The mesh_path_add() read-locks the pathtbl_resize_lock and calls
kmalloc with GFP_KERNEL mask.

Fix it and move the endadd2 label lower. It should be _before_ the
if() beyond, but it makes no sense for it being there, so I move it
right after this if().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Without this patch, if xmit_skb is null but net_ratelimit() returns 0 we would
go to the else branch and access the null xmit_skb. Pointed out by Johannes
Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should have been updated at the same time we were transitioning from 3 byte
to 4 byte mesh sequence number. Pointed out by Johannes Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 should set the IEEE80211_TX_CTL_DO_NOT_ENCRYPT flag in tx_control
structure to inform drivers not to encrypt the beacon. Drivers that only check
for that flag before accessing the hw_key field, will otherwise cause a NULL
pointer dereference since that field is not configured for beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When, for some reason, the rt2x00pci module fails to allocate DMA memory for
the queues, it tries to undo the complete initialization of the PCI device,
including freeing of the irq. This results in the following error in dmesg, as
the irq hadn't been requested yet:

[  78.123456] Trying to free already-free IRQ 17

Fix this by implementing proper error handling code, instead of just using the
full uninitialization function.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During initialization the initialize() callback function
in rt2x00pci and rt2x00usb will cleanup the mess they made.

rt2x00lib shouldn't call uninitialize because the callback function already
cleaned up _and_ the DEVICE_INITIALIZED isn't set which causes the
rt2x00lib_uninitialize() to halt directly anyway. All that is required
to be cleaned up by rt2x00lib is the queue, and that can be done by
calling rt2x00queue_uninitialize() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00pci allocates DMA for descriptor and data,
rt61pci doesn't use this for the beacon, but it can
use the descriptor part as temporary buffer instead
of using pskb_expand_head().
Using this temporary buffer is obviously much better
then reallocating the skb buffer...

At the same time we can set the data length for the
beacon queue at 0, to make sure no DMA is allocated for
data (but just for the descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make iwl4965_lq_sta->drv available even without CONFIG_MAC80211_DEBUGFS.
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under certain circumstances (in AP mode) the debugfs function
that is supposed to add the default key symlink can encounter
a NULL default_key pointer. This patch makes it handle that
situtation gracefully.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported by Daniel Marjamäki <danielm77@spray.se> here:

	http://bugzilla.kernel.org/show_bug.cgi?id=10588Signed-off-by: John W. Linville <linville@tuxdriver.com>

A file in the net/mac80211 directory uses "int" for flags.  This can cause
hard to find bugs on some architectures.  This patch converts the flags to use
"long" instead.

This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a regression introduced by commit 7b463ced (prism54: set
carrier flags correctly) which causes the device to come up without
a carrier in AP-mode.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If socket is create by AF_INET type, add IPv6 address to asoc will cause
kernel panic while packet is transmitted on that transport.

This patch add address type check before process paramaters of ASCONF
chunk. If peer is not support this address type, return with error
invald parameter.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If socket is create by PF_INET type, it can not used IPv6 address to
send/recv DATA, So we can not used IPv6 address even if peer tell us it
support IPv6 address.
This patch fix to only enabled peer IPv6 address support on PF_INET6 socket.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Determine the number of physical ports from the card's VPD data.
Previous fix failed on Maramba platform which doesn't have the
"board-model" property. This fix uses the "model" property which
exists on all cards and Neptune based motherboards.

cstyle cleanup included.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Noticed by Paul Marks <paul@pmarks.net>.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch increases the headroom TIPC reserves in each sk_buff
to accommodate the largest possible link level device header.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_open() and dev_close() must be called holding the RTNL, since they
call device functions and netdevice notifiers that are promised the RTNL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx packet counting and the local loopback of CAN frames should
only happen in the case that the CAN frame has been enqueued to the
netdevice tx queue successfully.

Thanks to Andre Naujoks <nautsch@gmail.com> for reporting this issue.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a net namespace is destroyed, some devices (those, not killed
on ns stop explicitly) are moved back to init_net.

The problem, is that this net_ns change has one point of failure -
the __dev_alloc_name() may be called if a name collision occurs (and
this is easy to trigger). This allocator performs a likely-to-fail
GFP_ATOMIC allocation to find a suitable number. Other possible 
conditions that may cause error (for device being ns local or not
registered) are always false in this case.

So, when this call fails, the device is unregistered. But this is
*not* the right thing to do, since after this the device may be
released (and kfree-ed) improperly. E. g. bridges require more
actions (sysfs update, timer disarming, etc.), some other devices 
want to remove their private areas from lists, etc.

I. e. arbitrary use-after-free cases may occur.

The proposed fix is the following: since the only reason for the
dev_change_net_namespace to fail is the name generation, we may
give it a unique fall-back name w/o %d-s in it - the dev<ifindex>
one, since ifindexes are still unique.

So make this change, raise the failure-case printk loglevel to 
EMERG and replace the unregister_netdevice call with BUG().

[ Use snprintf() -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When conntrack and DCCP/SCTP protocols are enabled, chances are good
that people also want DCCP/SCTP conntrack and NAT support.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Inovaphone PBXs exhibit very stange behaviour: when dialing for
example "123", the device sends INVITE requests for "1", "12" and
"123" back to back.  The first requests will elicit error responses
from the receiver, causing the SIP helper to flush the RTP
expectations even though we might still see a positive response.

Note the sequence number of the last INVITE request that contained a
media description and only flush the expectations when receiving a
negative response for that sequence number.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As noticed by Ben Greear, macvlan crashes the kernel when unloading the
module. The reason is that it tries to clean up the macvlan_port pointer
on the macvlan device itself instead of the underlying device. A non-NULL
pointer is taken as indication that the macvlan_handle_frame_hook is
valid, when receiving the next packet on the underlying device it tries
to call the NULL hook and crashes.

Clean up the macvlan_port on the correct device to fix this.

Signed-off-by; Patrick McHardy <kaber@trash.net>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 1122 does not have a section 3.1.2.2. The requirement to silently
discard datagrams with a bad checksum is in section 3.2.1.2 instead.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10611Signed-off-by: J.H.M. Dassen (Ray) <jdassen@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Note: there's actually another bug in FRTO's SACK variant, which
is the causing failure in NewReno case because of the error
that's fixed here. I'll fix the SACK case separately (it's
a separate bug really, though related, but in order to fix that
I need to audit tp->snd_nxt usage a bit).

There were two places where SACK variant of FRTO is getting
incorrectly used even if SACK wasn't negotiated by the TCP flow.
This leads to incorrect setting of frto_highmark with NewReno
if a previous recovery was interrupted by another RTO.

An eventual fallback to conventional recovery then incorrectly
considers one or couple of segments as forward transmissions
though they weren't, which then are not LOST marked during
fallback making them "non-retransmittable" until the next RTO.
In a bad case, those segments are really lost and are the only
one left in the window. Thus TCP needs another RTO to continue.
The next FRTO, however, could again repeat the same events
making the progress of the TCP flow extremely slow.

In order for these events to occur at all, FRTO must occur
again in FRTOs step 3 while the key segments must be lost as
well, which is not too likely in practice. It seems to most
frequently with some small devices such as network printers
that *seem* to accept TCP segments only in-order. In cases
were key segments weren't lost, things get automatically
resolved because those wrongly marked segments don't need to be
retransmitted in order to continue.

I found a reproducer after digging up relevant reports (few
reports in total, none at netdev or lkml I know of), some
cases seemed to indicate middlebox issues which seems now
to be a false assumption some people had made. Bugzilla
#10063 _might_ be related. Damon L. Chesser <damon@damtek.com>
had a reproducable case and was kind enough to tcpdump it
for me. With the tcpdump log it was quite trivial to figure
out.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

On a read error, e1000e might have returned uninitialized block of
eeprom data back to userspace. The convention is that 0xff is "empty",
so mark the entire eeprom as empty in case of an error.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit 9fb1e350,
ucc_geth: use rx-clock-name and tx-clock-name device tree properties
Introduced a typo that made the driver use the RX clock
as TX clock, causing massive TX errors.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Otherwise theoretically at least

	CAP_NET_ADMIN
	Reload new firmware
	Wait..
	Firmware patches kernel

So it should be CAY_SYS_RAWIO - not that I suspect this is in fact a
credible attack vector!
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Delete the non-napi code from the driver and Kconfig.
Tested x86_64.  Apply at next open opportunity.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

There are more memory leaks in the !PPC_CPM_NEW_BINDING case, but that code
will disappear soon along with arch/ppc.

Reported by Daniel Marjamki <danielm77@spray.se> at
http://bugzilla.kernel.org/show_bug.cgi?id=10591Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Taken from http://bugzilla.kernel.org/show_bug.cgi?id=10577

I was unable to access a computer containing an Intel EtherExpress 16 network
card using IPv6.

I traced this to failure of neighbour discovery.  When I used an "ip -6 neigh
add" command, on the computer attempting access, to insert a binding between
the IPv6 address of the computer with the Intel EtherExpress 16 network card
and the card's ethernet address, I was able to access that computer using
IPv6.

Neighbour discovery requires working multicast.  The driver sources file
eexpress.c contains an approximately 30 line function eexp_setup_filter used
when loading multicast addresses.

I found 3 problems in this function

1) It wrote the number of multicast addresses to the card instead of the
    number of bytes in the multicast addresses.

2) When loading multiple multicast addresses it loaded the first one
    provided multiple times instead of loading each one once.

3) The setting of pointer 'data' from 'dmi->dmi_addr' occured before the
    test for the error situation of 'dmi' being NULL.

Correcting these problems allows the computer with the Intel EtherExpress 16
network card to found by IPv6 neighbour discovery.

p.s. There is some information on the Intel EtherExpress 16 at
http://www.intel.com/support/etherexpress/vintage/sb/cs-013500.htm
Datasheet for the Intel 82586 ethernet controller used by the card
http://www.datasheetcatalog.com/datasheets_pdf/8/2/5/8/82586.shtmlSigned-off-by: Bruce Robson <bns_robson@hotmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The ethernet card 3c980-TX needs a mdio_sync() to initialize the ethernet
properly. This is forced by adding an EXTRA_PREAMBLE to its drv_flags.

Without this, the driver did not reconnect after a link loss.
Signed-off-by: Gunnar Larisch <Gunnar.Larisch@gmx.de>
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/net/appletalk/cops.c: In function ‘cops_reset’:
drivers/net/appletalk/cops.c:507: warning: comparison of distinct pointer
types lacks a cast

by replacing hand-woven msleep() with call to msleep()
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.

This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).

To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch fixes uli526x driver's issues on a PowerPC boards: uli chip
is unable to receive the packets.

It appears that send_frame_filter prepares the setup frame in the
endianness unsafe manner. On a big endian machines we should shift
the address nibble by two bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The firmware on MPC8610HPCD boards enables ULI ethernet and leaves it
in some funky state before booting Linux. For drivers, it's always good
idea to (re)initialize the hardware prior to requesting interrupts.

This patch fixes the following oops:

Oops: Kernel access of bad area, sig: 11 [#1]
MPC86xx HPCD
NIP: c0172820 LR: c017287c CTR: 00000000
[...]
NIP [c0172820] allocate_rx_buffer+0x2c/0xb0
LR [c017287c] allocate_rx_buffer+0x88/0xb0
Call Trace:
[df82bdc0] [c017287c] allocate_rx_buffer+0x88/0xb0 (unreliable)
[df82bde0] [c0173000] uli526x_interrupt+0xe4/0x49c
[df82be20] [c0045418] request_irq+0xf0/0x114
[df82be50] [c01737b0] uli526x_open+0x48/0x160
[df82be70] [c0201184] dev_open+0xb0/0xe8
[df82be80] [c0200104] dev_change_flags+0x90/0x1bc
[df82bea0] [c035fab0] ip_auto_config+0x214/0xef4
[df82bf60] [c03421c8] kernel_init+0xc4/0x2ac
[df82bff0] [c0010834] kernel_thread+0x44/0x60
Instruction dump:
4e800020 9421ffe0 7c0802a6 bfa10014 7c7e1b78 90010024 80030060 83e30054
2b80002f 419d0078 3fa0c039 48000058 <907f0010> 80630088 2f830000 419e0014
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>