This weekend I was hacking around with a trivial USB driver for talking
to the boot load firmware of a USB Bit Whacker.  It's running the
MicroChip Pic18 boot loader firmware and I'm putting together a flash
program for writing new FW to the thing.

Anyway in my use of the usb-skeleton.c as my starting point I discovered
my test program was getting hung up after attempting to write a buffer.
The application and driver where hung in a way that required me to
reboot to get it to clean up so I could try again.

It turned out the code path through skel_open can grap the driver's
io_mutex lock and forget to release it.

The following patch fixes the problem for me.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended.  This will be true even when
CONFIG_USB_SUSPEND is not enabled.

In addition, an extra can_submit flag is added to the usb_device
structure.  That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.

It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag.  This also permits us to remove
some questionable references to the deprecated power.power_state field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines.  The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete.  The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method.  The changeover is easy because the routine currently has only
one caller.

This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.

As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods.  It is now guaranteed that there will
be none.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as987) changes the way FREEZE and PRETHAW suspend events
are handled in usbcore.  The decision about whether or not to ignore
them for non-root devices is pushed down into the USB-device driver,
instead of being made in the core code.

This is appropriate, since devices exported to a virtualized guest or
over a network may indeed need to handle these types of suspend, even
though normal devices don't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as990) removes an annoying debugging message.  Nobody
really cares when endpoint pseudo-devices are released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Thomas Dahlmann <thomas.dahlmann@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/misc/sisusbvga/sisusb.c: In function sisusb_open
drivers/usb/misc/sisusbvga/sisusb.c:2444: warning: sisusb is used uninitialized in this function

is a genuine bug (which will cause oops). We cannot use "sisusb" in
error path for (!interface), because sisusb will itself be derived
from "interface" later.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

the iuu_phoenix driver submits another URB from a completion handler.
This dictates a certain order of calls to usb_kill_urb() in kill_traffic().
As other drivers may do it the other way round, we need to use both
orders in kill_traffic().
This patch does so and should be merged before iuu_phoenix is merged.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The ELAN U132 Host Controller Driver uses the semaphore sw_lock as
mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is a reworked version of this patch:
http://www.mail-archive.com/linux-usb-devel%40lists.sourceforge.net/msg55094/activate_huawei_dev.patch

That properly initializes the HUAWEI E220 devices into multi-port mode.
Signed-off-by: Johann Wilhelm <johann.wilhelm@student.tugraz.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as984) fixes a rather elementary mistake in dummy_hcd.
The new statement label should come before the spin_unlock_irqrestore,
not after it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as981) removes the remaining nontrivial usages of
urb->status from usbcore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Now that urb->status isn't used, urb->lock doesn't protect anything.
This patch (as980) removes it and replaces it with a private mutex in
the one remaining place it was still used: usb_kill_urb.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator.  Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as978) reorganizes the way usbmon uses urb->status.  It
now accepts the status value as an argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as977) reorganizes the way r8a66597-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

Parts of this patch were written by Yoshihiro Shimoda.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as976) reorganizes the way sl811-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

The patch also improves the handling of faults during the status stage
of a control transfer, since it no longer needs to retain the error
information from the earlier stages.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as975) reorganizes the way ohci-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as974) reorganizes the way ehci-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

The patch also simplifies the handling of -EREMOTEIO, since the only
use of that code is to set the do_status flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as973) reorganizes the way dummy-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the BenQ Mobile Phone EF81 to pl2303
Signed-off-by: Andreas Loibl <andreas@andreas-loibl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In drivers/usb/serial/oti6858.c::pl2303_buf_alloc() the return value
of kmalloc() is being cast to "struct pl2303_buf *", but that need
not be done here since kmalloc() returns "void *".
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Update usbmon documentation, mentioning the "zero" (wildcard) bus.
Possibly, in my first hunk, the 'either ... or ...' should be rephrased a bit to
be expressed better.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some usb-serial devices (e.g. certain Edgeport models) have more than
one serial port on the same USB device/interface.

Currently the only way to distinguish these ports in userspace is by
their minor device number: the driver makes them consecutive and in
stable order.

However, for the purpose of stable naming with udev this is
insufficient: when udev handles the ADD event for one of the ports it
doesn't know what minor number the other one has.

To make stable naming easier, export the port number via sysfs.
Signed-off-by: Roman Kagan <rkagan@sw.ru>
Signed-off-by: Dmitry Guryanov <dimak@dgap.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This fixes a small memory leak that happens every time the device is
plugged in.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as983) makes a test for minimum-length command sizes in
g_file_storage less restrictive.  It doesn't matter because commands
with bad lengths will be detected later on anyway, and doing it like
this makes the driver interoperable with certain buggy hosts such as
the JVC HiFi (reported by Samuel Hangouet).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

No hardware but this driver is currently totally broken so we can't make
it much worse. Remove all tbe broken invalid termios handling and replace
it with a proper set_termios method.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as972) changes ohci-hcd so that after an error occurs, the
remaining TDs for the URB will be skipped over entirely instead of
going through the donelist.  This enables the driver to give back the
URB as soon as the error is detected, avoiding the need to store the
error status in urb->status.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as971) fixes a small mistake: The URB's completion status
needs to be adjusted before the URB is passed to usmon_urb_complete(),
not afterward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Handle the FT232RL device type in exactly the same way as FT232BM
devices (FT232RL detection was added around kernel 2.6.20 but not code
for handling it).
Signed-off-by: Andrew M. Bishop <amb@gedanken.demon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more.  To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses.  The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.

By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (968) changes the way uhci-hcd reports status for
Isochronous URBs.  Until now urb->status has been set to the last
detected error code.  But other HCDs don't do this; they leave the
status set to 0 and report errors only in the individual iso packet
descriptors.  So this patch removes the extra computation and makes
uhci-hcd behave like the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as967) makes a few relatively minor changes to the
r8a66597 driver:

	finish_request() does nothing but call done(), so merge the
	two routines.

	Detect and report -EOVERFLOW errors.

	Fix the calculation that checks for short packets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It is not necessary to powerdown the ports on ehci_pci_reinit() when the
chip reset already did that.  Removing this saves 20ms during restart
after poweroff paths (which OLPC uses a lot).

To ensure driver startup then behaves consistently, force a reset during
driver startup.  (Not doing this was an accident of some previous changes
to the init sequence.)

Make the corresponding change in the PS3 support.  It's not clear what
ehci-fsl should do here; it has similar code to the PS3.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <rvinson@mvista.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Update copyrights and remove not necessary warning (ueagle-atm works
well on suspend/resume).
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Do not sleep in kernel thread when device is disconnected, this make faster
suspending and module unloading. Use one wait queue for sleeping.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Ueagle-atm driver load DSP firmware in function, which is running from
common workqueue. In some (error) circumstances loading firmware may
sleep for long periods (even 60 seconds, depending on timeout). This
block keyboard driver, which also use common workqueue. To fix problem
use custom workqueue in ueagle-atm.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Let's user control how much USB bus bandwidth will be reserved by
ueagle-atm device. This make possible to share bus with other devices
when ueagle-atm driver works in isochronous mode.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>