Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3c589_cs,3c574_cs,serial_cs:

 (1)add cis(firmware) of 3Com lan&modem mulitifunction pcmcia card.
 (2)load correct configuration register for 3Com card
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net.h uses the macro ETH_ALEN which is defined in linux/if_ether.h.
Discovered when hacking on virtio-over-pci patches.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds new logic to support a clock gating feature found on the
latest set of chipsets. The clock gating is performed on the tx/rx
engines when the link is disconnected. Clock gating helps in reducing
power consumption.

* modified based on comments from netdev
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller.  Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.

This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver.  This id is the same in both new devices.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs.  This means that if LEDs are fitted they
won't ever light.

This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When netconsole is loaded and a network interface fades away (e.g. on
rmmod $interface_driver_module) the rmmod remains stuck and some locks
are taken that prevent any additional module loading/unloading as well
as interface up/down changes.
In addition kernel logs (and console) get flooded at 10s interval with

[  122.464065] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
[  132.704059] unregister_netdevice: waiting for eth0 to become free. Usage count = 1

This patch lets netconsole take NETDEV_UNREGISTER event into account
and release the affected interface if it was in use.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.

Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lennert Buytenhek wrote:
> Since 4fb66994 ("net: Optimize memory
> usage when splicing from sockets.") I'm seeing this oops (e.g. in
> 2.6.30-rc3) when splicing from a TCP socket to /dev/null on a driver
> (mv643xx_eth) that uses LRO in the skb mode (lro_receive_skb) rather
> than the frag mode:

My patch incorrectly assumed skb->sk was always valid, but for
"frag_listed" skbs we can only use skb->sk of their parent.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Debugged-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	Documentation/isdn/00-INDEX
	drivers/net/wireless/iwlwifi/iwl-scan.c
	drivers/net/wireless/rndis_wlan.c
	net/mac80211/main.c

This reverts commit 01198304.

Causes warnings in the build as reported by Stephen Rothwell.
So this change is worse than what it's curing.
Signed-off-by: David S. Miller <davem@davemloft.net>

Ignore link partner advertising flags while AN is not complete.

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mdio_support and lp_advertising fields to ethtool_cmd.  Set these
in mdio45_ethtool_gset{,_npage}().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This implements the ETHTOOL_SPAUSEPARAM operation for MDIO (clause 45)
PHYs with auto-negotiation MMDs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.

Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IEEE 802.3 clause 45 specifies the MDIO interface and registers for
use in 10G and other PHYs, similar to the MII management interface.

PHYs may have up to 32 MMDs corresponding to different sub-layers and
functions, each with up to 65536 registers.  These are addressed by
PRTAD (similar to the MII PHY address) and DEVAD.  Define a mapping
for specifying PRTAD and DEVAD through the existing MII ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a PORT_OTHER to represent all other physical port types.  Current
NICs generally do not allow switching between multiple port types in
software so specific types should not be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value.  This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.

Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.

This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill.  This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.

While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

These two memory barriers in performance-critical paths are not needed
on x86.  Even if some other architecture does buffer PCI I/O space
writes, the existing memory-mapped I/O barriers are unlikely to be what
is needed.
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>