- 04 Jul, 2009 15 commits
-
-
Mallikarjuna R Chilakala authored
Wake-on-lan is currently only supported by 82599 KX4 devices, in all other cases return a proper value from ixgbe_wol_exclusion function call. Otherwise from ethtool we will be able to change wol options of unsupported 8259x devices. Signed-off-by:
Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Don Skidmore authored
Currently if we loaded the driver, insert an unsupported module, and then attempt to "ifconfig up" the device it will be brought down but the netdev would not be unregistered. This behavior is different than all other code paths. This patch corrects that by down'ing the device and then scheduling the sfp_config_module_task tasklet. The tasklet will detect this condition (like it does with other code paths) and do the unregister_netdev(). I also removed the log message as this condition (an unsupported SFP+ module) will be logged in sfp_config_module_task. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by:
-
Don Skidmore authored
The change to check the SFP+ module again on open() was causing the XFP (non-SFP+) adapters to be rejected. We only want to try and re-identify the SFP+ module if the original probe found that this device was an SFP+ device. So for this code path (driver loaded with SFP module, module inserted, ifconfig up of the device) the type will be ixgbe_phy_unknown for an unidentified SFP+ module. So we only check if that is the case. This problem also shows up on Copper devices. Signed-off-by:
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by:
-
Don Skidmore authored
Several small fixes around negative test case of the insertion of a IXGBE_ERR_NOT_SUPPORTED module. - mdio45_probe call was always failing due to mdio.prtad not being set. The function set to mdio.mdio_read was still working as we just happen to always be at prtad == 0. This will allow us to set the phy_id and phy.type correctly now. - There was timing issue with i2c calls when initiated from a tasklet. A small delay was added to allow the electrical oscillation to calm down. - Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition to be recognized. Signed-off-by:
-
Ron Mercer authored
Some usage was only sizing a pointer rather than the data type. Signed-off-by:
Ron Mercer <ron.mercer@qlogic.com> Signed-off-by:
-
Ron Mercer authored
We need to set/clear the mac address register when the link goes up/down respectively. Without this both ports of a 2-port device can end up with the same mac address in a bonding scenario. The new ql_link_on() and ql_link_off() will also be used in handling certain firmware events. Signed-off-by:
-
Ron Mercer authored
This addes functionality to set/clear the MAC address in the hardware when the link goes up/down. The MAC address register is persistent across function resets. In bonding the same address can bounce from one port to the other. This can cause packets to be delivered to the wrong port. This patch clears the MAC address in the hardware when the link is down and sets it when the link comes up. It was found that pulling/pushing the cable from one port to another causes the same MAC address to be in both ports. The next patch in this series will use this functionality as well. Signed-off-by:
-
Ron Mercer authored
Signed-off-by:
-
Ron Mercer authored
The caller will free acquired resouces if a failure occurs. Signed-off-by:
-
Ron Mercer authored
We were turning on the carrier without verifying the link was up. This adds link up to the link initialize check before turning carrier on. Signed-off-by:
-
Ron Mercer authored
Not clearing the routing bits can cause frames to erroneously get routed to management processor. Signed-off-by:
-
Ron Mercer authored
The hardware semaphore covers the configuration register as well as the ICB registers. The ICB high and low regs contain the address of the initialization control block and the config register is used to signal the hardware that a block is ready to be downloaded. Currently we were only protecting the ICB regs. This changes expands to cover the config register as well. Signed-off-by:
-
Brian Haley authored
There's a bug in addrconf_prefix_rcv() where it won't update the preferred lifetime of an IPv6 address if the current valid lifetime of the address is less than 2 hours (the minimum value in the RA). For example, If I send a router advertisement with a prefix that has valid lifetime = preferred lifetime = 2 hours we'll build this address: 3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000 inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic valid_lft 7175sec preferred_lft 7175sec If I then send the same prefix with valid lifetime = preferred lifetime = 0 it will be ignored since the minimum valid lifetime is 2 hours: 3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000 inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic valid_lft 7161sec preferred_lft 7161sec But according to RFC 4862 we should always reset the preferred lifetime even if the valid lifetime is invalid, which would cause the address to immediately get deprecated. So with this patch we'd see this: 5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000 inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic valid_lft 7163sec preferred_lft 0sec The comment winds-up being 5x the size of the code to fix the problem. Update the preferred lifetime of IPv6 addresses derived from a prefix info option in a router advertisement even if the valid lifetime in the option is invalid, as specified in RFC 4862 Section 5.5.3e. Fixes an issue where an address will not immediately become deprecated. Reported by Jens Rosenboom. Signed-off-by:Brian Haley <brian.haley@hp.com> Signed-off-by:
-
Wei Yongjun authored
The SCTP pushed the skb above the sctp chunk header, so the check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in _decode_session6() will never return 0 and the ports decode of sctp will always fail. (nh + offset + 1 - skb->data < 0) Signed-off-by:
Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Wei Yongjun authored
The SCTP pushed the skb data above the sctp chunk header, so the check of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will never return 0 because xprth + 4 - skb->data < 0, the ports decode of sctp will always fail. Signed-off-by:
-
- 02 Jul, 2009 7 commits
-
-
Abhishek Kulkarni authored
It is not safe to use match_int without checking the token type returned by match_token (especially when the token type returned is Opt_err and args is empty). Fix it. Signed-off-by:
Abhishek Kulkarni <adkulkar@umail.iu.edu> Signed-off-by:
-
Alexander Duyck authored
This patch adds ETH_P_1588 protocol ID define. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
-
Wade Farnsworth authored
The PHY_HALTED state disables phydev->link, but the link will not be updated upon entering PHY_RESUMING. Add a call to phy_read_status() to update the link before entering PHY_RUNNING. If the link is not up at this point, enter the PHY_NOLINK state instead. Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to netif_carrier_on() and phydev->adjust_link() are missing. Add the calls similar to the other transitions to PHY_RUNNING. Signed-off-by:
Wade Farnsworth <wfarnsworth@mvista.com> Acked-by:
Andy Fleming <afleming@freescale.com> Signed-off-by:
-
Dhananjay Phadke authored
Restrict firmware reset to following cases - o chip rev is NX2031 (firmare doesn't support heartbit). o firmware is dead. o previous attempt to init firmware had failed. o we have got newer file firmware. This speeds up module load tremendously (by upto 8 sec), also avoids downtime for NCSI (management) pass-thru traffic. Signed-off-by:
Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by:
-
Dhananjay Phadke authored
Correct firmware encoding is 8 bit major, 8 bit minor and 16 bit subversion. Flash has sizes rightly set, but original driver submission messed it leaving 16 bit major and 8 bit subversion. Also fix a infinite loop when cut-thru file firmware is invalid. Signed-off-by:
-
Tilman Schmidt authored
Drop a sanity check which doesn't serve any useful purpose anymore. Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Signed-off-by:
-
Tilman Schmidt authored
ISDN connection setup failed if the "connection active" and "B channel up" messages from the device arrived in a different order than expected. Modify the state machine to accept them in any order. Impact: bugfix Signed-off-by:
-
- 01 Jul, 2009 17 commits
-
-
Eric W. Biederman authored
This reverts commit 73ce7b01. After discovering that we don't listen to gratuitious arps in 2.6.30 I tracked the failure down to this commit. The patch makes absolutely no sense. RFC2131 RFC3927 and RFC5227. are all in agreement that an arp request with sip == 0 should be used for the probe (to prevent learning) and an arp request with sip == tip should be used for the gratitous announcement that people can learn from. It appears the author of the broken patch got those two cases confused and modified the code to drop all gratuitous arp traffic. Ouch! Cc: stable@kernel.org Signed-off-by:
Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by:
-
Alexander Duyck authored
PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This patch fixes the issue for igb. Signed-off-by:
-
Mike Mason authored
on permanent failure PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This state is not checked in many of the network drivers. This patch fixes the omission in the e1000e driver. Signed-off-by:
Mike Mason <mmlnx@us.ibm.com> Signed-off-by:
-
Andre Detsch authored
PCI drivers that implement the io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is pci_channel_io_perm_failure. This state is not checked in many of the network drivers. The patch fixes the omission in the e1000 driver. Based on Mike Mason's similar patch for e1000e. Signed-off-by:
Andre Detsch <adetsch@br.ibm.com> CC: Mike Mason <mmlnx@us.ibm.com> Signed-off-by:
-
Jesse Brandeburg authored
as reported by kerneloops.org [ 121.781161] ------------[ cut here ]------------ [ 121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577() [ 121.781173] Hardware name: S5520HC [ 121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x00000001d688b0fa] [size=1522 bytes] [ 121.781180] Modules linked in: e1000 mdio dca [last unloaded: ixgbe] [ 121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3 [ 121.781190] Call Trace: [ 121.781195] [<ffffffff8123056f>] ? check_unmap+0x14e/0x577 [ 121.781201] [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f [ 121.781205] [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1 [ 121.781212] [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49 [ 121.781216] [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33 [ 121.781220] [<ffffffff8123056f>] check_unmap+0x14e/0x577 [ 121.781225] [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb [ 121.781230] [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92 [ 121.781234] [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e [ 121.781239] [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78 [ 121.781250] [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000] [ 121.781259] [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000] [ 121.781268] [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000] [ 121.781277] [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000] [ 121.781286] [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000] [ 121.781296] [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000] [ 121.781301] [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe [ 121.781305] [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1 [ 121.781310] [<ffffffff812eaf1c>] pm_op+0x57/0xde [ 121.781314] [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470 [ 121.781319] [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2 [ 121.781323] [<ffffffff81087a0f>] enter_state+0xd1/0x127 [ 121.781327] [<ffffffff8108717a>] state_store+0xa7/0xc9 [ 121.781332] [<ffffffff81221843>] kobj_attr_store+0x17/0x19 [ 121.781336] [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121 [ 121.781341] [<ffffffff810ed165>] vfs_write+0xab/0x105 [ 121.781344] [<ffffffff810ed279>] sys_write+0x47/0x6d [ 121.781349] [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b [ 121.781352] ---[ end trace 97bacaaac2ed7786 ]--- Fix is to correctly zero out internal ->dma value when unmapping and make sure never to unmap unless there specifically was a mapping done. Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls unevenly. Only map the bytes that the hardware might dma into also fix unmap related bug where ->dma was not being cleared after unmap Signed-off-by:
-
Jesse Brandeburg authored
This patch addresses three WARN_ON statements from DMA-API debug code ixgbe is mapping more than it unmaps, reduce the length of the map call and remove the "used once" local variable. found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate for -stable. in addition, fix missing ->dma = 0 after unmap to prevent double free with pci_unmap_single and lastly, don't unmap (half) pages that aren't mapped. Signed-off-by:
-
Mallikarjuna R Chilakala authored
Adapter link advertisement capabilities were not persistent during adapter resets. While configuring multispeed fiber link check for phy autoneg_advertised settings before overwriting with default link capabilities Signed-off-by:
-
Mallikarjuna R Chilakala authored
82599 single speed fiber modules only support 10G/Full. Return proper device capabilities while querrying the adapter and error while changing device advertisement/speed/duplex capabilities. Signed-off-by:
-
Don Skidmore authored
We had a wide range of log messages for the same sort of SFP failure. This patch makes them all more similar and less confusing along with converting them to dev_err. Signed-off-by:
-
Herbert Xu authored
Now that nothing uses the private stats structure we can remove it. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
Herbert Xu authored
Now that netdev has its own stats structure we should use that instead. Signed-off-by:
-
- 30 Jun, 2009 1 commit
-
-
Jarek Poplawski authored
Alas current delaying of freeing old tnodes by RCU in trie_rebalance is still not enough because we can free a top tnode before updating a t->trie pointer. Reported-by:
Pawel Staszewski <pstaszewski@itcare.pl> Tested-by:
Jarek Poplawski <jarkao2@gmail.com> Signed-off-by:
-
