The previous code wouldn't work correctly on architectures which have a
non-empty MODULE_SYMBOL_PREFIX, and this version is neater if slightly
less optimal in the built-in case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The patch below adds support for the NAND device on the Amstrad Delta.
This is a 32MiB 8bit Toshiba device, with the data bus connected to the
OMAP MPUIO pins and ALE, CLE, NCE, NRE, NWE and NWP all connected to the
Delta's latch2 16bit latch.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

WARNING: "__moddi3" [drivers/mtd/mtdconcat.ko] undefined!
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

drivers/mtd/devices/docprobe.c: In function `DoC_Probe':
drivers/mtd/devices/docprobe.c:338: warning: assignment from incompatible pointer type
drivers/mtd/devices/docprobe.c:341: warning: assignment from incompatible pointer type

Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Remove forgotten lines from jffs2_scan_eraseblock() which
were unnecessary and may cause problem in some environments.

Thanks to Alexander Belyakov <alexander.belyakov@intel.com>.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Device node major/minor numbers are just stored in the payload of a single
data node. Just extend that to 4 bytes and use new_encode_dev() for it.

We only use the 4-byte format if we _need_ to, if !old_valid_dev(foo).
This preserves backwards compatibility with older code as much as
possible. If we do make devices with major or minor numbers above 255, and
then mount the file system with the old code, it'll just read the first
two bytes and get the numbers wrong. If it comes to garbage-collect it,
it'll then write back those wrong numbers. But that's about the best we
can expect.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

There is a second revision of "mtdconcat NAND/Sibley" patch. I hope
the patch will not get damaged as I'm posting it from gmail account,
thanks to Jorn.

The patch adds previously missing concat_writev(),
concat_writev_ecc(), concat_block_isbad(), concat_block_markbad()
functions to make concatenation layer compatible with Sibley and NAND
chips.

Patch has been cleared from whitespaces, fixed some lines of code as
requested. Also I have added code for alignment check that should
support Jorn's "writesize" patch.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The following difference was found between the mainline and linux-mips
kernel.  LASAT depends on MTD_CFI.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

In an unrelated MTD commit, a description about the ms02-nv module
got removed from Kconfig.  While I personally agree with this
removal, the module maintainer (Maciej W. Rozycki) would like to
see it added back.  In the absense of any consistency regarding
Kconfig descriptions his wish should be followed.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

'oobavail' parameter of mtd_info structure is now propagated to the MTD
partitions
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

This allows for much better abstraction and separation of the XIP and
non-XIP cases with their own specific implementations.  This fixes the
case where a timeout was tripped on in the XIP case by the code that
was meant for the non-XIP case only.

This also makes for a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
CC: "Alexey, Korolev" <alexey.korolev@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

... otherwise xip_enable() won't do the right thing.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The patch below fixes a potential starvation issue that can arise when
there is contention on a chip during a period when a process is
currently writing to it.  The starvation is avoided by conditionally
rescheduling when the chip is left in a state usable by other processes.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Tom Gall <tom_gall@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We have to pack at least the jint16_t structure, because otherwise it'll
be four bytes in size. Thankfully, we can do that and _not_ pack the
actual node structures, and the compiler still doesn't emit stupid code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

    On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
    So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
    There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Fix build warnings from drivers/mtd/redboot.c due to
use of `unsigned long` in `struct fis_image_desc` for
fields being passed to swab32s() which expects __u32 *

Change the entries to uint32_t to make them compatible
with the swab32s() function
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

     During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

fs/jffs2/summary.c: In function ‘jffs2_sum_write_data’:
fs/jffs2/summary.c:658: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘uint32_t’
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Mark certain functions with __init and __exit appropriately.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

On Mon, May 15, 2006 at 12:56:37AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.17-rc3-mm1:
>...
>  git-mtd.patch
>...
>  git trees
>...

If we correct the names of the config options, the code might actually
work as intended...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

If jffs2_scan_eraseblock() fails and the exit path is taken, 's' is not
being deallocated.

Reported by Coverity, CID: 1258.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

On alpha:

drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)

Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

fs/jffs2/nodelist.c: In function `check_node_data':
fs/jffs2/nodelist.c:441: warning: unsigned int format, different type arg (arg 4)
fs/jffs2/nodelist.c:464: warning: int format, different type arg (arg 5)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Changing the driver to use dynamic device numbers was one of the many
changes that were made in order to have the driver accepted into the
mainline kernel.  Therefore I would say that the entry in devices.txt is
obsolete.  This patch removes it.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Add the IBM microdrive to the known PCMCIA IDs for ide_cs.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix some typos in Documentation/memory-barriers.txt
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

HOTPLUG_CPU entry says "Say Y..." then "Say N.".  Slightly ugly, so I fixed
it up, and added remark about suspend on SMP as a bonus.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Do not enable the SMBus device on Asus boards if suspend is used.  We do
not reenable the device on resume, leading to all sorts of undesirable
effects, the worst being a total fan failure after resume on Samsung P35
laptop.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Revert commit f6422f17, due to

Valdis.Kletnieks@vt.edu wrote:
>
> There seems to have been a bug introduced in this changeset:
>
> Am running 2.6.17-rc3-mm1.  When this changeset is applied, 'mount --bind'
> misbehaves:
>
> > # mkdir /foo
> > # mount -t tmpfs -o rw,nosuid,nodev,noexec,noatime,nodiratime none /foo
> > # mkdir /foo/bar
> > # mount --bind /foo/bar /foo
> > # tail -2 /proc/mounts
> > none /foo tmpfs rw,nosuid,nodev,noexec,noatime,nodiratime 0 0
> > none /foo tmpfs rw 0 0
>
> Reverting this changeset causes both mounts to have the same options.
>
> (Thanks to Stephen Smalley for tracking down the changeset...)
>

Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When we fail to mount from a valid root device list out the filesystems we
have tried to mount it with.  This gives the user vital diagnostics as to
what is missing from their kernel.

For example in the fragment below the kernel does not have CRAMFS compiled
into the kernel and yet appears to recognise it at the RAMDISK detect
stage.  Later the mount fails as we don't have the filesystem.

  RAMDISK: cramfs filesystem found at block 0
  RAMDISK: Loading 1604KiB [1 disk] into ram disk... done.
  XFS: bad magic number
  XFS: SB validate failed
  No filesystem could mount root, tried: reiserfs ext3 ext2 msdos vfat
    iso9660 jfs xfs
  Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Mentioned by Mark Armbrust somewhere on Usenet.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>