- 23 Jun, 2009 40 commits
-
-
Mike Isely authored
The cx25840 module requires that its VBI initialization entry point be called in order for hardware-scaled video capture to work properly - even if we don't care about VBI. Making this behavior even more subtle is that if the capture resolution is set to 720x480 - which is the default that the pvrusb2 driver sets up - then the cx25840 bypasses the hardware scaler. Therefore this problem does not manifest itself until some other resolution, e.g. 640x480, is tried. MythTV typically defaults to 640x480 or 480x480, which means that things break whenever the driver is used with MythTV. This all has been known for a while (since at least Nov 2006), but recent changes in the pvrusb2 driver (specifically in regards to sub-device support) caused this to break again. VBI initialization must happen *after* the chip's firmware is loaded, not before. With this fix, 24xxx devices work correctly again. A related fix that is part of this changeset is that now we re-initialize VBI any time after we issue a reset to the cx25840 driver. Issuing a chip reset erases the state that the VBI setup previously did. Until the HVR-1950 came along this subtlety went unnoticed, because the pvrusb2 driver previously never issued such a reset. But with the HVR-1950 we have to do that reset in order to correctly transition from digital back to analog mode - and since the HVR-1950 always starts in digital mode (required for the DVB side to initialize correctly) then this device has never had a chance to work correctly in analog mode! Analog capture on the HVR-1950 has been broken this *ENTIRE* time. I had missed it until now because I've usually been testing at the default 720x480 resolution which does not require scaling... What fun. By re-initializing VBI after a cx25840 chip reset, correct behavior is restored. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michael Krufky authored
Ensure that we're programming the tda18271 tuner with the correct IF frequencies to match the programming of the TDA10048 DVB-T demod for the HVR1200 and HVR1700 products. Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Thanks for Terry Wu for pointing out the missing entry. Cc: Terry Wu <terrywu2009@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The variable 'rc' could be used uninitialized in the cx231xx_capture_start function. Sri informed me that it should be initialized to -1. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
tcm825x_remove is not necessarily called on module exit, it can also be called when the i2c_adapter is removed. While the i2c adapter might never be removed on an embedded system, in practice this sensor driver can also be used in e.g. a USB webcam where this is a perfectly acceptable thing to do. Signed-off-by:
-
Hans Verkuil authored
rxsubchans was only set when stereo was detected, otherwise it was left to 0 instead of setting it to mono. Signed-off-by:
-
Hans Verkuil authored
Make it very clear that this header should not be used for i2c drivers that do not need to be compiled for pre-2.6.26 kernels. As soon as the minimum supported kernel in the v4l-dvb repository becomes 2.6.26 or up, then this header should be removed entirely. Signed-off-by:
-
Hans Verkuil authored
gcc 4.3.1 generates this warning: v4l/smscoreapi.c: In function 'smscore_gpio_configure': v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function While in practice this will not happen, it is something that the compiler can't determine. Initializing these two local variables to 0 suppresses this warning. Cc: Udi Atar <udi.linuxtv@gmail.com> Signed-off-by:
-
Hans Verkuil authored
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control was broken for all drivers that use the cx2341x module and the USER class control was broken for ivtv and cx18. This change adds back proper class control support. Signed-off-by:
-
Devin Heitmueller authored
Add an IR profile for the EVGA inDtube remote control (which is an NEC type remote) Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Add support for the EVGA inDtube. Both ATSC and analog side validated as fully functional. Thanks to Jake Crimmins from EVGA for providing the correct GPIO info. Thanks to Alan Hagge for doing all the device testing. Thanks to Greg Williamson for providing hardware for testing. Cc: Jake Crimmins <jcrimmins@evga.com> Cc: Alan Hagge <ahagge@gmail.com> Cc: Greg Williamson <cheeseboy16@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
In cases where the board had a default USB ID, we would not indentify the board until after the call to em28xx_set_mode(). As a result, for those boards the analog GPIOs were not being set before probing the i2c bus for devices (the probe would occur with the GPIOs being all high). Make a call to em28xx_set_mode() so that the GPIOs are set properly before probing the i2c bus for devices. This problem was detected with the EVGA inDtube, where the tvp5150 is not powered on unless GPIO1 is pulled low. Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
Igor M. Liplianin <liplianin@netup.ru> Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
Abylay Ospan <aospan@netup.ru> Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Hans de Goede authored
Name saturation control saturation, not color and make the default less saturated (the old default was overdoing it). Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise the picture is upside down. It is better to instead invert the meaning of the control in the set function, and have the default be no vflip, as one would expect vflip enabled to be upside down. Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: Add light frequency control Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: enable autogain control for the ov7620, and not only make it enable autogain but also auto exposure (and do the same for the ov7648). Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer overflows during my testing of a "Premier" 0c45:613e cam Signed-off-by:
-
Hans de Goede authored
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one cam it supports, is now also supported by the v4l2 gspca stv06xx driver. Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak the ov7630 register init values for a much better picture. Signed-off-by:
-
Hans de Goede authored
The control index defines for the gspca_sonixj driver were numbered wrong, causing us to disable the wrong controls on various sensors Signed-off-by:
-
Hans de Goede authored
gspca_ov519: constify ov518 inititial register value tables Signed-off-by:
-
Hans de Goede authored
Mark the v4l1 ov511 as deprecated as we now have ov511 support in the gspca ov519 driver. Note we should really also keep track of this in Documentation/feature-removal-schedule.txt, but that is not part of the v4l-dvb tree. Signed-off-by:
-
Hans de Goede authored
ov511: remove ov518 usb id's from the driver, as they have not been working ever since the decompression code got removed from the kernel, and they are no supported by the gspca_ov519 module. Signed-off-by:
-
Hans de Goede authored
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver, tested with: Logitech QuickCam Messenger 046d:08f0 ST6422 integrated Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated Signed-off-by:
-
Hans de Goede authored
gspca_ov519: Cleanup some sensor special cases Signed-off-by:
-
Hans de Goede authored
gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320) Signed-off-by:
-
Hans de Goede authored
gspca_ov519: add support for the ov511 bridge Signed-off-by:
-
Hans de Goede authored
Hmm, another one with an extra if (life sucks) the default contrast really is no good for the ov6630, it isn't even high enough in full daylight, this gives the ov6630 a different initial value for a better out of the box experience. Signed-off-by:
-
Hans de Goede authored
As reported on the ov51x-jpeg list, and as I can confirm with my own cam the ov7670 in 320x240 has a number of broken columns of pixels at the left of the picture. This was not present in the old driver as it always used 640x480 and did software downscaling (took me a while to figure that one out). The fix adds a sensor specific if in so far sensor neutral code :( But this is the only way to fix this, this cannot be fixed by only changing sensor registers. Signed-off-by:
-
Hans de Goede authored
My ov519 cam has it led inverted, the same has been reported on the ov51x-jpeg list for another creative cam. This patch fixes this without changing the behaviour for other cams. Signed-off-by:
-
Hans de Goede authored
Check ov518 packet numbers to detect dropped packets. Signed-off-by:
-
Hans de Goede authored
gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams Signed-off-by:
-
Hans de Goede authored
The fix for the UV swapping in qcif mode with the ov6630, which I did to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in qcif with another cam of mine with the ov518 and an ov66308AE, so this patch changes the code to differentiate between the ov66308AF and other ov6630 versions, and restricts the UV swap fix to the ov66308AF. Signed-off-by:
-
Hans de Goede authored
This patch adds autobrightness (so that it can be turned off to make the already present brightness control work) and light frequency filtering controls. The lightfreq control needed 2 different entries in the ctrls array, as the number of options differs depending on the sensor. Always one of the 2 entires is disabled ofcourse. Signed-off-by:
-
Hans de Goede authored
gspca: fix NULL pointer deref in query_ctrl Signed-off-by:
-
Mauro Carvalho Chehab authored
Fix Leadtek TV2000 XP Global entries and add missing PCI ID's. Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings. Cc: Terry Wu <terrywu2009@gmail.com> Signed-off-by:
-
