- 24 Apr, 2008 40 commits
-
-
Alexander Simon authored
Alexander Simon found out that the Terratec Cinergy T USB XXS is just a clone of another DiB7070P-based device. Signed-off-by:
Patrick Boettcher <pb@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Patrick Boettcher authored
This patch enables support for repeating last event when a key is holded down with dib0700 devices. It works with rc5 and nec remotes. It also fixes an annoying bug that floods kernel log with "Unknown key" messages after each keypress. This happened because the driver was not resetting infrared register after each poll so it kept polling last key even if nothing was being pressed. Fixing this, (calling rc_setup after each poll), permits to implement key repeat. Signed-off-by: Filippo Argiolas <filippo.argiolas at gmail.com> Signed-off-by:
-
Albert Comerma authored
This patch introduces support for dvb-t for the following DiBcom based cards: - Terratec Cinergy HT USB XE (USB-ID: 0ccd:0058) - Terratec Cinergy HT Express (USB-ID: 0ccd:0060) - Pinnacle 320CX (USB-ID: 2304:022e) - Pinnacle PCTV72e (USB-ID: 2304:0236) - Pinnacle PCTV73e (USB-ID: 2304:0237) - Yuan EC372S (USB-ID: 1164:1edc) Signed-off-by:
Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by:
Felix Apitzsch <F.Apitzsch@soz.uni-frankfurt.de> Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Albert Comerma <albert.comerma@gmail.com> Signed-off-by:
-
Andre Weidemann authored
Added support for Technotrend connect S-2400. Signed-off-by:
Andre Weidemann <Andre.Weidemann@web.de> Signed-off-by:
-
Patrick Boettcher authored
To support a new device based on CX24123 (using the CX24113-tuner) the following was done: - added two parameters to de-select the internal PLL-driver (for CX24108) and a AGC-function callback. - added a virtual i2c-adapter which allow simple access behind the i2c-gate - cleanup up some code Signed-off-by:
-
Patrick Boettcher authored
To prepare the support for new device to the flexcop-family some preparation and cleanups was done + some saneness: - created an i2c-adapter for each i2c-port available. Easier usage for devices with several device on different i2c-busses - initialize i2c before doing the eeprom read - changed the way to attach the different frontends, easier to read now - enabled support for i2c-devices having no register address (1-byte access) Signed-off-by:
-
Frej Drejhammar authored
An enabled color killer will not degrade picture quality for color input signals, only suppress bogus color information on black-and-white input. Therefore enable it by default. Signed-off-by:
Frej Drejhammar <frej.drejhammar@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Thanks to Cyrill Gorcunov <gorcunov@gmail.com> for pointing this Signed-off-by: -
Roel Kluin authored
include/linux/video_decoder.h: 34:#define DECODER_SET_NORM _IOW('d', 3, int) 35:#define DECODER_SET_INPUT _IOW('d', 4, int) untested, please confirm it's right. Test cmd value, not definition of DECODER_SET_INPUT Signed-off-by:Roel Kluin <12o3l@tiscali.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
Thanks to timf <timf@iinet.net.au>, "Richard (MQ)" <osl2008@googlemail.com> and gian luca rasponi <lucarasp@inwind.it> for their tests. Signed-off-by: -
Mauro Carvalho Chehab authored
Thanks to Jiri Slaby <jirislaby@gmail.com> for pointing this issue. Signed-off-by: -
Mauro Carvalho Chehab authored
Thanks to Michael Krufky for pointing this. Signed-off-by: -
Frej Drejhammar authored
The cx2388x family has a color killer. This patch implements the V4L2_CID_COLOR_KILLER control for the cx2388x family. By default the color killer is disabled, as in previous versions of the driver. Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>" Signed-off-by: -
Frej Drejhammar authored
Define a pre-defined control ID for color killer functionality. Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>" Signed-off-by: -
Frej Drejhammar authored
An enabled chroma AGC will not degrade picture quality if enabled on a color PAL or NTSC signal with nominal signal levels. It will give a significant color reproduction improvement if the chroma signals diverge from nominal levels. Therefore enable chroma AGC by default for PAL and NTSC standards. Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>" Signed-off-by: -
Frej Drejhammar authored
The cx2388x family has support for chroma AGC. This patch implements a the V4L2_CID_CHROMA_AGC control for the cx2388x family. By default chroma AGC is disabled, as in previous versions of the driver. Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>" Signed-off-by: -
Frej Drejhammar authored
Define a pre-defined control ID for chroma automatic gain control. Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>" Signed-off-by: -
Marton Balint authored
If the IR worker is not stopped before the removal of the cx88xx module, an OOPS may occur, because the worker function cx88_ir_work gets called. So stop the ir worker. Signed-off-by:
Marton Balint <cus@fazekas.hu> Signed-off-by:
-
Mauro Carvalho Chehab authored
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018). This patch adds proper support for radio, video, s-video, composite and ATSC. However, support for radio and video depends on having s5h1409 i2c gate open, otherwise, xc30x8 chip won't be visible. For a better support, some rework is needed on cx88 driver, to allow adding xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address. Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure out the proper parameters for s5h1409 and the GPIO pins used by each configuration. Signed-off-by: -
Mike Isely authored
Fix use of a non-int (size_t) being passed in a printf width field. This benign issue has apparently been around for a long time, but went undetected until now. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Michael Krufky authored
Update Kconfig for the hybrid devices recently converted to use tuner-simple rather than dvb-pll. dvb-bt8xx no longer uses dvb-pll at all, so remove all references to dvb-pll within that driver. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
Fix the following build error: In file included from dvb-bt8xx.c:35: dvb-bt8xx.h:42:26: error: tuner-simple.h: No such file or directory dvb-bt8xx.c: In function 'frontend_init': dvb-bt8xx.c:612: error: 'simple_tuner_attach' undeclared (first use in this function) dvb-bt8xx.c:612: error: (Each undeclared identifier is reported only once dvb-bt8xx.c:612: error: for each function it appears in.) dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of '__a' dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name' dvb-bt8xx.c:612: warning: cast from pointer to integer of different size dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name' dvb-bt8xx.c:612: warning: cast from pointer to integer of different size dvb-bt8xx.c:612: error: called object '__a' is not a function dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of '__a' dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name' dvb-bt8xx.c:696: warning: cast from pointer to integer of different size dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name' dvb-bt8xx.c:696: warning: cast from pointer to integer of different size dvb-bt8xx.c:696: error: called object '__a' is not a function Signed-off-by:
-
Mauro Carvalho Chehab authored
There are a number of different firmware versions and variants, shipped together with boards. This patch adds an extra parameter to the tuner-xc2028 to allow specifying for an specific firmware name to be loaded. This helps to test for a firmware that better fits some board. Signed-off-by: -
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Force the main pll charge pump or cal pll charge pump to source current to the main pll loop filter or cal pll loop filter, respectively. Signed-off-by:
-
Michael Krufky authored
Set rfagc to high speed mode before setting the pll. Set rfagc to normal speed mode at the end of the function. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
allow device-specific configuration of rf agc rf top and if top Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
The internal calibration signal must be set on the cal pll. Signed-off-by:
-
Michael Krufky authored
Both the tda18271 c1 and c2 parts only need EP3 through MD3 to be written for the image rejection calibration's low band initialization. Signed-off-by:
-
Michael Krufky authored
The ability to select RF input was a supported feature only available on Philips TUV1236d and Philips FCV1236d. This feature, along with support for the tuners that used it, was moved into the tuner-simple module. This can now be removed from dvb-pll. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
remove #if 0'd support for: Philips TUV1236D Philips TD1316 Philips FMD1216ME LG TDVS-H06xF Philips FCV1236D Thomson FE6600 Microtune 4042 FI5 Thomson dtt761x Support for these tuners has been moved into the 'tuner-simple' module. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
