This fixes Oops at kernel startup while "scanning" for TLV320AIC23IDx
addresses.
Signed-off-by: Alexander Vasiliev <alexvasiljev@gmail.com>
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

The Neuros OSD 2.0 is the hardware component of the Neuros Open
Internet Television Platform. Hardware is very close to Ti DM644X-EVM board.
It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
Additionaly realtime clock, IR remote control receiver,
IR Blaster based on MSP430 (firmware although is different
from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
with PATA interface, two muxed red-green leds.

For more information please refer to
	http://wiki.neurostechnology.com/index.php/OSD_2.0_HDSigned-off-by: Andrey Porodko <panda@chelcom.ru>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch fixes the following warning:

arch/arm/mach-davinci/board-sffsdr.c:99: warning: 'sffsdr_emac_pdata' defined but not used
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

A section mismatch is reported for gpio_led_platform_data
as it is referenced by a non annotated function (evm_led_setup)

This patch fixes the issue by converting the __initconst to const
as is the case in arch/arm/mach-davinci/board-dm644x-evm.c file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Using a device_initcall() for initializing the voltage regulator
on DA850 is not such a good idea because it gets called for all
platforms - even those who do not have a regulator implemented.
This leads to a big fat warning message during boot-up when
regulator cannot be found.

Instead, tie initialization of voltage regulator to cpufreq init.
Define a platform specific init call which in case of DA850 gets
used for initializing the regulator. On other future platforms it
can be used for other purposes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch provides a function to help register cpuidle driver
on da8xx/omap-l1xx platforms.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The patch adds support for DaVinci cpu idle driver.

Two idle states are defined:
1. Wait for interrupt
2. Wait for interrupt and DDR self-refresh (or power down)

Some DaVinci SoCs support putting DDR in self-refresh (eg Dm644x, DM6467)
while others support putting DDR in self-refresh and power down (eg DM35x,
DA8xx).

Putting DDR (or mDDR) in power down saves more power than self-refresh.

The patch has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:

WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.

This patch fixes such warnings.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Eliminate the static function declaration by rearranging
data in da850/omap-l138 board file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

There are multiple steps in configuring the EMAC to MII or RMII mode.
Current code implements them using multiple checks.

Consolidate the multiple checks into a single if construct.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Get rid of DA850_UI_EXP config option since it is not used anywhere
else in code.

Instead make the UI expander choice menu dependent on the EVM
selection itself.

Also add help text indicating that UI board is actually detected
automatically.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Implement autodetection of RMII PHY by shifting the decision
to use the RMII PHY to da850_evm_ui_expander_setup() from
da850_evm_init() earlier.

Without this patch, selecting RMII PHY in the UI expander menu
will make the MII PHY unusable even though UI board is not
connected.

The actual configuration and registration of the EMAC device
is delayed to device_initcall() so it happens after the UI card
detection is complete.

A side effect of this patch is the removal of a voilation of
Documentation/SubmittingPatches section 2.2 in function
da850_evm_init()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

On the DA830, AEMIF and MMC/SD pins are shared. On the EVM, when
the mux_mode signal is low MMC/SD works and when mux_mode signal
is high, NAND works.

When MMC/SD driver is configured in the kernel, do not let NAND
get registered and drive mux_mode high. Instead, print a warning
for user to understand why the platform device for NAND did not
get registered.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch supports runtime detection of DA830 UI card and
eliminates the need for DA830_UI config option. Successful
probe of GPIO expander present on the UI card is used to
detect its presence. For this reason, GPIO_PCF857X is auto-
selected when DA830 EVM is configured. In case the UI card
is absent, the probe fails in reasonable time.

As a side effect this patch also gets rid of the voilation
of Documentation/SubmittingPatches section 2.2 in function
da830_evm_ui_expander_setup()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Remove ifdefs inside da830_evm_init function since they are
discouraged in Documentation/SubmittingPatches section 2.2

Use the method outlined in that document for fixing it.

Tested on DA830 EVM.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch fixes the following warning seen when building with default
config:

arch/arm/mach-davinci/board-da830-evm.c:371: warning: 'da830_evm_devices' defined but not used

Tested on DA830 EVM with and without CONFIG_DA830_UI_NAND enabled.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add support for NAND flash parts on the DA830/OMAP-L137 EVM
User Interface board.  This includes overriding the default
bad block tables used by the davinci_nand driver.
Signed-off-by: David A. Griego <dgriego@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Properly set up the OTG mode thru the CFGCHIP2 register, enable the
USB0_DRVVBUS pin, and finally register the MUSB platform device.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Add the function to register the MUSB platform device.
Additional compile warning fixes by Sekhar Nori.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Rename setup_usb() into davinci_setup_usb().  While at it:

- move its declaration from <mach/common.h> to more fitting <mach/usb.h>;
- teach it to handle values of the 'mA' parameter greater than 510 and thus
  pass 1000 instead of 500 for the power switches capable of sourcing over 1 A;
- teach it to handle odd values of the 'potpgt_ms' parameter...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The general structures are defined at DM365 SoC file and the specific
platform data structure for the EVM is defined at board file.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>

DMx:
- enable MMC and dm365evm_keys
- Enable DM355 and DM365 input drivers as modules.

da8xx
- combine da830 and da850 into common defconfig
- drop SYSFS_DEPRECATED flag
- auto-select D$ writethrough for da830
- enable CPUfreq and FB
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

In the McASP clock definition add a flag to indicate that the peripheral clock
belongs to ASYNC3 clock domain.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch adds platform data and partition info for NAND on dm6467 EVM.

Note that the partition layout is dependent on the UBL, U-Boot etc. used. This
patch tries to minimize that dependency by setting first partition for UBL,
U-Boot and environment altogether.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

There have accumulated quite a lot of them after the code reorganizations...

In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch makes it easier to identify SoC init failures
by panicing when SoC init fails. Without successful SoC
init, the kernel eventually fails when attempt is made to
access the clocks.

Also, an error is printed when JTAG ID match fails to make
it easier to identify failures due to SoC rev changes.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.

This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

DA850/OMAP-L138 EVM can be connected to an UI card which has various
peripherals on it.The UI card has TCA6416 expander which can be probed
to check whether the UI card is connected or not. If the UI card is
connected, setup NOR and NAND devices. This is done via the expander
setup callback.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Replace badly chosen 'psc_ctlr' name of the 'struct clk' field (PSC already
means "Power and Sleep Controller", so the '_ctlr' postfix makes the name
tautological) with technically correct 'gpsc' (Global PSC -- which contains
all the module registers).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch adds support for using the TPS65070 PMIC found
on the DA850/OMAP-L138 EVM.

It defines the power rail consumer mapping and registers the
the I2C based PMIC as a board device.

The power rail constraints are derived from the maxmimum and
minimum recommended operating condition values of the respective
consumers derived from section 5.2 of the OMAP-L138 datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch adds support for regulating the CVDD voltage for the
DA850/OMAP-L138 platform.

The CVDD min and max values for each OPP have been obtained from
section 5.2 "Recommended Operating Conditions" of SPRS586
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Adds basic frequency scaling support for DA850/OMAP-L138.

Currently, frequency scaling only on PLL0 is supported. No scaling of PLL1
as yet.

Peripherals like MMC/SD which have a clock input synchronous with
ARM clock will not work well since the clock will change behind their backs.
Support for notification to such devices to adjust themselves to the
new frequency will be added in later patches. Current defconfigs keep
CPUFreq disabled so it will not affect normal operation.

The OPP defintions assume clock input of 24MHz to the SoC. This is inline
with hardcoding of input frequency in the <soc>.c files. At some point
this will need to move into board dependent code as new boards appear with
a different reference clock.

Tested on OMAP-L138 EVM with ondemand governer and a shell script to
vary processor load.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Adds a basic CPUFreq driver for DaVinci devices registering with the
kernel CPUFreq infrastructure.

Support is added for both frequency and voltage regulation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

All that is needed is the existing #include <linux/gpio.h>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Newer revs of da830 silicon have different 'variant' field of the JTAG
id register.  Current code only supports rev 1.0 silicon.

This patch adds support for rev1.1 and rev2.0 silicon and updates
the 'name' strings to add a '-' between 'omap' & 'l137' to have
consistent naming with da850/omap-l138.

From Mark Grosen <mgrosen@ti.com>:

"There are currently three silicon revisions for OMAPL137. The JTAG IDs
 (DEVIDR register contents) for each silicon revision are shown below:

 0x0B7D F02F for silicon revision 1.0
 0x8B7D F02F for silicon revision 1.1
 0x9B7D F02F for silicon revision 2.0

 Corresponding errata documentation will be available in the next few
 weeks on the ti.com website."
Reported-by: Nick Thompson <Nick.Thompson@gefanuc.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>