Come out of i2c time out condition by following the
bus recovery procedure outlined in the i2c protocol v3 spec.
The kernel must be robust enough to gracefully recover
from i2c bus failure without having to reset the machine.
This is done by first NACKing the slave, pulsing the SCL
line 9 times and then sending the stop command.

This patch has been tested on a DM6446 and DM355
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Srinivasan, Nageswari <nageswari@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

Add cpufreq support for DaVinci I2C driver.
Tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

Add suspend and resume callbacks to DaVinci I2C driver.
This has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

Add i2c reset control and clock divider calculation functions
which will be useful for power management features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

Cleanup the DaVinci I2C driver. Remove MOD_REG_BIT macro.
Also use ioremap instead of IO_ADDRESS macro.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

This fixes Oops at kernel startup while "scanning" for TLV320AIC23IDx
addresses.

Additional fix from Sudhakar Rajashekhara: I think 'first byte set'
should come after the write because an I2C transaction is being
carried out before configuring the I2C mode register (which has bits
to configure Master, Start condition etc), which causes undefined
behavior.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Alexander Vasiliev <alexvasiljev@gmail.com>
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

The touch screen controller in the TPS6507x chip needs values that are
dependent on the characteristics of the touch screen hardware being used
in the board design.  In addition, the board provides version information
that is exposed via the kernel input sub-system.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

-V3 Add MFD driver for TPS6507x family of multi-function chips and move TPS6507x regulator driver from being stand-alone to using the MFD driver.

Add MFD driver for TPS6507x family of multi-function chips.  Move TPS6507x
regulator driver from being stand-alone driver to using the MFD TPS6507x driver.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>

Improve the suspend and resume callbacks in DaVinci MMC host controller driver.
Modify the reset status of the contorller and clock during suspend and resume.
Also migrate the power management callbacks from platform driver to dev_pm_ops
structure.

Tested on DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

Add a helper function which will aid in changing the reset
status of the controller.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

On some platforms like DM355, the number of EDMA parameter
slots available for EDMA_SLOT_ANY usage are few. In such cases,
if MMC/SD uses 16 slots for each instance of MMC controller,
then the number of slots available for other modules will be
very few.

By passing the number of EDMA slots to be used in MMC driver
from platform data, EDMA slots available for other purposes
can be controlled.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>

The rtc-omap driver currently hardcodes the RTC wakeup capability
to be "not capable". While this seems to be true for existing OMAP1
boards which are not wired for this, the DA850/OMAP-L138 SoC, the
RTC can always be wake up source from its "deep sleep" mode.

This patch lets the wakeup capability to be set from platform data and
does not override the setting from the driver. For DA850/OMAP-L138, this
is done from arch/arm/mach-davinci/devices-da8xx.c:da8xx_register_rtc()

Note that this patch does not change the behavior on any existing OMAP1
board since the platform device registration sets the wakeup capability
to 0 by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This reverts commit 9c0a342c because
it was included without proper signoffs from RTC maintainers.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  rtnetlink: make SR-IOV VF interface symmetric
  sctp: delete active ICMP proto unreachable timer when free transport
  tcp: fix MD5 (RFC2385) support

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Oprofile: Fix Loongson irq handler
  MIPS: N32: Use compat version for sys_ppoll.
  MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1

Now we have a set of nested attributes:

  IFLA_VFINFO_LIST (NESTED)
    IFLA_VF_INFO (NESTED)
      IFLA_VF_MAC
      IFLA_VF_VLAN
      IFLA_VF_TX_RATE

This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.

The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.

We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.

Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

    
    The interrupt enable bit for the performance counters is in the Control
    Register $24, not in the counter register.
    loongson2_perfcount_handler(), we need to use
Reported-by: Xu Hengyang <hengyang@mail.ustc.edu.cn>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
    Cc: linux-mips@linux-mips.org
    Patchwork: http://patchwork.linux-mips.org/patch/1198/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

    
    The sys_ppoll() takes struct 'struct timespec'. This is different for the
    N32 and N64 ABIs. Use the compat version to do the proper conversions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
    To: linux-mips@linux-mips.org
    Patchwork: http://patchwork.linux-mips.org/patch/1210/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

    
    In the FPU emulator code of the MIPS, the Cause bits of the FCSR register
    are not currently writeable by the ctc1 instruction.  In odd corner cases,
    this can cause problems.  For example, a case existed where a divide-by-zero
    exception was generated by the FPU, and the signal handler attempted to
    restore the FPU registers to their state before the exception occurred.  In
    this particular setup, writing the old value to the FCSR register would
    cause another divide-by-zero exception to occur immediately.  The solution
    is to change the ctc1 instruction emulator code to allow the Cause bits of
    the FCSR register to be writeable.  This is the behaviour of the hardware
    that the code is emulating.
    
    This problem was found by Shane McDonald, but the credit for the fix goes
    to Kevin Kissell.  In Kevin's words:
    
    I submit that the bug is indeed in that ctc_op:  case of the emulator.  The
    Cause bits (17:12) are supposed to be writable by that instruction, but the
    CTC1 emulation won't let them be updated by the instruction.  I think that
    actually if you just completely removed lines 387-388 [...] things would
    work a good deal better.  At least, it would be a more accurate emulation of
    the architecturally defined FPU.  If I wanted to be really, really pedantic
    (which I sometimes do), I'd also protect the reserved bits that aren't
    necessarily writable.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
    To: anemo@mba.ocn.ne.jp
    To: kevink@paralogos.com
    To: sshtylyov@mvista.com
    Patchwork: http://patchwork.linux-mips.org/patch/1205/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: check for read permission on src file in the clone ioctl

mempool_alloc() can return null in atomic case.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page().  Driver is able to compile now.

[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The existing code would have allowed you to clone a file that was
only open for writing
Signed-off-by: Chris Mason <chris.mason@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  JFS: Free sbi memory in error path
  fs/sysv: dereferencing ERR_PTR()
  Fix double-free in logfs
  Fix the regression created by "set S_DEAD on unlink()..." commit

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf record: Add a fallback to the reference relocation symbol

I spotted the missing kfree() while removing the BKL.

[akpm@linux-foundation.org: avoid multiple returns so it doesn't happen again]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

I moved the dir_put_page() inside the if condition so we don't dereference
"page", if it's an ERR_PTR().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

iput() is needed *until* we'd done successful d_alloc_root()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on.  To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question.  Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD.  Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.

2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint.  Fixed.

3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one.  Noticed and fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
  ARM: 6125/1: ARM TWD: move TWD registers to common header
  ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
  ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
  ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
  ARM: 6106/1: Implement copy_to_user_page() for noMMU
  ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c