Fix gcc warning: ipw2100.c:2460: ISO C90 forbids mixed declarations and code
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Andrea Merello <andreamrl at tiscali it>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a big array overun found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a problem in the ieee80211 probe response and beacon
reception code that would use the packet statistics for a network even
if they were received on a channel other than that which the network
exists on.

This causes a problem in overlapping channels where, for example, a
strong AP on channel 2 could have its beacons received on channels 1 and
3, but at much lower signal levels.  If scanning was done sequentially,
this means the beacon received on channel 3 would update the AP's signal
level as being much lower than it really is, which subsequently could
cause that AP to be passed over and an alternate AP selected.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch modifies the driver to support the ipw2200-fw-3.0 image format.

The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:

1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)

2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.

Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:

        http://ipw2200.sf.net/firmware.phpSigned-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: Olivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set a meaningful silence threshold value (replacing our previous "0"
default), which gets rid of the gratuitous "Link deterioration"
notifications that we've been receiving from firmware.  This
notification feature tells the driver information to help it determine
when to pre-emptively restart the firmware/ucode in anticipation of
firmware errors!  But since setting this new threshold, I haven't seen
any such notifications.  At least it keeps the logs a little less busy.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.

if (priv->ieee->wpa_enabled &&
	network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Only on CONFIG_IPW2200_DEBUG is not defined
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.

So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...

To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb.  This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.

I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix QoS is not active even the network and the card is QOS enabled.
The problem is we pass the wrong ieee80211_network address to
ipw_handle_beacon/ipw_handle_probe_response, thus the
ieee80211_network->qos_data.active will not be set, causing the driver
not sending QoS frames at all.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the correct STYPE for Qos data.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Coverity checker spotted the following bug in dup_namespace():

<--  snip  -->

        if (!new_ns->root) {
                up_write(&namespace_sem);
                kfree(new_ns);
                goto out;
        }
...
out:
        return new_ns;

<--  snip  -->

Callers expect a non-NULL result to not be freed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It seems that setting scheduling policy and priorities is also the kind of
thing that might be performed in apps that also use the NUMA API, so it
would seem consistent to use CAP_SYS_NICE for NUMA also.

So use CAP_SYS_NICE for controlling migration permissions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Update the documentation for page migration.

- Fix up bits and pieces in cpusets.txt

- Rework text in vm/page-migration to be clearer and reflect the final
  version of page migration in 2.6.16. Mention Andi Kleen's numactl
  package that contains user space tools for page migration via
  libnuma. Add reference to numa_maps and to the manpage in numactl.

- Add todo list for outstanding issues
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

page migration currently simply retries a couple of times if try_to_unmap()
fails without inspecting the return code.

However, SWAP_FAIL indicates that the page is in a vma that has the
VM_LOCKED flag set (if ignore_refs ==1).  We can check for that return code
and avoid retrying the migration.

migrate_page_remove_references() now needs to return a reason why the
failure occured.  So switch migrate_page_remove_references to use -Exx
style error messages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It seems this patch got dropped (it was in addition to the `s390:
improve response code handling in chsc_enable_facility()' patch).
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* git://oss.sgi.com:8090/oss/git/rc-fixes:
  Fix a direct I/O locking issue revealed by the new mutex code.

Affects only XFS (i.e. DIO_OWN_LOCKING case) - currently it is
not possible to get i_mutex locking correct when using DIO_OWN
direct I/O locking in a filesystem due to indeterminism in the
possible return code/lock/unlock combinations.  This can cause
a direct read to attempt a double i_mutex unlock inside XFS.

We're now ensuring __blockdev_direct_IO always exits with the
inode i_mutex (still) held for a direct reader.

Tested with the three different locking modes (via direct block
device access, ext3 and XFS) - both reading and writing; cannot
find any regressions resulting from this change, and it clearly
fixes the mutex_unlock warning originally reported here:
http://marc.theaimsgroup.com/?l=linux-kernel&m=114189068126253&w=2Signed-off-by: Nathan Scott <nathans@sgi.com>
Acked-by: Christoph Hellwig <hch@lst.de>

This fixes a race where lsn could be cleared before taking the lock
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] zfcp: fix device registration issues
  [SCSI] scsi_transport_fc: fix FC_HOST_NUM_ATTRS
  [SCSI] scsi: aha152x pcmcia driver needs spi transport
  [SCSI] zfcp: correctly set this_id for hosts
  [SCSI] Add Brownie to blacklist

lapic_shutdown() re-enables interrupts which is un-desirable for panic
case, so use local_irq_save() and local_irq_restore() to keep the irqs
disabled for kexec on panic case, and close a possible race window while
kdump shutdown as shown in this stack trace

   -- BUG: spinlock lockup on CPU#1, bash/4396, c52781a0
   [<c01c1870>] _raw_spin_lock+0xb7/0xd2
   [<c029e148>] _spin_lock+0x6/0x8
   [<c011b33f>] scheduler_tick+0xe7/0x328
   [<c0128a7c>] update_process_times+0x51/0x5d
   [<c0114592>] smp_apic_timer_interrupt+0x4f/0x58
   [<c01141ff>] lapic_shutdown+0x76/0x7e
   [<c0104d7c>] apic_timer_interrupt+0x1c/0x30
   [<c01141ff>] lapic_shutdown+0x76/0x7e
   [<c0116659>] machine_crash_shutdown+0x83/0xaa
   [<c013cc36>] crash_kexec+0xc1/0xe3
   [<c029e148>] _spin_lock+0x6/0x8
   [<c013cc22>] crash_kexec+0xad/0xe3
   [<c0215280>] __handle_sysrq+0x84/0xfd
   [<c018d937>] write_sysrq_trigger+0x2c/0x35
   [<c015e47b>] vfs_write+0xa2/0x13b
   [<c015ea73>] sys_write+0x3b/0x64
   [<c0103c69>] syscall_call+0x7/0xb
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This reverts commit c33d4568.

Andrew Clayton and Hugh Dickins report that it's broken for them and
causes strange page table and slab corruption, and spontaneous reboots.

Let's get it right next time.

Cc: Andrew Clayton <andrew@rootshell.co.uk>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Disable the EDAC sysfs code.  The sysfs interface that EDAC presents to
  user space needs more thought, and is likely to change substantially.
  Therefore disable it for now so users don't start depending on it in its
  current form.

- Disable the default behavior of calling panic() when an uncorrectible
  error is detected (since for now, there is no sysfs interface that allows
  the user to configure this behavior).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In theory, NLM specs assure us that the server will only reply LCK_GRANTED or
LCK_DENIED_GRACE_PERIOD to our NLM_UNLOCK request.

In practice, we should not assume this to be the case, and the code will
currently Oops if we do.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In rpc_wake_up() and rpc_wake_up_status(), it is possible for the call to
__rpc_wake_up_task() to fail if another thread happens to be calling
rpc_wake_up_task() on the same rpc_task.

Problem noticed by Bruno Faccini.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>