* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
  ACPI: Delete the IRQ operation in throttling controll via PTC

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: cpu accounting controller (V2)

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] NCR5380: Fix bugs and canonicalize irq handler usage
  [SCSI] zfcp: fix cleanup of dismissed error recovery actions
  [SCSI] zfcp: fix dismissal of error recovery actions
  [SCSI] qla1280: convert to use the data buffer accessors
  [SCSI] iscsi: return data transfer residual for data-out commands
  [SCSI] iscsi_tcp: fix potential lockup with write commands
  [SCSI] aacraid: fix security weakness
  [SCSI] aacraid: fix up le32 issues in BlinkLED
  [SCSI] aacraid: fix potential panic in thread stop
  [SCSI] aacraid: don't assign cpu_to_le32(constant) to u8

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
  [INET]: Fix inet_diag dead-lock regression
  [NETNS]: Fix /proc/net breakage
  [TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
  [NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
  [NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
  [DECNET]: dn_nl_deladdr() almost always returns no error
  [IPV6]: Restore IPv6 when MTU is big enough
  [RXRPC]: Add missing select on CRYPTO
  mac80211: rate limit wep decrypt failed messages
  rfkill: fix double-mutex-locking
  mac80211: drop unencrypted frames if encryption is expected
  mac80211: Fix behavior of ieee80211_open and ieee80211_close
  ieee80211: fix unaligned access in ieee80211_copy_snap
  mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
  SCTP: Fix build issues with SCTP AUTH.
  SCTP: Fix chunk acceptance when no authenticated chunks were listed.
  SCTP: Fix the supported extensions paramter
  SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
  SCTP: Fix the number of HB transmissions.
  [TCP] illinois: Incorrect beta usage
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
  LIB82596: correct data types for hardware addresses
  via-velocity: don't oops on MTU change (resend)
  Stop phy code from returning success to unknown ioctls.
  SET_NETDEV_DEV() in fec_mpc52xx.c
  net: smc911x: only enable for mpr2 on sh.
  e1000: Fix NAPI state bug when Rx complete
  sky2: turn of dynamic Tx watermark workaround (FE+ only)
  sky2: don't use AER routines
  sky2: revert to access PCI config via device space
  cxgb - fix stats
  cxgb - fix NAPI
  cxgb - fix T2 GSO
  ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
  phylib: marvell: add support for TX-only and RX-only Internal Delay
  phylib: add PHY interface modes for internal delay for tx and rx only
  skge: MTU changing fix
  skge: serial mode register values
  skge version 1.13
  skge: increase TX threshold for Jumbo
  skge: fiber link up/down fix
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_mv: Fix broken Marvell 7042 support.
  libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
  ata_piix: add more toshiba laptops to broken suspend list
  libata: More IVB horkage from TSST
  libata: report protocol and full CDB on error
  Several fixes for the AVR32 PATA driver
  sata_mv: fix compilation error when enabling DEBUG
  Set proper ATA UDMA mode for bf548 according to system clock.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Under the conditions that UML uses it, tcgetattr is guaranteed to return
-EINTR when the console is attached to /dev/ptmx, making generic_console_write
hang because it loops, calling tcgetattr until it succeeds.  This is a host
bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the
details.

This patch works around it by blocking SIGIO while the terminal attributes are
being fiddled.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I forgot to have an int-returning function actually return something.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The previous commit ("uml: keep UML Kconfig in sync with x86") is not
enough, unfortunately.  If we go that way, we need to add dependencies
on !UML for several options.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a UML build breakage introduced by commit
1032c0ba - it introduces X86_32, with many
things which UML needs depending on it.

This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to
the UML/i386 Kconfig.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix possible memory overrun issue in the isdn ioctl code.

Found by ADLAB <adlab@venustech.com.cn>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: ADLAB <adlab@venustech.com.cn>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.

This patch fixes it by introducing a separate mutex to protect the
handling of handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Changed resolution of named references in packages

Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.

http://bugzilla.kernel.org/show_bug.cgi?id=5328
http://bugzilla.kernel.org/show_bug.cgi?id=9429Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Commit cfb52856 removed a useful feature for
us, which provided a cpu accounting resource controller.  This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.

The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df64), with
these differences:

        - Removed load average information. I felt it needs more thought (esp
	  to deal with SMP and virtualized platforms) and can be added for
	  2.6.25 after more discussions.
        - Convert group cpu usage to be nanosecond accurate (as rest of the cfs
	  stats are) and invoke cpuacct_charge() from the respective scheduler
	  classes
	- Make accounting scalable on SMP systems by splitting the usage
	  counter to be per-cpu
	- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
	  code is not big enough to warrant a new file and also this rightly
	  needs to live inside the scheduler. Also things like accessing
	  rq->lock while reading cpu usage becomes easier if the code lived in
	  kernel/sched.c)

The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>

 Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
 some simple tests like cpuspin (spin on the cpu), ran several tasks in
 the same group and timed them. Compared their time stamps with
 cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.

This fixes an oops on T61 -- a regression due to
f79f06ab b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

sata_mv:  Fix broken Marvell 7042 support.

The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus.  Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.

This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.

Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.

This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.

Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.

Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:

> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.

Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add more toshiba laptops to broken suspend list.  This is from OSDL
bugzilla bug 7780.

tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.

signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands.  Report them on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Several fixes for the AVR32 PATA driver:

* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.

* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.

* Removed .port_disable and .irq_ack as these are no longer needed.

* Improved some comments.
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

use sstatus instead status.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

UDMA Mode - Frequency compatibility

UDMA5 - 100 MB/s   - SCLK  = 133 MHz
UDMA4 - 66 MB/s    - SCLK >=  80 MHz
UDMA3 - 44.4 MB/s  - SCLK >=  50 MHz
UDMA2 - 33 MB/s    - SCLK >=  40 MHz
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized.  This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This kind of sucks, and prevents the Fedora installer from using the
device for network installs...

[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

eth0        ESSID:off/any  Nickname:""
          NWID:0  Channel:0  Access Point: 00:00:BF:81:14:E0
          Bit Rate:-1.08206e+06 kb/s   Sensitivity=0/0
          RTS thr:off   Fragment thr:off
          Encryption key:<too big>
          Power Management:off
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This helps to allow the Fedora installer to use the built-in Ethernet on
the Efika for a network install.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The smc911x.h is a bit of a mess, not supporting any sort of generic
configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have
suitable definitions, so we reflect this in the Kconfig also.

While there are other SH boards that will likely turn this on in the
2.6.25 time frame, it's not worth trying to stub around at the moment.

Fixes up the allmodconfig build, as noted by akpm.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.

This reverts 555382cbSigned-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.

Reverts: 167f53d0

Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix MAC stats accounting.
Fix get_stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

netif_rx_complete() should be called only
when work_done < budget.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Previously, Internal Delay specification implied the delay be
applied to both TX and RX.  This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>