 +1210,7 @@ static void __init prom_initialize_tce_table(void)
 		/* Initialize the table to have a one-to-one mapping
 		 * over the allocated size.
 		 */
-		tce_entryp = (unsigned long *)base;
+		tce_entryp = (u64 *)base;
 		for (i = 0; i < (minsize >> 3) ;tce_entryp++, i++) {
 			tce_entry = (i << PAGE_SHIFT);
 			tce_entry |= 0x3;

arch/powerpc/kernel/sysfs.c

@@ -18,6 +18,8 @@
 #include <asm/machdep.h>
 #include <asm/smp.h>
 
+#include "cacheinfo.h"
+
 #ifdef CONFIG_PPC64
 #include <asm/paca.h>
 #include <asm/lppaca.h>
@@ -25,8 +27,6 @@
 
 static DEFINE_PER_CPU(struct cpu, cpu_devices);
 
-static DEFINE_PER_CPU(struct kobject *, cache_toplevel);
-
 /*
  * SMT snooze delay stuff, 64-bit only for now
  */
@@ -343,283 +343,6 @@ static struct sysdev_attribute pa6t_attrs[] = {
 #endif /* HAS_PPC_PMC_PA6T */
 #endif /* HAS_PPC_PMC_CLASSIC */
 
-struct cache_desc {
-	struct kobject kobj;
-	struct cache_desc *next;
-	const char *type;	/* Instruction, Data, or Unified */
-	u32 size;		/* total cache size in KB */
-	u32 line_size;		/* in bytes */
-	u32 nr_sets;		/* number of sets */
-	u32 level;		/* e.g. 1, 2, 3... */
-	u32 associativity;	/* e.g. 8-way... 0 is fully associative */
-};
-
-DEFINE_PER_CPU(struct cache_desc *, cache_desc);
-
-static struct cache_desc *kobj_to_cache_desc(struct kobject *k)
-{
-	return container_of(k, struct cache_desc, kobj);
-}
-
-static void cache_desc_release(struct kobject *k)
-{
-	struct cache_desc *desc = kobj_to_cache_desc(k);
-
-	pr_debug("%s: releasing %s\n", __func__, kobject_name(k));
-
-	if (desc->next)
-		kobject_put(&desc->next->kobj);
-
-	kfree(kobj_to_cache_desc(k));
-}
-
-static ssize_t cache_desc_show(struct kobject *k, struct attribute *attr, char *buf)
-{
-	struct kobj_attribute *kobj_attr;
-
-	kobj_attr = container_of(attr, struct kobj_attribute, attr);
-
-	return kobj_attr->show(k, kobj_attr, buf);
-}
-
-static struct sysfs_ops cache_desc_sysfs_ops = {
-	.show = cache_desc_show,
-};
-
-static struct kobj_type cache_desc_type = {
-	.release = cache_desc_release,
-	.sysfs_ops = &cache_desc_sysfs_ops,
-};
-
-static ssize_t cache_size_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%uK\n", cache->size);
-}
-
-static struct kobj_attribute cache_size_attr =
-	__ATTR(size, 0444, cache_size_show, NULL);
-
-static ssize_t cache_line_size_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%u\n", cache->line_size);
-}
-
-static struct kobj_attribute cache_line_size_attr =
-	__ATTR(coherency_line_size, 0444, cache_line_size_show, NULL);
-
-static ssize_t cache_nr_sets_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%u\n", cache->nr_sets);
-}
-
-static struct kobj_attribute cache_nr_sets_attr =
-	__ATTR(number_of_sets, 0444, cache_nr_sets_show, NULL);
-
-static ssize_t cache_type_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%s\n", cache->type);
-}
-
-static struct kobj_attribute cache_type_attr =
-	__ATTR(type, 0444, cache_type_show, NULL);
-
-static ssize_t cache_level_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%u\n", cache->level);
-}
-
-static struct kobj_attribute cache_level_attr =
-	__ATTR(level, 0444, cache_level_show, NULL);
-
-static ssize_t cache_assoc_show(struct kobject *k, struct kobj_attribute *attr, char *buf)
-{
-	struct cache_desc *cache = kobj_to_cache_desc(k);
-
-	return sprintf(buf, "%u\n", cache->associativity);
-}
-
-static struct kobj_attribute cache_assoc_attr =
-	__ATTR(ways_of_associativity, 0444, cache_assoc_show, NULL);
-
-struct cache_desc_info {
-	const char *type;
-	const char *size_prop;
-	const char *line_size_prop;
-	const char *nr_sets_prop;
-};
-
-/* PowerPC Processor binding says the [di]-cache-* must be equal on
- * unified caches, so just use d-cache properties. */
-static struct cache_desc_info ucache_info = {
-	.type = "Unified",
-	.size_prop = "d-cache-size",
-	.line_size_prop = "d-cache-line-size",
-	.nr_sets_prop = "d-cache-sets",
-};
-
-static struct cache_desc_info dcache_info = {
-	.type = "Data",
-	.size_prop = "d-cache-size",
-	.line_size_prop = "d-cache-line-size",
-	.nr_sets_prop = "d-cache-sets",
-};
-
-static struct cache_desc_info icache_info = {
-	.type = "Instruction",
-	.size_prop = "i-cache-size",
-	.line_size_prop = "i-cache-line-size",
-	.nr_sets_prop = "i-cache-sets",
-};
-
-static struct cache_desc * __cpuinit create_cache_desc(struct device_node *np, struct kobject *parent, int index, int level, struct cache_desc_info *info)
-{
-	const u32 *cache_line_size;
-	struct cache_desc *new;
-	const u32 *cache_size;
-	const u32 *nr_sets;
-	int rc;
-
-	new = kzalloc(sizeof(*new), GFP_KERNEL);
-	if (!new)
-		return NULL;
-
-	rc = kobject_init_and_add(&new->kobj, &cache_desc_type, parent,
-				  "index%d", index);
-	if (rc)
-		goto err;
-
-	/* type */
-	new->type = info->type;
-	rc = sysfs_create_file(&new->kobj, &cache_type_attr.attr);
-	WARN_ON(rc);
-
-	/* level */
-	new->level = level;
-	rc = sysfs_create_file(&new->kobj, &cache_level_attr.attr);
-	WARN_ON(rc);
-
-	/* size */
-	cache_size = of_get_property(np, info->size_prop, NULL);
-	if (cache_size) {
-		new->size = *cache_size / 1024;
-		rc = sysfs_create_file(&new->kobj,
-				       &cache_size_attr.attr);
-		WARN_ON(rc);
-	}
-
-	/* coherency_line_size */
-	cache_line_size = of_get_property(np, info->line_size_prop, NULL);
-	if (cache_line_size) {
-		new->line_size = *cache_line_size;
-		rc = sysfs_create_file(&new->kobj,
-				       &cache_line_size_attr.attr);
-		WARN_ON(rc);
-	}
-
-	/* number_of_sets */
-	nr_sets = of_get_property(np, info->nr_sets_prop, NULL);
-	if (nr_sets) {
-		new->nr_sets = *nr_sets;
-		rc = sysfs_create_file(&new->kobj,
-				       &cache_nr_sets_attr.attr);
-		WARN_ON(rc);
-	}
-
-	/* ways_of_associativity */
-	if (new->nr_sets == 1) {
-		/* fully associative */
-		new->associativity = 0;
-		goto create_assoc;
-	}
-
-	if (new->nr_sets && new->size && new->line_size) {
-		/* If we have values for all of these we can derive
-		 * the associativity. */
-		new->associativity =
-			((new->size * 1024) / new->nr_sets) / new->line_size;
-create_assoc:
-		rc = sysfs_create_file(&new->kobj,
-				       &cache_assoc_attr.attr);
-		WARN_ON(rc);
-	}
-
-	return new;
-err:
-	kfree(new);
-	return NULL;
-}
-
-static bool cache_is_unified(struct device_node *np)
-{
-	return of_get_property(np, "cache-unified", NULL);
-}
-
-static struct cache_desc * __cpuinit create_cache_index_info(struct device_node *np, struct kobject *parent, int index, int level)
-{
-	struct device_node *next_cache;
-	struct cache_desc *new, **end;
-
-	pr_debug("%s(node = %s, index = %d)\n", __func__, np->full_name, index);
-
-	if (cache_is_unified(np)) {
-		new = create_cache_desc(np, parent, index, level,
-					&ucache_info);
-	} else {
-		new = create_cache_desc(np, parent, index, level,
-					&dcache_info);
-		if (new) {
-			index++;
-			new->next = create_cache_desc(np, parent, index, level,
-						      &icache_info);
-		}
-	}
-	if (!new)
-		return NULL;
-
-	end = &new->next;
-	while (*end)
-		end = &(*end)->next;
-
-	next_cache = of_find_next_cache_node(np);
-	if (!next_cache)
-		goto out;
-
-	*end = create_cache_index_info(next_cache, parent, ++index, ++level);
-
-	of_node_put(next_cache);
-out:
-	return new;
-}
-
-static void __cpuinit create_cache_info(struct sys_device *sysdev)
-{
-	struct kobject *cache_toplevel;
-	struct device_node *np = NULL;
-	int cpu = sysdev->id;
-
-	cache_toplevel = kobject_create_and_add("cache", &sysdev->kobj);
-	if (!cache_toplevel)
-		return;
-	per_cpu(cache_toplevel, cpu) = cache_toplevel;
-	np = of_get_cpu_node(cpu, NULL);
-	if (np != NULL) {
-		per_cpu(cache_desc, cpu) =
-			create_cache_index_info(np, cache_toplevel, 0, 1);
-		of_node_put(np);
-	}
-	return;
-}
-
 static void __cpuinit register_cpu_online(unsigned int cpu)
 {
 	struct cpu *c = &per_cpu(cpu_devices, cpu);
@@ -684,25 +407,10 @@ static void __cpuinit register_cpu_online(unsigned int cpu)
 		sysdev_create_file(s, &attr_dscr);
 #endif /* CONFIG_PPC64 */
 
-	create_cache_info(s);
+	cacheinfo_cpu_online(cpu);
 }
 
 #ifdef CONFIG_HOTPLUG_CPU
-static void remove_cache_info(struct sys_device *sysdev)
-{
-	struct kobject *cache_toplevel;
-	struct cache_desc *cache_desc;
-	int cpu = sysdev->id;
-
-	cache_desc = per_cpu(cache_desc, cpu);
-	if (cache_desc != NULL)
-		kobject_put(&cache_desc->kobj);
-
-	cache_toplevel = per_cpu(cache_toplevel, cpu);
-	if (cache_toplevel != NULL)
-		kobject_put(cache_toplevel);
-}
-
 static void unregister_cpu_online(unsigned int cpu)
 {
 	struct cpu *c = &per_cpu(cpu_devices, cpu);
@@ -769,7 +477,7 @@ static void unregister_cpu_online(unsigned int cpu)
 		sysdev_remove_file(s, &attr_dscr);
 #endif /* CONFIG_PPC64 */
 
-	remove_cache_info(s);
+	cacheinfo_cpu_offline(cpu);
 }
 #endif /* CONFIG_HOTPLUG_CPU */
 

arch/powerpc/mm/mmu_decl.h

@@ -30,11 +30,11 @@
 #if defined(CONFIG_40x) || defined(CONFIG_8xx)
 static inline void _tlbil_all(void)
 {
-	asm volatile ("sync; tlbia; isync" : : : "memory")
+	asm volatile ("sync; tlbia; isync" : : : "memory");
 }
 static inline void _tlbil_pid(unsigned int pid)
 {
-	asm volatile ("sync; tlbia; isync" : : : "memory")
+	asm volatile ("sync; tlbia; isync" : : : "memory");
 }
 #else /* CONFIG_40x || CONFIG_8xx */
 extern void _tlbil_all(void);
@@ -47,7 +47,7 @@ extern void _tlbil_pid(unsigned int pid);
 #ifdef CONFIG_8xx
 static inline void _tlbil_va(unsigned long address, unsigned int pid)
 {
-	asm volatile ("tlbie %0; sync" : : "r" (address) : "memory")
+	asm volatile ("tlbie %0; sync" : : "r" (address) : "memory");
 }
 #else /* CONFIG_8xx */
 extern void _tlbil_va(unsigned long address, unsigned int pid);

arch/powerpc/mm/numa.c

@@ -822,42 +822,50 @@ static void __init dump_numa_memory_topology(void)
  * required. nid is the preferred node and end is the physical address of
  * the highest address in the node.
  *
- * Returns the physical address of the memory.
+ * Returns the virtual address of the memory.
  */
-static void __init *careful_allocation(int nid, unsigned long size,
+static void __init *careful_zallocation(int nid, unsigned long size,
 				       unsigned long align,
 				       unsigned long end_pfn)
 {
+	void *ret;
 	int new_nid;
-	unsigned long ret = __lmb_alloc_base(size, align, end_pfn << PAGE_SHIFT);
+	unsigned long ret_paddr;
+
+	ret_paddr = __lmb_alloc_base(size, align, end_pfn << PAGE_SHIFT);
 
 	/* retry over all memory */
-	if (!ret)
-		ret = __lmb_alloc_base(size, align, lmb_end_of_DRAM());
+	if (!ret_paddr)
+		ret_paddr = __lmb_alloc_base(size, align, lmb_end_of_DRAM());
 
-	if (!ret)
-		panic("numa.c: cannot allocate %lu bytes on node %d",
+	if (!ret_paddr)
+		panic("numa.c: cannot allocate %lu bytes for node %d",
 		      size, nid);
 
+	ret = __va(ret_paddr);
+
 	/*
-	 * If the memory came from a previously allocated node, we must
-	 * retry with the bootmem allocator.
+	 * We initialize the nodes in numeric order: 0, 1, 2...
+	 * and hand over control from the LMB allocator to the
+	 * bootmem allocator.  If this function is called for
+	 * node 5, then we know that all nodes <5 are using the
+	 * bootmem allocator instead of the LMB allocator.
+	 *
+	 * So, check the nid from which this allocation came
+	 * and double check to see if we need to use bootmem
+	 * instead of the LMB.  We don't free the LMB memory
+	 * since it would be useless.
 	 */
-	new_nid = early_pfn_to_nid(ret >> PAGE_SHIFT);
+	new_nid = early_pfn_to_nid(ret_paddr >> PAGE_SHIFT);
 	if (new_nid < nid) {
-		ret = (unsigned long)__alloc_bootmem_node(NODE_DATA(new_nid),
+		ret = __alloc_bootmem_node(NODE_DATA(new_nid),
 				size, align, 0);
 
-		if (!ret)
-			panic("numa.c: cannot allocate %lu bytes on node %d",
-			      size, new_nid);
-
-		ret = __pa(ret);
-
-		dbg("alloc_bootmem %lx %lx\n", ret, size);
+		dbg("alloc_bootmem %p %lx\n", ret, size);
 	}
 
-	return (void *)ret;
+	memset(ret, 0, size);
+	return ret;
 }
 
 static struct notifier_block __cpuinitdata ppc64_numa_nb = {
@@ -952,7 +960,7 @@ void __init do_init_bootmem(void)
 
 	for_each_online_node(nid) {
 		unsigned long start_pfn, end_pfn;
-		unsigned long bootmem_paddr;
+		void *bootmem_vaddr;
 		unsigned long bootmap_pages;
 
 		get_pfn_range_for_nid(nid, &start_pfn, &end_pfn);
@@ -964,11 +972,9 @@ void __init do_init_bootmem(void)
 		 * previous nodes' bootmem to be initialized and have
 		 * all reserved areas marked.
 		 */
-		NODE_DATA(nid) = careful_allocation(nid,
+		NODE_DATA(nid) = careful_zallocation(nid,
 					sizeof(struct pglist_data),
 					SMP_CACHE_BYTES, end_pfn);
-		NODE_DATA(nid) = __va(NODE_DATA(nid));
-		memset(NODE_DATA(nid), 0, sizeof(struct pglist_data));
 
   		dbg("node %d\n", nid);
 		dbg("NODE_DATA() = %p\n", NODE_DATA(nid));
@@ -984,20 +990,20 @@ void __init do_init_bootmem(void)
   		dbg("end_paddr = %lx\n", end_pfn << PAGE_SHIFT);
 
 		bootmap_pages = bootmem_bootmap_pages(end_pfn - start_pfn);
-		bootmem_paddr = (unsigned long)careful_allocation(nid,
+		bootmem_vaddr = careful_zallocation(nid,
 					bootmap_pages << PAGE_SHIFT,
 					PAGE_SIZE, end_pfn);
-		memset(__va(bootmem_paddr), 0, bootmap_pages << PAGE_SHIFT);
 
-		dbg("bootmap_paddr = %lx\n", bootmem_paddr);
+		dbg("bootmap_vaddr = %p\n", bootmem_vaddr);
 
-		init_bootmem_node(NODE_DATA(nid), bootmem_paddr >> PAGE_SHIFT,
+		init_bootmem_node(NODE_DATA(nid),
+				  __pa(bootmem_vaddr) >> PAGE_SHIFT,
 				  start_pfn, end_pfn);
 
 		free_bootmem_with_active_regions(nid, end_pfn);
 		/*
 		 * Be very careful about moving this around.  Future
-		 * calls to careful_allocation() depend on this getting
+		 * calls to careful_zallocation() depend on this getting
 		 * done correctly.
 		 */
 		mark_reserved_regions_for_nid(nid);

arch/powerpc/mm/pgtable_32.c

@@ -266,7 +266,8 @@ int map_page(unsigned long va, phys_addr_t pa, int flags)
 		/* The PTE should never be already set nor present in the
 		 * hash table
 		 */
-		BUG_ON(pte_val(*pg) & (_PAGE_PRESENT | _PAGE_HASHPTE));
+		BUG_ON((pte_val(*pg) & (_PAGE_PRESENT | _PAGE_HASHPTE)) &&
+		       flags);
 		set_pte_at(&init_mm, va, pg, pfn_pte(pa >> PAGE_SHIFT,
 						     __pgprot(flags)));
 	}

arch/powerpc/mm/tlb_nohash.c

@@ -189,8 +189,9 @@ void flush_tlb_kernel_range(unsigned long start, unsigned long end)
 	smp_call_function(do_flush_tlb_mm_ipi, NULL, 1);
 	_tlbil_pid(0);
 	preempt_enable();
-#endif
+#else
 	_tlbil_pid(0);
+#endif
 }
 EXPORT_SYMBOL(flush_tlb_kernel_range);
 

arch/powerpc/oprofile/cell/pr_util.h

@@ -79,7 +79,7 @@ struct spu_buffer {
  * the vma-to-fileoffset map.
  */
 struct vma_to_fileoffset_map *create_vma_map(const struct spu *spu,
-					     u64 objectid);
+					     unsigned long objectid);
 unsigned int vma_map_lookup(struct vma_to_fileoffset_map *map,
 			    unsigned int vma, const struct spu *aSpu,
 			    int *grd_val);

arch/powerpc/platforms/52xx/mpc52xx_common.c

@@ -42,7 +42,7 @@ static struct of_device_id mpc52xx_bus_ids[] __initdata = {
  * from interrupt context while node mapping (which calls ioremap())
  * cannot be used at such point.
  */
-static spinlock_t mpc52xx_lock = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(mpc52xx_lock);
 static struct mpc52xx_gpt __iomem *mpc52xx_wdt;
 static struct mpc52xx_cdm __iomem *mpc52xx_cdm;
 

arch/powerpc/platforms/83xx/mpc831x_rdb.c

@@ -42,7 +42,7 @@ static void __init mpc831x_rdb_setup_arch(void)
 	mpc831x_usb_cfg();
 }
 
-void __init mpc831x_rdb_init_IRQ(void)
+static void __init mpc831x_rdb_init_IRQ(void)
 {
 	struct device_node *np;
 

arch/powerpc/platforms/83xx/mpc832x_mds.c

@@ -49,8 +49,6 @@
 #define DBG(fmt...)
 #endif
 
-static u8 *bcsr_regs = NULL;
-
 /* ************************************************************************
  *
  * Setup the architecture
@@ -59,13 +57,14 @@ static u8 *bcsr_regs = NULL;
 static void __init mpc832x_sys_setup_arch(void)
 {
 	struct device_node *np;
+	u8 __iomem *bcsr_regs = NULL;
 
 	if (ppc_md.progress)
 		ppc_md.progress("mpc832x_sys_setup_arch()", 0);
 
 	/* Map BCSR area */
 	np = of_find_node_by_name(NULL, "bcsr");
-	if (np != 0) {
+	if (np) {
 		struct resource res;
 
 		of_address_to_resource(np, 0, &res);
@@ -93,9 +92,9 @@ static void __init mpc832x_sys_setup_arch(void)
 			!= NULL){
 		/* Reset the Ethernet PHYs */
 #define BCSR8_FETH_RST 0x50
-		bcsr_regs[8] &= ~BCSR8_FETH_RST;
+		clrbits8(&bcsr_regs[8], BCSR8_FETH_RST);
 		udelay(1000);
-		bcsr_regs[8] |= BCSR8_FETH_RST;
+		setbits8(&bcsr_regs[8], BCSR8_FETH_RST);
 		iounmap(bcsr_regs);
 		of_node_put(np);
 	}

arch/powerpc/platforms/83xx/mpc832x_rdb.c

@@ -38,6 +38,7 @@
 #define DBG(fmt...)
 #endif
 
+#ifdef CONFIG_QUICC_ENGINE
 static void mpc83xx_spi_activate_cs(u8 cs, u8 polarity)
 {
 	pr_debug("%s %d %d\n", __func__, cs, polarity);
@@ -77,8 +78,8 @@ static int __init mpc832x_spi_init(void)
 			    mpc83xx_spi_activate_cs,
 			    mpc83xx_spi_deactivate_cs);
 }
-
 machine_device_initcall(mpc832x_rdb, mpc832x_spi_init);
+#endif /* CONFIG_QUICC_ENGINE */
 
 /* ************************************************************************
  *
@@ -130,7 +131,7 @@ static int __init mpc832x_declare_of_platform_devices(void)
 }
 machine_device_initcall(mpc832x_rdb, mpc832x_declare_of_platform_devices);
 
-void __init mpc832x_rdb_init_IRQ(void)
+static void __init mpc832x_rdb_init_IRQ(void)
 {
 
 	struct device_node *np;

arch/powerpc/platforms/83xx/mpc836x_mds.c

@@ -18,6 +18,7 @@
 
 #include <linux/stddef.h>
 #include <linux/kernel.h>
+#include <linux/compiler.h>
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/reboot.h>
@@ -43,6 +44,7 @@
 #include <asm/udbg.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
+#include <sysdev/simple_gpio.h>
 #include <asm/qe.h>
 #include <asm/qe_ic.h>
 
@@ -55,8 +57,6 @@
 #define DBG(fmt...)
 #endif
 
-static u8 *bcsr_regs = NULL;
-
 /* ************************************************************************
  *
  * Setup the architecture
@@ -65,13 +65,14 @@ static u8 *bcsr_regs = NULL;
 static void __init mpc836x_mds_setup_arch(void)
 {
 	struct device_node *np;
+	u8 __iomem *bcsr_regs = NULL;
 
 	if (ppc_md.progress)
 		ppc_md.progress("mpc836x_mds_setup_arch()", 0);
 
 	/* Map BCSR area */
 	np = of_find_node_by_name(NULL, "bcsr");
-	if (np != 0) {
+	if (np) {
 		struct resource res;
 
 		of_address_to_resource(np, 0, &res);
@@ -93,6 +94,16 @@ static void __init mpc836x_mds_setup_arch(void)
 
 		for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;)
 			par_io_of_config(np);
+#ifdef CONFIG_QE_USB
+		/* Must fixup Par IO before QE GPIO chips are registered. */
+		par_io_config_pin(1,  2, 1, 0, 3, 0); /* USBOE  */
+		par_io_config_pin(1,  3, 1, 0, 3, 0); /* USBTP  */
+		par_io_config_pin(1,  8, 1, 0, 1, 0); /* USBTN  */
+		par_io_config_pin(1, 10, 2, 0, 3, 0); /* USBRXD */
+		par_io_config_pin(1,  9, 2, 1, 3, 0); /* USBRP  */
+		par_io_config_pin(1, 11, 2, 1, 3, 0); /* USBRN  */
+		par_io_config_pin(2, 20, 2, 0, 1, 0); /* CLK21  */
+#endif /* CONFIG_QE_USB */
 	}
 
 	if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
@@ -151,6 +162,70 @@ static int __init mpc836x_declare_of_platform_devices(void)
 }
 machine_device_initcall(mpc836x_mds, mpc836x_declare_of_platform_devices);
 
+#ifdef CONFIG_QE_USB
+static int __init mpc836x_usb_cfg(void)
+{
+	u8 __iomem *bcsr;
+	struct device_node *np;
+	const char *mode;
+	int ret = 0;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,mpc8360mds-bcsr");
+	if (!np)
+		return -ENODEV;
+
+	bcsr = of_iomap(np, 0);
+	of_node_put(np);
+	if (!bcsr)
+		return -ENOMEM;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,mpc8323-qe-usb");
+	if (!np) {
+		ret = -ENODEV;
+		goto err;
+	}
+
+#define BCSR8_TSEC1M_MASK	(0x3 << 6)
+#define BCSR8_TSEC1M_RGMII	(0x0 << 6)
+#define BCSR8_TSEC2M_MASK	(0x3 << 4)
+#define BCSR8_TSEC2M_RGMII	(0x0 << 4)
+	/*
+	 * Default is GMII (2), but we should set it to RGMII (0) if we use
+	 * USB (Eth PHY is in RGMII mode anyway).
+	 */
+	clrsetbits_8(&bcsr[8], BCSR8_TSEC1M_MASK | BCSR8_TSEC2M_MASK,
+			       BCSR8_TSEC1M_RGMII | BCSR8_TSEC2M_RGMII);
+
+#define BCSR13_USBMASK	0x0f
+#define BCSR13_nUSBEN	0x08 /* 1 - Disable, 0 - Enable			*/
+#define BCSR13_USBSPEED	0x04 /* 1 - Full, 0 - Low			*/
+#define BCSR13_USBMODE	0x02 /* 1 - Host, 0 - Function			*/
+#define BCSR13_nUSBVCC	0x01 /* 1 - gets VBUS, 0 - supplies VBUS 	*/
+
+	clrsetbits_8(&bcsr[13], BCSR13_USBMASK, BCSR13_USBSPEED);
+
+	mode = of_get_property(np, "mode", NULL);
+	if (mode && !strcmp(mode, "peripheral")) {
+		setbits8(&bcsr[13], BCSR13_nUSBVCC);
+		qe_usb_clock_set(QE_CLK21, 48000000);
+	} else {
+		setbits8(&bcsr[13], BCSR13_USBMODE);
+		/*
+		 * The BCSR GPIOs are used to control power and
+		 * speed of the USB transceiver. This is needed for
+		 * the USB Host only.
+		 */
+		simple_gpiochip_init("fsl,mpc8360mds-bcsr-gpio");
+	}
+
+	of_node_put(np);
+err:
+	iounmap(bcsr);
+	return ret;
+}
+machine_arch_initcall(mpc836x_mds, mpc836x_usb_cfg);
+#endif /* CONFIG_QE_USB */
+
 static void __init mpc836x_mds_init_IRQ(void)
 {
 	struct device_node *np;

arch/powerpc/platforms/83xx/mpc836x_rdk.c

@@ -51,8 +51,9 @@ static void __init mpc836x_rdk_setup_arch(void)
 	for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
 		mpc83xx_add_bridge(np);
 #endif
-
+#ifdef CONFIG_QUICC_ENGINE
 	qe_reset();
+#endif
 }
 
 static void __init mpc836x_rdk_init_IRQ(void)
@@ -71,13 +72,14 @@ static void __init mpc836x_rdk_init_IRQ(void)
 	 */
 	ipic_set_default_priority();
 	of_node_put(np);
-
+#ifdef CONFIG_QUICC_ENGINE
 	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
 	if (!np)
 		return;
 
 	qe_ic_init(np, 0, qe_ic_cascade_low_ipic, qe_ic_cascade_high_ipic);
 	of_node_put(np);
+#endif
 }
 
 /*

arch/powerpc/platforms/83xx/mpc837x_mds.c

@@ -26,7 +26,6 @@
 #define BCSR12_USB_SER_MASK	0x8a
 #define BCSR12_USB_SER_PIN	0x80
 #define BCSR12_USB_SER_DEVICE	0x02
-extern int mpc837x_usb_cfg(void);
 
 static int mpc837xmds_usb_cfg(void)
 {

arch/powerpc/platforms/83xx/mpc837x_rdb.c

@@ -21,8 +21,6 @@
 
 #include "mpc83xx.h"
 
-extern int mpc837x_usb_cfg(void);
-
 /* ************************************************************************
  *
  * Setup the architecture

arch/powerpc/platforms/83xx/mpc83xx.h

@@ -61,6 +61,7 @@
 
 extern void mpc83xx_restart(char *cmd);
 extern long mpc83xx_time_init(void);
+extern int mpc837x_usb_cfg(void);
 extern int mpc834x_usb_cfg(void);
 extern int mpc831x_usb_cfg(void);
 

arch/powerpc/platforms/85xx/mpc85xx_ds.c

@@ -148,6 +148,9 @@ static int mpc85xx_exclude_device(struct pci_controller *hose,
 /*
  * Setup the architecture
  */
+#ifdef CONFIG_SMP
+extern void __init mpc85xx_smp_init(void);
+#endif
 static void __init mpc85xx_ds_setup_arch(void)
 {
 #ifdef CONFIG_PCI
@@ -173,6 +176,10 @@ static void __init mpc85xx_ds_setup_arch(void)
 	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
 #endif
 
+#ifdef CONFIG_SMP
+	mpc85xx_smp_init();
+#endif
+
 	printk("MPC85xx DS board from Freescale Semiconductor\n");
 }
 

arch/powerpc/platforms/85xx/smp.c

@@ -58,6 +58,7 @@ smp_85xx_kick_cpu(int nr)
 
 	if (cpu_rel_addr == NULL) {
 		printk(KERN_ERR "No cpu-release-addr for cpu %d\n", nr);
+		local_irq_restore(flags);
 		return;
 	}
 

arch/powerpc/platforms/Kconfig

@@ -312,4 +312,15 @@ config MPC8xxx_GPIO
 	  Say Y here if you're going to use hardware that connects to the
 	  MPC831x/834x/837x/8572/8610 GPIOs.
 
+config SIMPLE_GPIO
+	bool "Support for simple, memory-mapped GPIO controllers"
+	depends on PPC
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	  Say Y here to support simple, memory-mapped GPIO controllers.
+	  These are usually BCSRs used to control board's switches, LEDs,
+	  chip-selects, Ethernet/USB PHY's power and various other small
+	  on-board peripherals.
+
 endmenu

arch/powerpc/platforms/Kconfig.cputype

@@ -231,7 +231,7 @@ config VIRT_CPU_ACCOUNTING
 	  If in doubt, say Y here.
 
 config SMP
-	depends on PPC_STD_MMU
+	depends on PPC_STD_MMU || FSL_BOOKE
 	bool "Symmetric multi-processing support"
 	---help---
 	  This enables support for systems with more than one CPU. If you have

arch/powerpc/platforms/cell/beat_htab.c

@@ -44,8 +44,8 @@ static DEFINE_SPINLOCK(beat_htab_lock);
 
 static inline unsigned int beat_read_mask(unsigned hpte_group)
 {
-	unsigned long hpte_v[5];
 	unsigned long rmask = 0;
+	u64 hpte_v[5];
 
 	beat_read_htab_entries(0, hpte_group + 0, hpte_v);
 	if (!(hpte_v[0] & HPTE_V_BOLTED))
@@ -93,8 +93,7 @@ static long beat_lpar_hpte_insert(unsigned long hpte_group,
 				  int psize, int ssize)
 {
 	unsigned long lpar_rc;
-	unsigned long slot;
-	unsigned long hpte_v, hpte_r;
+	u64 hpte_v, hpte_r, slot;
 
 	/* same as iseries */
 	if (vflags & HPTE_V_SECONDARY)
@@ -153,8 +152,9 @@ static long beat_lpar_hpte_remove(unsigned long hpte_group)
 
 static unsigned long beat_lpar_hpte_getword0(unsigned long slot)
 {
-	unsigned long dword0, dword[5];
+	unsigned long dword0;
 	unsigned long lpar_rc;
+	u64 dword[5];
 
 	lpar_rc = beat_read_htab_entries(0, slot & ~3UL, dword);
 
@@ -170,7 +170,7 @@ static void beat_lpar_hptab_clear(void)
 	unsigned long size_bytes = 1UL << ppc64_pft_size;
 	unsigned long hpte_count = size_bytes >> 4;
 	int i;
-	unsigned long dummy0, dummy1;
+	u64 dummy0, dummy1;
 
 	/* TODO: Use bulk call */
 	for (i = 0; i < hpte_count; i++)
@@ -189,7 +189,8 @@ static long beat_lpar_hpte_updatepp(unsigned long slot,
 				    int psize, int ssize, int local)
 {
 	unsigned long lpar_rc;
-	unsigned long dummy0, dummy1, want_v;
+	u64 dummy0, dummy1;
+	unsigned long want_v;
 
 	want_v = hpte_encode_v(va, psize, MMU_SEGSIZE_256M);
 
@@ -255,7 +256,8 @@ static void beat_lpar_hpte_updateboltedpp(unsigned long newpp,
 					  unsigned long ea,
 					  int psize, int ssize)
 {
-	unsigned long lpar_rc, slot, vsid, va, dummy0, dummy1;
+	unsigned long lpar_rc, slot, vsid, va;
+	u64 dummy0, dummy1;
 
 	vsid = get_kernel_vsid(ea, MMU_SEGSIZE_256M);
 	va = (vsid << 28) | (ea & 0x0fffffff);
@@ -276,7 +278,7 @@ static void beat_lpar_hpte_invalidate(unsigned long slot, unsigned long va,
 {
 	unsigned long want_v;
 	unsigned long lpar_rc;
-	unsigned long dummy1, dummy2;
+	u64 dummy1, dummy2;
 	unsigned long flags;
 
 	DBG_LOW("    inval : slot=%lx, va=%016lx, psize: %d, local: %d\n",
@@ -315,8 +317,7 @@ static long beat_lpar_hpte_insert_v3(unsigned long hpte_group,
 				  int psize, int ssize)
 {
 	unsigned long lpar_rc;
-	unsigned long slot;
-	unsigned long hpte_v, hpte_r;
+	u64 hpte_v, hpte_r, slot;
 
 	/* same as iseries */
 	if (vflags & HPTE_V_SECONDARY)

arch/powerpc/platforms/cell/beat_udbg.c

@@ -40,8 +40,8 @@ static void udbg_putc_beat(char c)
 }
 
 /* Buffered chars getc */
-static long inbuflen;
-static long inbuf[2];	/* must be 2 longs */
+static u64 inbuflen;
+static u64 inbuf[2];	/* must be 2 u64s */
 
 static int udbg_getc_poll_beat(void)
 {

arch/powerpc/platforms/cell/cbe_cpufreq_pervasive.c

@@ -54,7 +54,7 @@ int cbe_cpufreq_set_pmode(int cpu, unsigned int pmode)
 {
 	struct cbe_pmd_regs __iomem *pmd_regs;
 	struct cbe_mic_tm_regs __iomem *mic_tm_regs;
-	u64 flags;
+	unsigned long flags;
 	u64 value;
 #ifdef DEBUG
 	long time;

arch/powerpc/platforms/cell/interrupt.c

@@ -148,7 +148,7 @@ static unsigned int iic_get_irq(void)
 
 	iic = &__get_cpu_var(iic);
 	*(unsigned long *) &pending =
-		in_be64((unsigned long __iomem *) &iic->regs->pending_destr);
+		in_be64((u64 __iomem *) &iic->regs->pending_destr);
 	if (!(pending.flags & CBE_IIC_IRQ_VALID))
 		return NO_IRQ;
 	virq = irq_linear_revmap(iic_host, iic_pending_to_hwnum(pending));

arch/powerpc/platforms/cell/io-workarounds.c

@@ -130,14 +130,14 @@ static const struct ppc_pci_io __devinitconst iowa_pci_io = {
 
 };
 
-static void __iomem *iowa_ioremap(unsigned long addr, unsigned long size,
+static void __iomem *iowa_ioremap(phys_addr_t addr, unsigned long size,
 						unsigned long flags)
 {
 	struct iowa_bus *bus;
 	void __iomem *res = __ioremap(addr, size, flags);
 	int busno;
 
-	bus = iowa_pci_find(0, addr);
+	bus = iowa_pci_find(0, (unsigned long)addr);
 	if (bus != NULL) {
 		busno = bus - iowa_busses;
 		PCI_SET_ADDR_TOKEN(res, busno + 1);

arch/powerpc/platforms/cell/iommu.c

@@ -150,8 +150,8 @@ static int cbe_nr_iommus;
 static void invalidate_tce_cache(struct cbe_iommu *iommu, unsigned long *pte,
 		long n_ptes)
 {
-	unsigned long __iomem *reg;
-	unsigned long val;
+	u64 __iomem *reg;
+	u64 val;
 	long n;
 
 	reg = iommu->xlate_regs + IOC_IOPT_CacheInvd;

arch/powerpc/platforms/iseries/Kconfig

@@ -10,18 +10,21 @@ menu "iSeries device drivers"
 config VIODASD
 	tristate "iSeries Virtual I/O disk support"
 	depends on BLOCK
+	select VIOPATH
 	help
 	  If you are running on an iSeries system and you want to use
 	  virtual disks created and managed by OS/400, say Y.
 
 config VIOCD
 	tristate "iSeries Virtual I/O CD support"
+	select VIOPATH
 	help
 	  If you are running Linux on an IBM iSeries system and you want to
 	  read a CD drive owned by OS/400, say Y here.
 
 config VIOTAPE
 	tristate "iSeries Virtual Tape Support"
+	select VIOPATH
 	help
 	  If you are running Linux on an iSeries system and you want Linux
 	  to read and/or write a tape drive owned by OS/400, say Y here.
@@ -30,5 +33,3 @@ endmenu
 
 config VIOPATH
 	bool
-	depends on VIODASD || VIOCD || VIOTAPE || ISERIES_VETH
-	default y

arch/powerpc/platforms/iseries/setup.c

@@ -23,6 +23,7 @@
 #include <linux/string.h>
 #include <linux/seq_file.h>
 #include <linux/kdev_t.h>
+#include <linux/kexec.h>
 #include <linux/major.h>
 #include <linux/root_dev.h>
 #include <linux/kernel.h>
@@ -638,6 +639,13 @@ static int __init iseries_probe(void)
 	return 1;
 }
 
+#ifdef CONFIG_KEXEC
+static int iseries_kexec_prepare(struct kimage *image)
+{
+	return -ENOSYS;
+}
+#endif
+
 define_machine(iseries) {
 	.name			= "iSeries",
 	.setup_arch		= iSeries_setup_arch,
@@ -658,6 +666,9 @@ define_machine(iseries) {
 	.probe			= iseries_probe,
 	.ioremap		= iseries_ioremap,
 	.iounmap		= iseries_iounmap,
+#ifdef CONFIG_KEXEC
+	.machine_kexec_prepare	= iseries_kexec_prepare,
+#endif
 	/* XXX Implement enable_pmcs for iSeries */
 };
 

arch/powerpc/platforms/pasemi/cpufreq.c

@@ -112,7 +112,7 @@ static int get_gizmo_latency(void)
 
 static void set_astate(int cpu, unsigned int astate)
 {
-	u64 flags;
+	unsigned long flags;
 
 	/* Return if called before init has run */
 	if (unlikely(!sdcasr_mapbase))

arch/powerpc/platforms/pasemi/dma_lib.c

@@ -509,7 +509,7 @@ fallback:
  */
 int pasemi_dma_init(void)
 {
-	static spinlock_t init_lock = SPIN_LOCK_UNLOCKED;
+	static DEFINE_SPINLOCK(init_lock);
 	struct pci_dev *iob_pdev;
 	struct pci_dev *pdev;
 	struct resource res;

arch/powerpc/platforms/powermac/pci.c

@@ -661,6 +661,7 @@ static void __init init_second_ohare(void)
 			pci_find_hose_for_OF_device(np);
 		if (!hose) {
 			printk(KERN_ERR "Can't find PCI hose for OHare2 !\n");
+			of_node_put(np);
 			return;
 		}
 		early_read_config_word(hose, bus, devfn, PCI_COMMAND, &cmd);
@@ -669,6 +670,7 @@ static void __init init_second_ohare(void)
 		early_write_config_word(hose, bus, devfn, PCI_COMMAND, cmd);
 	}
 	has_second_ohare = 1;
+	of_node_put(np);
 }
 
 /*

arch/powerpc/platforms/powermac/time.c

@@ -265,12 +265,15 @@ int __init via_calibrate_decr(void)
 	struct resource rsrc;
 
 	vias = of_find_node_by_name(NULL, "via-cuda");
-	if (vias == 0)
+	if (vias == NULL)
 		vias = of_find_node_by_name(NULL, "via-pmu");
-	if (vias == 0)
+	if (vias == NULL)
 		vias = of_find_node_by_name(NULL, "via");
-	if (vias == 0 || of_address_to_resource(vias, 0, &rsrc))
+	if (vias == NULL || of_address_to_resource(vias, 0, &rsrc)) {
+	        of_node_put(vias);
 		return 0;
+	}
+	of_node_put(vias);
 	via = ioremap(rsrc.start, rsrc.end - rsrc.start + 1);
 	if (via == NULL) {
 		printk(KERN_ERR "Failed to map VIA for timer calibration !\n");
@@ -297,7 +300,7 @@ int __init via_calibrate_decr(void)
 	ppc_tb_freq = (dstart - dend) * 100 / 6;
 
 	iounmap(via);
-	
+
 	return 1;
 }
 #endif

arch/powerpc/platforms/ps3/device-init.c

@@ -518,6 +518,41 @@ fail_device_register:
 	return result;
 }
 
+static int __init ps3_register_ramdisk_device(void)
+{
+	int result;
+	struct layout {
+		struct ps3_system_bus_device dev;
+	} *p;
+
+	pr_debug(" -> %s:%d\n", __func__, __LINE__);
+
+	p = kzalloc(sizeof(struct layout), GFP_KERNEL);
+
+	if (!p)
+		return -ENOMEM;
+
+	p->dev.match_id = PS3_MATCH_ID_GPU;
+	p->dev.match_sub_id = PS3_MATCH_SUB_ID_GPU_RAMDISK;
+	p->dev.dev_type = PS3_DEVICE_TYPE_IOC0;
+
+	result = ps3_system_bus_device_register(&p->dev);
+
+	if (result) {
+		pr_debug("%s:%d ps3_system_bus_device_register failed\n",
+			__func__, __LINE__);
+		goto fail_device_register;
+	}
+
+	pr_debug(" <- %s:%d\n", __func__, __LINE__);
+	return 0;
+
+fail_device_register:
+	kfree(p);
+	pr_debug(" <- %s:%d failed\n", __func__, __LINE__);
+	return result;
+}
+
 /**
  * ps3_setup_dynamic_device - Setup a dynamic device from the repository
  */
@@ -946,6 +981,8 @@ static int __init ps3_register_devices(void)
 
 	ps3_register_lpm_devices();
 
+	ps3_register_ramdisk_device();
+
 	pr_debug(" <- %s:%d\n", __func__, __LINE__);
 	return 0;
 }

arch/powerpc/sysdev/Makefile

@@ -17,6 +17,7 @@ obj-$(CONFIG_FSL_PCI)		+= fsl_pci.o $(fsl-msi-obj-y)
 obj-$(CONFIG_FSL_LBC)		+= fsl_lbc.o
 obj-$(CONFIG_FSL_GTM)		+= fsl_gtm.o
 obj-$(CONFIG_MPC8xxx_GPIO)	+= mpc8xxx_gpio.o
+obj-$(CONFIG_SIMPLE_GPIO)	+= simple_gpio.o
 obj-$(CONFIG_RAPIDIO)		+= fsl_rio.o
 obj-$(CONFIG_TSI108_BRIDGE)	+= tsi108_pci.o tsi108_dev.o
 obj-$(CONFIG_QUICC_ENGINE)	+= qe_lib/

arch/powerpc/sysdev/fsl_pci.c

@@ -29,7 +29,8 @@
 
 #if defined(CONFIG_PPC_85xx) || defined(CONFIG_PPC_86xx)
 /* atmu setup for fsl pci/pcie controller */
-void __init setup_pci_atmu(struct pci_controller *hose, struct resource *rsrc)
+static void __init setup_pci_atmu(struct pci_controller *hose,
+				  struct resource *rsrc)
 {
 	struct ccsr_pci __iomem *pci;
 	int i;
@@ -86,7 +87,7 @@ void __init setup_pci_atmu(struct pci_controller *hose, struct resource *rsrc)
 	out_be32(&pci->piw[2].piwar, PIWAR_2G);
 }
 
-void __init setup_pci_cmd(struct pci_controller *hose)
+static void __init setup_pci_cmd(struct pci_controller *hose)
 {
 	u16 cmd;
 	int cap_x;
@@ -130,7 +131,7 @@ static void __init quirk_fsl_pcie_header(struct pci_dev *dev)
 	return ;
 }
 
-int __init fsl_pcie_check_link(struct pci_controller *hose)
+static int __init fsl_pcie_check_link(struct pci_controller *hose)
 {
 	u32 val;
 	early_read_config_dword(hose, 0, 0, PCIE_LTSSM, &val);

arch/powerpc/sysdev/fsl_soc.h

@@ -5,8 +5,13 @@
 #include <asm/mmu.h>
 
 extern phys_addr_t get_immrbase(void);
+#if defined(CONFIG_CPM2) || defined(CONFIG_QUICC_ENGINE) || defined(CONFIG_8xx)
 extern u32 get_brgfreq(void);
 extern u32 get_baudrate(void);
+#else
+static inline u32 get_brgfreq(void) { return -1; }
+static inline u32 get_baudrate(void) { return -1; }
+#endif
 extern u32 fsl_get_sys_freq(void);
 
 struct spi_board_info;

arch/powerpc/sysdev/qe_lib/Kconfig

@@ -22,5 +22,6 @@ config UCC
 
 config QE_USB
 	bool
+	default y if USB_GADGET_FSL_QE
 	help
-	  QE USB Host Controller support
+	  QE USB Controller support

arch/powerpc/sysdev/qe_lib/gpio.c

@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
+#include <linux/err.h>
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
@@ -24,8 +25,14 @@ struct qe_gpio_chip {
 	struct of_mm_gpio_chip mm_gc;
 	spinlock_t lock;
 
+	unsigned long pin_flags[QE_PIO_PINS];
+#define QE_PIN_REQUESTED 0
+
 	/* shadowed data register to clear/set bits safely */
 	u32 cpdata;
+
+	/* saved_regs used to restore dedicated functions */
+	struct qe_pio_regs saved_regs;
 };
 
 static inline struct qe_gpio_chip *
@@ -40,6 +47,12 @@ static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 
 	qe_gc->cpdata = in_be32(&regs->cpdata);
+	qe_gc->saved_regs.cpdata = qe_gc->cpdata;
+	qe_gc->saved_regs.cpdir1 = in_be32(&regs->cpdir1);
+	qe_gc->saved_regs.cpdir2 = in_be32(&regs->cpdir2);
+	qe_gc->saved_regs.cppar1 = in_be32(&regs->cppar1);
+	qe_gc->saved_regs.cppar2 = in_be32(&regs->cppar2);
+	qe_gc->saved_regs.cpodr = in_be32(&regs->cpodr);
 }
 
 static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
@@ -103,6 +116,188 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 	return 0;
 }
 
+struct qe_pin {
+	/*
+	 * The qe_gpio_chip name is unfortunate, we should change that to
+	 * something like qe_pio_controller. Someday.
+	 */
+	struct qe_gpio_chip *controller;
+	int num;
+};
+
+/**
+ * qe_pin_request - Request a QE pin
+ * @np:		device node to get a pin from
+ * @index:	index of a pin in the device tree
+ * Context:	non-atomic
+ *
+ * This function return qe_pin so that you could use it with the rest of
+ * the QE Pin Multiplexing API.
+ */
+struct qe_pin *qe_pin_request(struct device_node *np, int index)
+{
+	struct qe_pin *qe_pin;
+	struct device_node *gc;
+	struct of_gpio_chip *of_gc = NULL;
+	struct of_mm_gpio_chip *mm_gc;
+	struct qe_gpio_chip *qe_gc;
+	int err;
+	int size;
+	const void *gpio_spec;
+	const u32 *gpio_cells;
+	unsigned long flags;
+
+	qe_pin = kzalloc(sizeof(*qe_pin), GFP_KERNEL);
+	if (!qe_pin) {
+		pr_debug("%s: can't allocate memory\n", __func__);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	err = of_parse_phandles_with_args(np, "gpios", "#gpio-cells", index,
+					  &gc, &gpio_spec);
+	if (err) {
+		pr_debug("%s: can't parse gpios property\n", __func__);
+		goto err0;
+	}
+
+	if (!of_device_is_compatible(gc, "fsl,mpc8323-qe-pario-bank")) {
+		pr_debug("%s: tried to get a non-qe pin\n", __func__);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	of_gc = gc->data;
+	if (!of_gc) {
+		pr_debug("%s: gpio controller %s isn't registered\n",
+			 np->full_name, gc->full_name);
+		err = -ENODEV;
+		goto err1;
+	}
+
+	gpio_cells = of_get_property(gc, "#gpio-cells", &size);
+	if (!gpio_cells || size != sizeof(*gpio_cells) ||
+			*gpio_cells != of_gc->gpio_cells) {
+		pr_debug("%s: wrong #gpio-cells for %s\n",
+			 np->full_name, gc->full_name);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	err = of_gc->xlate(of_gc, np, gpio_spec, NULL);
+	if (err < 0)
+		goto err1;
+
+	mm_gc = to_of_mm_gpio_chip(&of_gc->gc);
+	qe_gc = to_qe_gpio_chip(mm_gc);
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (test_and_set_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[err]) == 0) {
+		qe_pin->controller = qe_gc;
+		qe_pin->num = err;
+		err = 0;
+	} else {
+		err = -EBUSY;
+	}
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	if (!err)
+		return qe_pin;
+err1:
+	of_node_put(gc);
+err0:
+	kfree(qe_pin);
+	pr_debug("%s failed with status %d\n", __func__, err);
+	return ERR_PTR(err);
+}
+EXPORT_SYMBOL(qe_pin_request);
+
+/**
+ * qe_pin_free - Free a pin
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function frees the qe_pin structure and makes a pin available
+ * for further qe_pin_request() calls.
+ */
+void qe_pin_free(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	unsigned long flags;
+	const int pin = qe_pin->num;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+	test_and_clear_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[pin]);
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	kfree(qe_pin);
+}
+EXPORT_SYMBOL(qe_pin_free);
+
+/**
+ * qe_pin_set_dedicated - Revert a pin to a dedicated peripheral function mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function resets a pin to a dedicated peripheral function that
+ * has been set up by the firmware.
+ */
+void qe_pin_set_dedicated(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	struct qe_pio_regs *sregs = &qe_gc->saved_regs;
+	int pin = qe_pin->num;
+	u32 mask1 = 1 << (QE_PIO_PINS - (pin + 1));
+	u32 mask2 = 0x3 << (QE_PIO_PINS - (pin % (QE_PIO_PINS / 2) + 1) * 2);
+	bool second_reg = pin > (QE_PIO_PINS / 2) - 1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (second_reg) {
+		clrsetbits_be32(&regs->cpdir2, mask2, sregs->cpdir2 & mask2);
+		clrsetbits_be32(&regs->cppar2, mask2, sregs->cppar2 & mask2);
+	} else {
+		clrsetbits_be32(&regs->cpdir1, mask2, sregs->cpdir1 & mask2);
+		clrsetbits_be32(&regs->cppar1, mask2, sregs->cppar1 & mask2);
+	}
+
+	if (sregs->cpdata & mask1)
+		qe_gc->cpdata |= mask1;
+	else
+		qe_gc->cpdata &= ~mask1;
+
+	out_be32(&regs->cpdata, qe_gc->cpdata);
+	clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_dedicated);
+
+/**
+ * qe_pin_set_gpio - Set a pin to the GPIO mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function sets a pin to the GPIO mode.
+ */
+void qe_pin_set_gpio(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	/* Let's make it input by default, GPIO API is able to change that. */
+	__par_io_config_pin(regs, qe_pin->num, QE_PIO_DIR_IN, 0, 0, 0);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_gpio);
+
 static int __init qe_add_gpiochips(void)
 {
 	struct device_node *np;

arch/powerpc/sysdev/simple_gpio.c

+/*
+ * Simple Memory-Mapped GPIOs
+ *
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <asm/prom.h>
+#include "simple_gpio.h"
+
+struct u8_gpio_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u8 data;
+};
+
+static struct u8_gpio_chip *to_u8_gpio_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct u8_gpio_chip, mm_gc);
+}
+
+static u8 u8_pin2mask(unsigned int pin)
+{
+	return 1 << (8 - 1 - pin);
+}
+
+static int u8_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+	return in_8(mm_gc->regs) & u8_pin2mask(gpio);
+}
+
+static void u8_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+	unsigned long flags;
+
+	spin_lock_irqsave(&u8_gc->lock, flags);
+
+	if (val)
+		u8_gc->data |= u8_pin2mask(gpio);
+	else
+		u8_gc->data &= ~u8_pin2mask(gpio);
+
+	out_8(mm_gc->regs, u8_gc->data);
+
+	spin_unlock_irqrestore(&u8_gc->lock, flags);
+}
+
+static int u8_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	return 0;
+}
+
+static int u8_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	u8_gpio_set(gc, gpio, val);
+	return 0;
+}
+
+static void u8_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+
+	u8_gc->data = in_8(mm_gc->regs);
+}
+
+static int __init u8_simple_gpiochip_add(struct device_node *np)
+{
+	int ret;
+	struct u8_gpio_chip *u8_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	u8_gc = kzalloc(sizeof(*u8_gc), GFP_KERNEL);
+	if (!u8_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&u8_gc->lock);
+
+	mm_gc = &u8_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = u8_gpio_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 8;
+	gc->direction_input = u8_gpio_dir_in;
+	gc->direction_output = u8_gpio_dir_out;
+	gc->get = u8_gpio_get;
+	gc->set = u8_gpio_set;
+
+	ret = of_mm_gpiochip_add(np, mm_gc);
+	if (ret)
+		goto err;
+	return 0;
+err:
+	kfree(u8_gc);
+	return ret;
+}
+
+void __init simple_gpiochip_init(const char *compatible)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, compatible) {
+		int ret;
+		struct resource r;
+
+		ret = of_address_to_resource(np, 0, &r);
+		if (ret)
+			goto err;
+
+		switch (resource_size(&r)) {
+		case 1:
+			ret = u8_simple_gpiochip_add(np);
+			if (ret)
+				goto err;
+			break;
+		default:
+			/*
+			 * Whenever you need support for GPIO bank width > 1,
+			 * please just turn u8_ code into huge macros, and
+			 * construct needed uX_ code with it.
+			 */
+			ret = -ENOSYS;
+			goto err;
+		}
+		continue;
+err:
+		pr_err("%s: registration failed, status %d\n",
+		       np->full_name, ret);
+	}
+}

arch/powerpc/sysdev/simple_gpio.h

+#ifndef __SYSDEV_SIMPLE_GPIO_H
+#define __SYSDEV_SIMPLE_GPIO_H
+
+#include <linux/errno.h>
+
+#ifdef CONFIG_SIMPLE_GPIO
+extern void simple_gpiochip_init(const char *compatible);
+#else
+static inline void simple_gpiochip_init(const char *compatible) {}
+#endif /* CONFIG_SIMPLE_GPIO */
+
+#endif /* __SYSDEV_SIMPLE_GPIO_H */

drivers/char/Kconfig

@@ -616,6 +616,7 @@ config HVC_ISERIES
 	default y
 	select HVC_DRIVER
 	select HVC_IRQ
+	select VIOPATH
 	help
 	  iSeries machines support a hypervisor virtual console.
 

drivers/char/hvc_beat.c

@@ -44,7 +44,7 @@ static int hvc_beat_get_chars(uint32_t vtermno, char *buf, int cnt)
 	static unsigned char q[sizeof(unsigned long) * 2]
 		__attribute__((aligned(sizeof(unsigned long))));
 	static int qlen = 0;
-	unsigned long got;
+	u64 got;
 
 again:
 	if (qlen) {
@@ -63,7 +63,7 @@ again:
 		}
 	}
 	if (beat_get_term_char(vtermno, &got,
-		((unsigned long *)q), ((unsigned long *)q) + 1) == 0) {
+		((u64 *)q), ((u64 *)q) + 1) == 0) {
 		qlen = got;
 		goto again;
 	}

drivers/mtd/devices/Kconfig

@@ -120,6 +120,13 @@ config MTD_PHRAM
 	  doesn't have access to, memory beyond the mem=xxx limit, nvram,
 	  memory on the video card, etc...
 
+config MTD_PS3VRAM
+	tristate "PS3 video RAM"
+	depends on FB_PS3
+	help
+	  This driver allows you to use excess PS3 video RAM as volatile
+	  storage or system swap.
+
 config MTD_LART
 	tristate "28F160xx flash driver for LART"
 	depends on SA1100_LART

drivers/mtd/devices/Makefile

@@ -16,3 +16,4 @@ obj-$(CONFIG_MTD_LART)		+= lart.o
 obj-$(CONFIG_MTD_BLOCK2MTD)	+= block2mtd.o
 obj-$(CONFIG_MTD_DATAFLASH)	+= mtd_dataflash.o
 obj-$(CONFIG_MTD_M25P80)	+= m25p80.o
+obj-$(CONFIG_MTD_PS3VRAM)	+= ps3vram.o

drivers/scsi/Kconfig

@@ -884,6 +884,7 @@ config SCSI_IBMVSCSI
 	tristate "IBM Virtual SCSI support"
 	depends on PPC_PSERIES || PPC_ISERIES
 	select SCSI_SRP_ATTRS
+	select VIOPATH if PPC_ISERIES
 	help
 	  This is the IBM POWER Virtual SCSI Client
 

drivers/serial/Kconfig

@@ -1320,13 +1320,30 @@ config SERIAL_NETX_CONSOLE
 config SERIAL_OF_PLATFORM
 	tristate "Serial port on Open Firmware platform bus"
 	depends on PPC_OF
-	depends on SERIAL_8250
+	depends on SERIAL_8250 || SERIAL_OF_PLATFORM_NWPSERIAL
 	help
 	  If you have a PowerPC based system that has serial ports
 	  on a platform specific bus, you should enable this option.
 	  Currently, only 8250 compatible ports are supported, but
 	  others can easily be added.
 
+config SERIAL_OF_PLATFORM_NWPSERIAL
+	tristate "NWP serial port driver"
+	depends on PPC_OF && PPC_DCR
+	select SERIAL_OF_PLATFORM
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_CORE
+	help
+	  This driver supports the cell network processor nwp serial
+	  device.
+
+config SERIAL_OF_PLATFORM_NWPSERIAL_CONSOLE
+	bool "Console on NWP serial port"
+	depends on SERIAL_OF_PLATFORM_NWPSERIAL=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Support for Console on the NWP serial ports.
+
 config SERIAL_QE
 	tristate "Freescale QUICC Engine serial port support"
 	depends on QUICC_ENGINE

drivers/serial/Makefile

@@ -72,6 +72,7 @@ obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
 obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
 obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
+obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o

drivers/serial/of_serial.c

@@ -14,6 +14,7 @@
 #include <linux/serial_core.h>
 #include <linux/serial_8250.h>
 #include <linux/of_platform.h>
+#include <linux/nwpserial.h>
 
 #include <asm/prom.h>
 
@@ -99,9 +100,16 @@ static int __devinit of_platform_serial_probe(struct of_device *ofdev,
 		goto out;
 
 	switch (port_type) {
+#ifdef CONFIG_SERIAL_8250
 	case PORT_8250 ... PORT_MAX_8250:
 		ret = serial8250_register_port(&port);
 		break;
+#endif
+#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
+	case PORT_NWPSERIAL:
+		ret = nwpserial_register_port(&port);
+		break;
+#endif
 	default:
 		/* need to add code for these */
 	case PORT_UNKNOWN:
@@ -129,9 +137,16 @@ static int of_platform_serial_remove(struct of_device *ofdev)
 {
 	struct of_serial_info *info = ofdev->dev.driver_data;
 	switch (info->type) {
+#ifdef CONFIG_SERIAL_8250
 	case PORT_8250 ... PORT_MAX_8250:
 		serial8250_unregister_port(info->line);
 		break;
+#endif
+#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
+	case PORT_NWPSERIAL:
+		nwpserial_unregister_port(info->line);
+		break;
+#endif
 	default:
 		/* need to add code for these */
 		break;
@@ -148,6 +163,10 @@ static struct of_device_id __devinitdata of_platform_serial_table[] = {
 	{ .type = "serial", .compatible = "ns16450",  .data = (void *)PORT_16450, },
 	{ .type = "serial", .compatible = "ns16550",  .data = (void *)PORT_16550, },
 	{ .type = "serial", .compatible = "ns16750",  .data = (void *)PORT_16750, },
+#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
+	{ .type = "serial", .compatible = "ibm,qpace-nwp-serial",
+					.data = (void *)PORT_NWPSERIAL, },
+#endif
 	{ .type = "serial",			      .data = (void *)PORT_UNKNOWN, },
 	{ /* end of list */ },
 };

include/linux/nwpserial.h

+/*
+ *  Serial Port driver for a NWP uart device
+ *
+ *    Copyright (C) 2008 IBM Corp., Benjamin Krill <ben@codiert.org>
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  as published by the Free Software Foundation; either version
+ *  2 of the License, or (at your option) any later version.
+ *
+ */
+#ifndef _NWPSERIAL_H
+#define _NWPSERIAL_H
+
+int nwpserial_register_port(struct uart_port *port);
+void nwpserial_unregister_port(int line);
+
+#endif /* _NWPSERIAL_H */

include/linux/serial_core.h

@@ -161,6 +161,9 @@
 
 #define PORT_S3C6400	84
 
+/* NWPSERIAL */
+#define PORT_NWPSERIAL	85
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>