Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.

However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins.  The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c.  Thus, there
are two possible volumes.

When only one of them is used, we can name it as "Master".  OTOH, when
both are used at the same time, they have to be named uniquely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of fixed "Front" mixer name, try to assign a better name, e.g.
"Master" or "Speaker" fot the primary output volume controls of ALC260
codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When there is only one DAC is used for ALC880, try to assign a better
name, either Speaker or Front, depending on the output pin type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Provide a standard parser for input pins to create the input mixer
and input source controls instead of having a difference one for each
Realtek codec.  The new helper parses the codec connections dynamically
isntead of fixed indicies.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Reuse a part of the code of ALC268 parser for ALC269.
This will change the default output volume either to Front or Speaker
depending on the pin configuration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The BIOS pin configs are in fact correct and shall not be overwritten.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.

The codec differences before/after patch are:

@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
   Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
     Conn = Digital, Color = White
     DefAssociation = 0x3, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x24: IN
+  Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
   Pin Default 0x41813021: [N/A] Line In at Ext Rear
     Conn = 1/8, Color = Blue
     DefAssociation = 0x2, Sequence = 0x1
-  Pin-ctls: 0x24: IN VREF_80
+  Pin-ctls: 0x40: OUT VREF_HIZ
   Unsolicited: tag=00, enabled=0
   Connection: 1
      0x24

Tests show that it won't impact (external) Mic recording.
Reported-by: "Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The auto-mic clean-up patches caused regressions on some ALC268 models
that have no proper input_mux but with "Input Source" mixer elements.
Such a combination results in Oops when accessed.

[A reason why set_capture_mixer() isn't used in patch_alc268() is that
ALC268 codec have HDA_OUTPUT direction for capture volumes unlike other
codecs.  Thus it needs own definitions of capture elements.]

This patch fixes the issues:
- Add a capture mixer definition without input-source
- Use the new capture mixer appropriately
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The previous fix removed the definition of num_adc_nids wrongly, and
this resulted in the missing input-source control.  Now readded again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A few improvements for IDT 92HD83xxx codec pareser:
- Remove unused / deprecated mixer-amp controls
- Handle d-mics as normal inputs since this codec has no separate
  MUXes for analog and digital
- Don't create duplicated controls for capture volumes with Mux
  capture volumes
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Enable line-out detection for IDT/STAC codecs only when speaker pins
exist.  In some cases, the speaker itself is identified as line-out,
and this confuses the situation.  Only the extra line-outs should do
auto-muting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

With auto config model of alc268 realtek codec, it allows to select any
of possible available digital microphone inputs when only one is
available. For example, when only digital mic in nid 0x12 is available,
on second input source it will allow you to select unavailable digital
mic in nid 0x13. The problem is that selecting unavailable digital mic
creates a source of noise when recording (I'm not sure if this happens
on all machines with alc268 and only one digital mic input, but testing
on a quanta uw1 netbook a lot of noise is introduced in recording from
digital mic 0x12/first input source, when you select the unavailable
digital mic 0x13 for capture source 0x24 in the second input source in
mixer).

Then to avoid noise when recording from digital mic with auto model in
this case, prevent a digital mic input source to be selected if
microphone is not available.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Move static codes to setup from init_hook for each model.

Also, use the common auto-mic selection helper for devices that support
auto-mic selection.  They just need to set up ext_mic, int_mic and
auto_mic flag in the setup section.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added setup hook to ALC preset struct to be called at in the parser
but not at each init callback.
This can be used for setting up the static pins, etc, while the
init hook should be used for updating the status again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Created a white-list to enable MSI since some devices require MSI
explicitly due to BIOS/ACPI problems.  Simply using a quirk list.
As the first case, take HP Compaq CQ40.

Reference: Novell bnc#529971
	https://bugzilla.novell.com/show_bug.cgi?id=529971Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some Realtek codecs don't provide the full connections for certain pins
from each ADC; e.g. ACL662/ALC272 gives only one of two digital-mic pins
for each ADC.  Thus, depending on the digital mic pin, the ADC/MUX to be
used has to be chosen properly.

This patch adds the check of the connectivity of pins at auto-mic mode.
If no proper connectivity is found, auto_mic flag is turned off to be
sure.

Also the mux_idx is determined during this check so it won't be checked
in the unsol event any more.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition.  This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).

This patch avoids the overriding by adding the proper checks.

Reference: Novell bnc#529467
	https://bugzilla.novell.com/show_bug.cgi?id=529467Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the auto-mic feature is enabled, we should support only one
capture stream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the support for automatic mic selection via plugging for
Realtek codecs (in auto-probing mode).  The auto-mic mode is enabled
only when one internal mic and one external mic are present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.

Reference: Novell bnc#527361
	https://bugzilla.novell.com/show_bug.cgi?id=527361Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

The previous auto-mic patch for STAC/IDT codecs causes the Oops on
machines without digital mic pins.  This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The new HP laptops have PCI SSID 103c:701x and requires model=hp-dv5.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the line-out jack is plugged/unplugged, the driver needs to check
the headphone plug, not only the line-out jack itself.  Otherwise the
headphone or the speaker may be wrongly muted/unmuted.

As a result, both STAC_HP_EVENT and STAC_LO_EVENT need to call the
same function, stac92xx_hp_detect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit fefd67f3
    ALSA: hda - Add line-out jack detection on IDT/STAC codecs
enabled wrong pins for jack detections.  Fixed to the correct ones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The new IbexPeak HDMI codec has 3 pin nodes and 2 converter nodes.
Here we assume only the first ones will be used.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit 24918b61 statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.

The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

To help disclose hardware bugs.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This converts the last CORBWP access outside of reg_lock.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just for safety.  azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.

So cmd_mutex would be a safe addition to probe_codec().
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>