The sequence executed in check_sal_cache_flush:

	- pend a timer interrupt
	- call SAL_CACHE_FLUSH
	- see if interrupt is still pending

can hang HP machines with buggy SAL_CACHE_FLUSH implementations.

Provide a kernel command-line argument to allow users skip this
check if desired. Using this parameter will force ia64_sal_cache_flush
to call ia64_pal_cache_flush() instead of SAL_CACHE_FLUSH.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Some IA64 machines map all cell-local memory above 4 GB (32 bit limit).
However, in most cases, the kernel needs some memory below that limit that is
DMA-capable. So in this machine configuration, the crashkernel will be reserved
above 4 GB.

For machines that use SWIOTLB implementation because they lack an I/O MMU
the low memory is required by the SWIOTLB implementation. In that case,
it doesn't make sense to reserve the crashkernel at all because it's unusable
for kdump.

A special case is the "hpzx1" machine vector. In theory, it has a I/O MMU, so
it can be booted above 4 GB. However, in the kdump case that is not possible
because of changeset 51b58e3e:

    On HP zx1 machines, the 'machvec=dig' parameter is needed for the kdump
    kernel to avoid problems with the HP sba iommu.  The problem is that during
    the boot of the kdump kernel, the iommu is re-initialized, so in-flight DMA
    from improperly shutdown drivers causes an IOTLB miss which leads to an
    MCA.  With kdump, the idea is to get into the kdump kernel with as little
    code as we can, so shutting down drivers properly is not an option.

    The workaround is to add 'machvec=dig' to the kdump kernel boot parameters.
    This makes the kdump kernel avoid using the sba iommu altogether, leaving
    the IOTLB intact.  Any ongoing DMA falls harmlessly outside the kdump
    kernel.  After the kdump kernel reboots, all devices will have been
    shutdown properly and DMA stopped.

This patch pushes that functionality into the sba iommu initialization
code, so that users won't have to find the obscure documentation telling
them about 'machvec=dig'.

This means that also for hpzx1 it's not possible to boot when all
memory is above the 4 GB limit. So the only machine vectors that can handle
this case are "sn2" and "uv".
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This patch adds the basic IA64 machvec infrastructure to support
the SGI "UV" platform.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Add new UV-specific header files.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cxgb3: Wrap the software send queue pointer as needed on flush
  IB/ipath: Change ipath_devdata.ipath_sdma_status to be unsigned long
  IB/ipath: Make ipath_portdata work with struct pid * not pid_t
  IB/ipath: Fix RDMA read response sequence checking
  IB/ipath: Fix many locking issues when switching to error state
  IB/ipath: Fix RC and UC error handling
  RDMA/nes: Fix up nes_lro_max_aggr module parameter

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (70 commits)
  V4L/DVB (7900): pvrusb: Fix Kconfig if DVB=m V4L_core=y
  V4L/DVB (7899): Fixes a few remaining Kbuild issues at common/tuners
  V4L/DVB (7898): Fix VIDEO_MEDIA Kconfig logic
  V4L/DVB (7895): tveeprom: update Hauppauge analog audio and video decoders
  V4L/DVB (7893): xc5000: bug-fix: allow multiple devices in a single system
  V4L/DVB (7891): cx18/ivtv: fix open() kernel oops
  V4L/DVB (7890): cx18: removed bogus and confusing conditional
  V4L/DVB (7889): cx18: improve HVR-1600 detection.
  V4L/DVB (7888): cx18: minor card definition updates.
  V4L/DVB (7887): cx18: fix Compro H900 analog support.
  V4L/DVB (7881): saa7134: fixed a compile warning in saa7134-core.c
  V4L/DVB (7880): saa7134: remove explicit GPIO initialization
  V4L/DVB(7879): Adding cx18 Support for mxl5005s
  V4L/DVB(7878): mxl55005s: Makefile and Kconfig additions
  V4L/DVB(7877): mxl5005s: Ensure debug is off
  V4L/DVB(7876): mxl5005s: Remove incorrect copyright holders
  V4L/DVB(7875): mxl5005s: Remove redundant functions
  V4L/DVB(7874): mxl5005s: Fix function statics
  V4L/DVB(7873): mxl5005s: Fix header includes.
  V4L/DVB(7872): mxl5005s: checkpatch.pl compliance
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  Driver core: struct class remove children list
  block: do_mounts - accept root=<non-existant partition>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
  USB: atmel_usba_udc fixes, mostly disconnect()
  USB: pxa27x_udc: minor fixes
  usbtest: comment on why this code "expects" negative and positive errnos
  USB: remove PICDEM FS USB demo (04d8:000c) device from ldusb
  USB: option: add new Dell 5520 HSDPA variant
  USB: unusual_devs: Add support for GI 0401 SD-Card interface
  USB: serial gadget: descriptor cleanup
  USB: serial gadget: simplify endpoint handling
  USB: serial gadget: remove needless data structure
  USB: serial gadget: cleanup/reorg
  usb: fix compile warning in isp1760
  USB: do not handle device 1410:5010 in 'option' driver
  USB: Fix unusual_devs.h ordering
  USB: add Zoom Telephonics Model 3095F V.92 USB Mini External modem to cdc-acm
  USB: Support for the ET502HS HDSPA modem in option driver
  USB: Support for the ET502HS HDSPA modem
  usb: fix integer as NULL pointer warnings found by sparse
  USB: isp1760: fix printk format
  USB: add Telstra NextG CDMA id to option driver
  USB: add association.h
  ...

because of the class_device was removed, now do the children list removing
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some devices, like md, may create partitions only at first access,
so allow root= to be set to a valid non-existant partition of an
existing disk. This applies only to non-initramfs root mounting.

This fixes a regression from 2.6.24 which did allow this to happen and
broke some users machines :(
Acked-by: Neil Brown <neilb@suse.de>
Tested-by: Joao Luis Meloni Assirati <assirati@nonada.if.usp.br>
Cc: stable <stable@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (73 commits)
  net: Fix typo in net/core/sock.c.
  ppp: Do not free not yet unregistered net device.
  netfilter: xt_iprange: module aliases for xt_iprange
  netfilter: ctnetlink: dump conntrack ID in event messages
  irda: Fix a misalign access issue. (v2)
  sctp: Fix use of uninitialized pointer
  cipso: Relax too much careful cipso hash function.
  tcp FRTO: work-around inorder receivers
  tcp FRTO: Fix fallback to conventional recovery
  New maintainer for Intel ethernet adapters
  DM9000: Use delayed work to update MII PHY state
  DM9000: Update and fix driver debugging messages
  DM9000: Add __devinit and __devexit attributes to probe and remove
  sky2: fix simple define thinko
  [netdrvr] sfc: sfc: Add self-test support
  [netdrvr] sfc: Increment rx_reset when reported as driver event
  [netdrvr] sfc: Remove unused macro EFX_XAUI_RETRAIN_MAX
  [netdrvr] sfc: Fix code formatting
  [netdrvr] sfc: Remove kernel-doc comments for removed members of struct efx_nic
  [netdrvr] sfc: Remove garbage from comment
  ...

There is a possible data race in the page table walking code. After the split
ptlock patches, it actually seems to have been introduced to the core code, but
even before that I think it would have impacted some architectures (powerpc
and sparc64, at least, walk the page tables without taking locks eg. see
find_linux_pte()).

The race is as follows:
The pte page is allocated, zeroed, and its struct page gets its spinlock
initialized. The mm-wide ptl is then taken, and then the pte page is inserted
into the pagetables.

At this point, the spinlock is not guaranteed to have ordered the previous
stores to initialize the pte page with the subsequent store to put it in the
page tables. So another Linux page table walker might be walking down (without
any locks, because we have split-leaf-ptls), and find that new pte we've
inserted. It might try to take the spinlock before the store from the other
CPU initializes it. And subsequently it might read a pte_t out before stores
from the other CPU have cleared the memory.

There are also similar races in higher levels of the page tables. They
obviously don't involve the spinlock, but could see uninitialized memory.

Arch code and hardware pagetable walkers that walk the pagetables without
locks could see similar uninitialized memory problems, regardless of whether
split ptes are enabled or not.

I prefer to put the barriers in core code, because that's where the higher
level logic happens, but the page table accessors are per-arch, and open-coding
them everywhere I don't think is an option. I'll put the read-side barriers
in alpha arch code for now (other architectures perform data-dependent loads
in order).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

read_barrie_depends has always been a noop (not a compiler barrier) on all
architectures except SMP alpha. This brings UP alpha and frv into line with all
other architectures, and fixes incorrect documentation.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Various fixes to Atmel's high speed UDC driver.

  * Issue some missing disconnect() calls.  Currently they are only made
    when VBUS power goes away (on boards where the driver can sense such
    changes), but that's not enough for gadget drivers to clean out all
    the state that's needed.  Missing calls were:

      - After USB reset, before starting enumeration.
      - When unregistering a gadget driver, before unbind().

  * Don't assume gadget drivers provide disconnect callbacks; make sure
    to not call through a null pointer!

  * When the driver doesn't provide an unbind() callback, refuse to
    unregister it.

Also remove two bogus "error" messages:

  * Related to mis-handling of disconnect() ... don't emit error messages
    for disconnect() handlers that disable endpoints.  All of them should
    be doing that; the problem is (unfixed) oddness in atmel_usba_udc.

  * Don't emit a diagnostic for a curious and transient nonfatal error
    that shows up sometimes with EP0.

Those messages spammed syslog, for no good reason.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Minor fixes to pxa27x udc driver :
 - don't clobber driver model bus_id field
 - wrong endianess fix (no functional change; cpu is little-endian)
 - double udc disable fix
 - resume/suspend fix (OTG hold bit)
 - make driver pxa27x dependant (check cpu at runtime)
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

On Mon, May 12, 2008 at 01:02:22AM -0700, David Brownell wrote:
> On Sunday 11 May 2008, Marcin Slusarz wrote:
> > 
> > test_ctrl_queue expects (?) positive and negative errnos.
> > what is going on here?
> 
> The sign is just a way to flag something:
> 
>                 /* some faults are allowed, not required */
> 
> The negative ones are required.  Positive codes are optional,
> in the sense that, depending on how the peripheral happens
> to be implemented, they won't necessarily be triggered.
> 
> For example, the test to fetch a device qualifier desriptor
> must succeed if the device is running at high speed.  So that
> test is marked as negative.  But when it's full speed, it
> could legitimately fail; marked as positive.  And so on for
> other tests.
> 
> Look at how the codes are *interpreted* to see it work.

Lets document it.

Based on comment from David Brownell <david-b@pacbell.net>.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Microchip has changed the PICDEM FS USB demo device (0x04d8:000c)
to use bulk transfer and not interrupt transfer. So I've updated the libusb
based program here (Post #31).
	http://forum.microchip.com/tm.aspx?m=106426&mpage=2

So I believe that the in-kernel ldusb driver will no longer work with the
demo firmware.  It should be removed.
Signed-off-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: Michael Hund <MHund@LD-Didactic.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

New variant of the 5520 found by Luke Sheldrick.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Enables the SD-Card interface on the GI 0401 HSUPA card from Option.

The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.

This revised patch adds a small comment explaining why and reduces the
rev range.

T:  Bus=02 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=0af0 ProdID=7401 Rev= 0.00
S:  Manufacturer=Option N.V.
S:  Product=Globetrotter HSUPA Modem
C:* #Ifs=10 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 0 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 2 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 4 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 5 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 6 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 6 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 7 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 7 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 9 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Bugfix some serial gadget descriptors:

 - Stop mangling the low bits (controller type ID) of bcdDevice;
   just use the high bits for a driver revision code.

 - Serial numbers that aren't specific to individual devices
   are useless; stop reporting "0" for this.

 - Since it's not part of a CDC-conformant function, the "bulk only"
   configuration shouldn't be using "CDC Data" as its interface class.
   Switch over to using CLASS_VENDOR_SPEC (different value, 0xff).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Switch serial gadget away from a *very* old idiom:  just remember
the endpoints we'll be using, instead of looking them up by name
each time.  This is a net code and data (globals) shrink.

Also fix a small memory leak in the rmmod path, by working the
same as the disconnect code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This removes a needless data structure from the serial gadget code;
it's a small code shrink, and a larger data shrink.

Since "struct usb_request" already has a "struct list_head" reserved
for use by gadget drivers, the serial gadget code doesn't need to
allocate wrapper structs to hold that list ... it can (and should!)
just use the list_head provided for that exact use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some cleanup/reorg of g_serial ... simplifying it, and disentangling
its structure so morphing it into a "function" driver (combinable with
other interfaces) should be less painful.

 - Remove most forward declarations
     * put tty and gadget driver structs after their contents
     * snug module init/exit decls next to their functions
     * reordered some functions

 - Other cleanup:
     * convert a funky macro to an inline function
     * snug up module params next to their declarations
     * add missing driver.owner
     * add separator lines between major driver sections

 - Add comments re potential parameter/#define changes:
     * only supports one port (shrank GS_NUM_PORTS)
     * changing from 9600-8-N-1 affects multiple sites

 - Remove net2280-specific optimization ... it was being done
   way too late, can be done by net2280 module options, and in
   any case doesn't matter at any sane serial data rates.

There are no behavioral changes, but the macro thing saves I-space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/isp1760-if.c:275: warning: 'ret' is used uninitialized in this function
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This device is not a serial port, but a virtual CD-ROM device. For
example with my Novatel MC950D:

lsusb -v -d 1410:5010 | grep InterfaceClass
      bInterfaceClass         8 Mass Storage

After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:

% lsusb -v -d 1410:4400 | grep InterfaceClass
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceClass       255 Vendor Specific Class

Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Signed-off-by: Eugeniy Meshcheryakov <eugen@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes ordering problems with entries in unusual_devs.h.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:

May  3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May  3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22

Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: Iain McFarlane <iain@imcfarla.homelinux.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Signed-off-by: Mauro Andreolini <andreoli@weblab.ing.unimo.it>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The attached patch allows to bypass the ZeroCD mechanism for the ET502HS
HDSPA modem, so that it can be mounted as a network device.
Signed-off-by: Mauro Andreolini <andreoli@weblab.ing.unimo.it>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings in isp1760 (in linux-next):

next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As reported by Magnus Boman <captain.magnus@opensuse.org>

Cc: Magnus Boman <captain.magnus@opensuse.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This will be used by the wireless usb code, as well as potentially other
USB code.

Originally based on some .c code written by Inaky Perez-Gonzalez
<inaky.perez-gonzalez@intel.com>

Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.

Unfortunately there are a few attributes which cannot be created that
early.  The "descriptors" attribute is binary and so must be created
separately.  The power-management attributes can't be created until
the dev/power/ group exists.  And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This should work on a KRZR K1m, and some other Motorola phones that do
not use the "standard" cdc ACM protocol to talk to USB hosts.
Tested-by: Jeff Garzik <jeff@garzik.org>
Cc: Jiang Dejun <a5652c@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In sock_queue_rcv_skb()  (net/core/sock.c) it should be:
"Cast sk->rcvbuf ..." instead of: "Cast skb->rcvbuf ..."
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An error path in ppp_create_interface() lacks one and may
BUG in free_netdev() checking for proper dev->reg_state.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using iptables 1.3.8 with kernel 2.6.25, rules which include '-m
iprange' don't automatically pull in xt_iprange module.  Below patch
adds module aliases to fix that.  Patch against latest -git, but seems
like a good candidate for -stable also.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conntrack ID is not put (anymore ?) in event messages. This causes
current ulogd2 code to fail because it uses the ID to build a hash in
userspace. This hash is used to be able to output the starting time of
a connection.

Conntrack ID can be used in userspace application to maintain an easy
match between kernel connections list and userspace one. It may worth
to add it if there is no performance related issue.

[ Patrick: it was never included in events, but really should be ]
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace u16ho with put/get_unaligned functions
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>