A regulatory rule is invalid when the frequency difference
between the end of the frequency range and the start is 0.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This introduces a debugfs file (ieee80211/phy#/hwsim/ps) that can be
used to force a simulated radio into power save mode. Following values
can be written into this file to change PS mode:
0 = power save disabled (constantly awake)
1 = power save enabled (drop all frames; do not send PS-Poll)
2 = power save enabled (send PS-Poll frames automatically to receive
    buffered unicast frames); not yet fully implemented
3 = manual PS-Poll trigger (send a single PS-Poll frame)

Two different behavior for power save mode processing can be tested:
- move between modes 1 and 0 (i.e., receive all buffered frames at a
  time)
- move to mode 1 and use manual PS-Poll frames (write 3 to the 'ps'
  debugfs file) to fetch power save buffered frames one at a time

Mode 2 (automatic PS-Poll) does not yet parse Beacon frames, but
eventually, it should take a look at TIM IE and send PS-Poll if a
traffic bit is set for our AID.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the addition of basic rate set and TX queue parameter
configuration and confirmation that power save buffering is
working again, mac80211 is now in state that allows AP mode to be
used without major problems. Consequently, it is time to allow this
mode to be enabled without having to patch the kernel.

AP mode requires hostapd for management frame processing and as such,
configuring this mode is only allowed through cfg80211 (not with
iwconfig and WEXT).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In previous code all the rates were marked as basic.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was possible to trigger a kernel panic because beacon_timer may not
have been deleted in all cases when the kernel module was removed while
hostapd was still running.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Provide detailed information on TX queue parameter changes to make it
easier to debug mac80211 functionality.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Provide detailed information on BSS configuration changes to make it
easier to debug mac80211 functionality.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new mechanism for allocing space for control frames,
didn't "zero" out the payload data... However I haven't
heard of any hiccups so far...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fix rate scaling initialization. Rate scaling
was initialized always with B antenna.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch change the name of the double inclusion protection in
iwl-commands.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch renames functions that are generic in iwl-agn and had a iwl4965
prefix.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 supports multiple virtual interfaces for a single device. For
example, a managed interface (wlan0) and a monitor interface (mon0) can
exist at the same time. Thus priv->iw_mode is not sufficient to track
the wireless mode any more. The patch redefines priv->iw_mode as the
first interface mode (the same as priv->vif->type if priv->vif != NULL).
If another monitor type interface is created later, we don't change
priv->iw_mode into monitor. This way, the original interface still
works. The patch also requests mac80211 to do reassociation after we
change the Rx filter flags.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes 4965 prefix from comments and one function
in iwl-agn-rs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a helper function that, given a bitmap of basic
rates and a bitrate returns the response rate for this rate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath9k/xmit.c: In function ‘ath_tx_start’:
drivers/net/wireless/ath9k/xmit.c:1858: warning: ‘tid’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a 10 msec
delay after the call to set a new channel, but not before.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Each of the primary write routines, rtl8187_write_phy(),
rtl8225_write_bitbang(), and rtl8225_write_8051() all conclude with an
msleep() command. Testing shows that these are not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Routine rtl8225_write() calls either rtl8225_write_bitbang() or
rtl8225_write_8051(), both of which end with an msleep() command. As a
result, a rtl8225_write() immediately followed by an msleep() is not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Routine rtl8225_write_phy_cck() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_cck()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Routine rtl8225_write_phy_ofdm() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_ofdm()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rtl8187 driver contains 3 sleep statements that are longer than
a second. Testing has shown no bad effects when they are removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All operating modes which require beaconing should
depend on the availability of beacon entries from
the hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can safely remove ieee80211_bss_conf from rt2x00_intf,
it is provided by mac80211 in ieee80211_vif as well.
(rt2x00_intf is the drv_priv field of ieee80211_vif).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.

 * Remove set_retry_limit callback function, handled
   through config()
 * Move config_antenna to its own callback function,
   it isn't handled by mac80211 anymore
 * Use IEEE80211_CONF_CHANGED_* flags and remove manual
   checks
 * Removed deprecated short slot setting through config()
   and put it in config_erp() through which mac80211 now
   configures it
 * Remove config_phymode() and move contents to config_erp()
   since it only managed the basic rates which is now
   determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP
in hardware.  The open-sourced Atheros HAL has code for accessing this
portion so now we know how where to put the key material.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This change re-enables hardware encryption for ath5k after setting up
mac80211 to handle the initialization vectors which happens to make it
work.  Add a module param (nohwcrypt) to optionally turn it off.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes two current compilation problems. They showed up
with CONFIG_IEEE80211_DEBUG defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 has RX A-MPDU reordering support.
Use that and remove redundant RX processing within the driver.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Doing an interface down/up leaves the old HT assoc
information, clear it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>