This Fresco Logic xHCI host controller chip revision puts bad data into
the output endpoint context after a Reset Endpoint command.  It needs a
Configure Endpoint command (instead of a Set TR Dequeue Pointer command)
after the reset endpoint command.

Set up the input context before issuing the Reset Endpoint command so we
don't copy bad data from the output endpoint context.  The HW also can't
handle two commands queued at once, so submit the TRB for the Configure
Endpoint command in the event handler for the Reset Endpoint command.

Devices that stall on control endpoints before a configuration is selected
will not work under this Fresco Logic xHCI host controller revision.

This patch is for prototype hardware that will be given to other companies
for evaluation purposes only, and should not reach consumer hands.  Fresco
Logic's next chip rev should have this bug fixed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When a control endpoint stalls, the next control transfer will clear the
stall.  The USB core doesn't call down to the host controller driver's
endpoint_reset() method when control endpoints stall, so the xHCI driver
has to do all its stall handling for internal state in its interrupt handler.

When the host stalls on a control endpoint, it may stop on the data phase
or status phase of the control transfer.  Like other stalled endpoints,
the xHCI driver needs to queue a Reset Endpoint command and move the
hardware's control endpoint ring dequeue pointer past the failed control
transfer (with a Set TR Dequeue Pointer or a Configure Endpoint command).

Since the USB core doesn't call usb_hcd_reset_endpoint() for control
endpoints, we need to do this in interrupt context when we get notified of
the stalled transfer.  URBs may be queued to the hardware before these two
commands complete.  The endpoint queue will be restarted once both
commands complete.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Full speed devices have varying max packet sizes (8, 16, 32, or 64) for
endpoint 0.  The xHCI hardware needs to know the real max packet size
that the USB core discovers after it fetches the first 8 bytes of the
device descriptor.

In order to fix this without adding a new hook to host controller drivers,
the xHCI driver looks for an updated max packet size for control
endpoints.  If it finds an updated size, it issues an evaluate context
command and waits for that command to finish.  This should only happen in
the initialization and device descriptor fetching steps in the khubd
thread, so blocking should be fine.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Set the max packet size for the default control endpoint on high speed
devices to be 64 bytes.  High speed devices always have a max packet size
of 64 bytes.  There's no use setting it to eight for the initial 8 byte
descriptor fetch and then issuing (and waiting for) an evaluate context
command to update it to 64 bytes for the subsequent control transfers.

The USB core guesses that the max packet size on a full speed control
endpoint is 64 bytes, and then updates it after the first 8-byte
descriptor fetch.  Change the initial setup for the xHCI internal
representation of the full speed device to have a 64 byte max packet size.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Refactor out the code issue, wait for, and parse the event completion code
for a configure endpoint command.  Modify it to support the evaluate
context command, which has a very similar submission process.  Add
functions to copy parts of the output context into the input context
(which will be used in the evaluate context command).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use the virtual address of the memory hardware uses, not the address for
the container of that memory.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Different sections of the xHCI 0.95 specification had opposing
requirements for the chain bit in a link transaction request buffer (TRB).
The chain bit is used to designate that adjacent TRBs are all part of the
same scatter gather list that should be sent to the device.  Link TRBs can
be in the middle, or at the beginning or end of these chained TRBs.

Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the
chain bit set to 1", meaning it is always chained to the next TRB.
However, section 4.6.9 on the stop endpoint command has specific cases for
what the hardware must do for a link TRB with the chain bit set to 0.  The
0.96 specification errata later cleared up this issue by fixing the
4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain
bit set to 1 or 0.

The problem is that the xHCI cancellation code depends on the chain bit of
the link TRB being cleared when it's at the end of a TD, and some 0.95
xHCI hardware simply stops processing the ring when it encounters a link
TRB with the chain bit cleared.

Allow users who are testing 0.95 xHCI prototypes to set a module parameter
(link_quirk) to turn on this link TRB work around.  Cancellation may not
work if the ring is stopped exactly on a link TRB with chain bit set, but
cancellation should be a relatively uncommon case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

SL811 Device detected after removal used to be working in linux-2.6.22
but then broke somewhere between 2.6.22 and 2.6.28. Current
hub_port_connect_change() in drivers/usb/core/hub.c won't call
usb_disconnect() in case the SL811 driver sets portstatus
USB_PORT_FEAT_CONNECTION upon removal.
AFAIK the SL811 has only a combined Device Insert/Remove
detection bit, therefore use a count to distinguish insert or remove.
Signed-Off-By: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

cdc-acm needs to set a flag during open to tell the
tty layer that the device is initialized
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Paul Martin <pm@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

support for O_NONBLOCK in read and write path
by simply not waiting for data in read or availability
of the write urb in write but returning -EAGAIN
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The first open of the usb serial HW has the termios initialized to the
default of 9600 baud, and this will override what ever was setup via
the original console initialization.

The solution is to save the console baud rate and re-use it later on
the first open, so as to allow the use of baud rates other than 9600
for the usb serial console.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* Boot with the kernel argument console=ttyUSB0,9600
* Run: stty -a < /dev/ttyUSB0
* Immediately you get an oops warning, which later leads to a hard
  kernel crash

The commit 335f8514 created the
original regression and commit
6e406121 only fixed part of the
problem.

Only protect the serial->type->open() from getting executed when the
device is used as a console.

The wider scope of the console protection added in
6e406121 causes the logic in
serial_open() to fall through and zero out the port->port.count with
the stty sys call.  Once the port.count is zeroed the HW will get
closed while other drivers still have call backs to a non-initialized
device which crashes the kernel.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add ID for Telit UC-864G GPS/UMTS/WCDMA modem and GPS receiver
to the option driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A few days ago i got the latest ZTE EVDO modem shown at:
http://img.alibaba.com/photo/240150115/ZTE_AC2726_EVDO_USB_Data_Modem.jpg

It seems that the latest kernel does not have support for it.
I wrote a small patch for the options.c module to add the relevant usb
ids to it.

From: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Sanwa PC5000
mulitimeter with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In the resume path of a block driver GFP_NOIO must be used to
avoid a possible deadlock. The onetouch subdriver of storage violates
the requirement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add ID as reported in:

http://lists.infradead.org/pipermail/linux-pcmcia/2009-May/006127.htmlReported-by: Kenneth Moorman <KMoorman@transy.edu>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module.  Otherwise we get build failures due to the ifdef
handling.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The tty_operation chars_in_buffer() is not allowed to return a negative
value to signal an error.  Corrects the problem flagged by commit
23198fda, "tty: fix chars_in_buffers".
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Merge branch 'for-linus3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  SELinux: inline selinux_is_enabled in !CONFIG_SECURITY_SELINUX
  KEYS: Fix garbage collector
  KEYS: Unlock tasklist when exiting early from keyctl_session_to_parent
  CRED: Allow put_cred() to cope with a NULL groups list
  SELinux: flush the avc before disabling SELinux
  SELinux: seperate avc_cache flushing
  Creds: creds->security can be NULL is selinux is disabled

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (23 commits)
  at_hdmac: Rework suspend_late()/resume_early()
  PM: Reset transition_started at dpm_resume_noirq
  PM: Update kerneldoc comments in drivers/base/power/main.c
  PM: Add convenience macro to make switching to dev_pm_ops less error-prone
  hp-wmi: Switch driver to dev_pm_ops
  floppy: Switch driver to dev_pm_ops
  PM: Trivial fixes
  PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
  PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
  PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
  PM/Hibernate: Rework shrinking of memory
  PM: Fix typo in label name s/Platofrm_finish/Platform_finish/
  PM: Run-time PM platform device bus support
  PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
  Driver Core: Make PM operations a const pointer
  PM: Remove platform device suspend_late()/resume_early() V2
  USB: Rework musb suspend()/resume_early()
  I2C: Rework i2c-s3c2410 suspend_late()/resume() V2
  I2C: Rework i2c-pxa suspend_late()/resume_early()
  DMA: Rework txx9dmac suspend_late()/resume_early()
  ...

Fix trivial conflict in drivers/base/platform.c (due to same
constification patch being merged in both sides, along with some other
PM work in the PM branch)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig:
  kconfig: add missing dependency of conf to localyesconfig
  kconfig: test if a .config already exists
  kconfig: make local .config default for streamline_config
  kconfig: test for /boot/config-uname after /proc/config.gz in localconfig
  kconfig: unset IKCONFIG_PROC and clean up nesting
  kconfig: search for a config to base the local(mod|yes)config on
  kconfig: keep config.gz around even if CONFIG_IKCONFIG_PROC is not set
  kconfig: have extract-ikconfig read ELF files
  kconfig: add check if end exists in extract-ikconfig
  kconfig: enable CONFIG_IKCONFIG from streamline_config.pl
  kconfig: do not warn about modules built in
  kconfig: streamline_config.pl do not stop with no depends
  kconfig: add make localyesconfig option
  kconfig: make localmodconfig to run streamline_config.pl
  kconfig: add streamline_config.pl to scripts

Without this patch building a kernel emits millions of warning like:

include/linux/selinux.h:92: warning: ?selinux_is_enabled? defined but not used

When it is build without CONFIG_SECURITY_SELINUX.  This is harmless, but
the function should be inlined, so it gets compiled out.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
  Input: bcm5974 - silence uninitialized variables warnings
  Input: wistron_btns - add keymap for AOpen 1557
  Input: psmouse - use boolean type
  Input: i8042 - use platform_driver_probe
  Input: i8042 - use boolean type where it makes sense
  Input: i8042 - try disabling and re-enabling AUX port at close
  Input: pxa27x_keypad - allow modifying keymap from userspace
  Input: sunkbd - fix formatting
  Input: i8042 - bypass AUX IRQ delivery test on laptops
  Input: wacom_w8001 - simplify querying logic
  Input: atkbd - allow setting force-release bitmap via sysfs
  Input: w90p910_keypad - move a dereference below a NULL test
  Input: add twl4030_keypad driver
  Input: matrix-keypad - add function to build device keymap
  Input: tosakbd - fix cleaning up KEY_STROBEs after error
  Input: joydev - validate axis/button maps before clobbering current ones
  Input: xpad - add USB ID for the drumkit controller from Rock Band
  Input: w90p910_keypad - rename driver name to match platform
  Input: add new driver for Sentelic Finger Sensing Pad
  Input: psmouse - allow defining read-only attributes
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: completely remove apple mightymouse from blacklist
  HID: support larger reports than 64 bytes in hiddev
  HID: local function should be static
  HID: ignore Philips IEEE802.15.4 RF Dongle
  HID: ignore all recent SoundGraph iMON devices
  HID: fix memory leak on error patch in debug code
  HID: fix overrun in quirks initialization
  HID: Drop NULL test on list_entry result
  HID: driver for Twinhan USB 6253:0100 remote control
  HID: adding __init/__exit macros to module init/exit functions
  HID: add rumble support for Thrustmaster Dual Trigger 3-in-1
  HID: ntrig tool separation and pen usages
  HID: Avoid double spin_lock_init on usbhid->lock
  HID: add force feedback support for Logitech WingMan Formula Force GP
  HID: Support new variants of Samsung USB IR receiver (0419:0001)
  HID: fix memory leak on error path in debug code
  HID: fix debugfs build with !CONFIG_DEBUG_FS
  HID: use debugfs for events/reports dumping
  HID: use debugfs for report dumping descriptor

* 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block: (29 commits)
  block: use blkdev_issue_discard in blk_ioctl_discard
  Make DISCARD_BARRIER and DISCARD_NOBARRIER writes instead of reads
  block: don't assume device has a request list backing in nr_requests store
  block: Optimal I/O limit wrapper
  cfq: choose a new next_req when a request is dispatched
  Seperate read and write statistics of in_flight requests
  aoe: end barrier bios with EOPNOTSUPP
  block: trace bio queueing trial only when it occurs
  block: enable rq CPU completion affinity by default
  cfq: fix the log message after dispatched a request
  block: use printk_once
  cciss: memory leak in cciss_init_one()
  splice: update mtime and atime on files
  block: make blk_iopoll_prep_sched() follow normal 0/1 return convention
  cfq-iosched: get rid of must_alloc flag
  block: use interrupts disabled version of raise_softirq_irqoff()
  block: fix comment in blk-iopoll.c
  block: adjust default budget for blk-iopoll
  block: fix long lines in block/blk-iopoll.c
  block: add blk-iopoll, a NAPI like approach for block devices
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
  [SCSI] fix oops during scsi scanning
  [SCSI] libsrp: fix memory leak in srp_ring_free()
  [SCSI] libiscsi, bnx2i: make bound ep check common
  [SCSI] libiscsi: add completion function for drivers that do not need pdu processing
  [SCSI] scsi_dh_rdac: changes for rdac debug logging
  [SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
  [SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
  [SCSI] sg: fix oops in the error path in sg_build_indirect()
  [SCSI] mptsas : Bump version to 3.04.12
  [SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
  [SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
  [SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
  [SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
  [SCSI] mptsas : Sanity check for phyinfo is added
  [SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
  [SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
  [SCSI] qla2xxx: Update version number to 8.03.01-k6.
  [SCSI] qla2xxx: Properly delete rports attached to a vport.
  [SCSI] qla2xxx: Correct various NPIV issues.
  [SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
  ...

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Document the flex_array library.
  Doc: seq_file.txt fix wrong dd command example.

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
  [ARM] Update mach-types
  ARM: 5636/1: Move vendor enum to AMBA include
  ARM: Fix pfn_valid() for sparse memory
  [ARM] orion5x: Add LaCie NAS 2Big Network support
  [ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
  ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
  ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
  ARM: 5689/1: Update default config of HP Jornada 700-series machines
  ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
  ARM: 5688/1: ks8695_serial: disable_irq() lockup
  ARM: 5687/1: fix an oops with highmem
  ARM: 5684/1: Add nuc960 platform to w90x900
  ARM: 5683/1: Add nuc950 platform to w90x900
  ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
  ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
  ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
  MMC: MMCI: convert realview MMC to use gpiolib
  ARM: 5685/1: Make MMCI driver compile without gpiolib
  ARM: implement highpte
  ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
  ...

Fix up trivial conflict in arch/arm/kernel/signal.c.

It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83 ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.

My 353d5c30 "mm: fix hugetlb bug due to
user_shm_unlock call" broke the CONFIG_SYSVIPC !CONFIG_MMU build of both
2.6.31 and 2.6.30.6: "undefined reference to `user_shm_unlock'".

gcc didn't understand my comment! so couldn't figure out to optimize
away user_shm_unlock() from the error path in the hugetlb-less case, as
it does elsewhere.  Help it to do so, in a language it understands.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
  MAINTAINERS: update KVM entry
  KVM: correct error-handling code
  KVM: fix compile warnings on s390
  KVM: VMX: Check cpl before emulating debug register access
  KVM: fix misreporting of coalesced interrupts by kvm tracer
  KVM: x86: drop duplicate kvm_flush_remote_tlb calls
  KVM: VMX: call vmx_load_host_state() only if msr is cached
  KVM: VMX: Conditionally reload debug register 6
  KVM: Use thread debug register storage instead of kvm specific data
  KVM guest: do not batch pte updates from interrupt context
  KVM: Fix coalesced interrupt reporting in IOAPIC
  KVM guest: fix bogus wallclock physical address calculation
  KVM: VMX: Fix cr8 exiting control clobbering by EPT
  KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
  KVM: Document KVM_CAP_IRQCHIP
  KVM: Protect update_cr8_intercept() when running without an apic
  KVM: VMX: Fix EPT with WP bit change during paging
  KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
  KVM: x86 emulator: Add adc and sbb missing decoder flags
  KVM: Add missing #include
  ...

console_print() is an old legacy interface mostly unused in the entire
kernel tree. It's best to clean up its existing use and let developers
use their own implementation of it as they feel fit.
Signed-off-by: Anirban Sinha <asinha@zeugmasystems.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: fix slab_pad_check()
  slub: release kobject if sysfs_create_group failed in sysfs_slab_add
  SLUB: fix ARCH_KMALLOC_MINALIGN cases 64 and 256
  SLUB: Fix some coding style issues
  SLUB: Drop write permission to /proc/slabinfo
  slab: remove duplicate kmem_cache_init_late() declarations
  slub: change kmem_cache->align to record the real alignment
  slub: use size and objsize orders to disable debug flags
  slub: add option to disable higher order debugging slabs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  x86, mce: do not compile mcelog message on AMD
  EDAC, AMD: decode FR MCEs
  EDAC, AMD: decode load store MCEs
  EDAC, AMD: decode bus unit MCEs
  EDAC, AMD: decode instruction cache MCEs
  EDAC, AMD: decode data cache MCEs
  EDAC, AMD: carve out decoding of MCi_STATUS ErrorCode
  EDAC, AMD: carve out MCi_STATUS decoding
  x86, mce: pass mce info to EDAC for decoding
  amd64_edac: cleanup amd64_decode_bus_error
  amd64_edac: remove memory and GART TLB error decoders
  amd64_edac: cleanup/complete NB MCE decoding
  amd64_edac: cleanup amd64_process_error_info
  EDAC: beef up ErrorCodeExt error signatures
  EDAC: move MCE error descriptions to EDAC core

Fix a number of problems with the new key garbage collector:

 (1) A rogue semicolon in keyring_gc() was causing the initial count of dead
     keys to be miscalculated.

 (2) A missing return in keyring_gc() meant that under certain circumstances,
     the keyring semaphore would be unlocked twice.

 (3) The key serial tree iterator (key_garbage_collector()) part of the garbage
     collector has been modified to:

     (a) Complete each scan of the keyrings before setting the new timer.

     (b) Only set the new timer for keys that have yet to expire.  This means
         that the new timer is now calculated correctly, and the gc doesn't
         get into a loop continually scanning for keys that have expired, and
         preventing other things from happening, like RCU cleaning up the old
         keyring contents.

     (c) Perform an extra scan if any keys were garbage collected in this one
     	 as a key might become garbage during a scan, and (b) could mean we
     	 don't set the timer again.

 (4) Made key_schedule_gc() take the time at which to do a collection run,
     rather than the time at which the key expires.  This means the collection
     of dead keys (key type unregistered) can happen immediately.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

When we exit early from keyctl_session_to_parent because of permissions or
because the session keyring is the same as the parent, we need to unlock the
tasklist.

The missing unlock causes the system to hang completely when using
keyctl(KEYCTL_SESSION_TO_PARENT) with a keyring shared with the parent.
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

put_cred() will oops if given a NULL groups list, but that is now possible with
the existence of cred_alloc_blank(), as used in keyctl_session_to_parent().

Added in commit:

	commit ee18d64c
	Author: David Howells <dhowells@redhat.com>
	Date:   Wed Sep 2 09:14:21 2009 +0100
	KEYS: Add a keyctl to install a process's session keyring on its parent [try #6]
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>