Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c.  Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory."  Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Rename arch/arm/mach-omap2/memory.c to arch/arm/mach-omap2/sdrc2xxx.c, since
it contains exclusively SDRAM-related functions.  Most of the functions
are also OMAP2xxx-specific - those which are common will be separated out
in a following patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Move the contents of the arch/arm/mach-omap2/memory.h file to the
existing include/asm-arm/arch-omap/sdrc.h file, and remove memory.h.
Modify files which include memory.h to include asm/arch/sdrc.h instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix sparse issues with smartreflex.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This cleans up remaining sparse warnings for OMAP2 builds and fixes a
few CodingStyle issues.  This involves:

- removing casts where they don't belong,

- adding casts where they should be,

- marking internal functions as static,

- fixing some indentation in board-2430sdp-flash.c.

Patch should cause no change in kernel behavior.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mark casts between integers and pointers with __force to keep sparse
from complaining.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix the following sparse warnings:

arch/arm/mach-omap2/pm.c:58:6: warning: symbol 'omap2_block_sleep' was not declared. Should it be static?
arch/arm/mach-omap2/pm.c:63:6: warning: symbol 'omap2_allow_sleep' was not declared. Should it be static?
arch/arm/mach-omap2/pm.c:71:12: warning: symbol 'omap_pm_init' was not declared. Should it be static?

arch/arm/mach-omap2/pm34xx.c:49:6: warning: symbol '_omap_sram_idle' was not declared. Should it be static?

arch/arm/mach-omap2/prcm.c:96:5: warning: symbol 'cm_read_mod_reg' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:103:6: warning: symbol 'cm_write_mod_reg' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:110:5: warning: symbol 'cm_rmw_mod_reg_bits' was not declared. Should it be static?
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I2C2 at BeagleBoard is connected to expansion connector, i.e. unused if
nothing is connected to this connector. As internal OMAP3 pull up resistors
are not strong enough, enabled but unused I2C2 bus results in error messages
(e.g. I2C timeouts). I2C2 should be enabled only if something is connected to
I2C2 at board's expansion connector and this extension has additional pull up
resistors for I2C2 bus.

- Add configuration option for this
- Use configuration option in board-omap3beagle
- While being there, add OMAP3 to OMAP I2C help text
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Only once MODULE_ALIAS declaration is enough.
Columns are counted from 0 to n_cols - 1.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable nand and jffs2 in defconfig
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Koen Kooi <koen at openembedded dot org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add nand support to omap3beagle
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Koen Kooi <koen at openembedded dot org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Dirk Behme <dirk.behme@gmail.com>

Extend omap2 mtd nand driver to work with ARCH_OMAP3 boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Koen Kooi <koen at openembedded dot org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch removes a few errors and warnings reported by checkpatch.pl.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch moves menelaus register map to include/linux/i2c/menelaus.h
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch moves menelaus header from include/asm-arm/arch-omap/
to include/linux/i2c/

It also includes menelaus' headers to include/linux/i2c
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch makes drivers/i2c/chips/menelaus.c file to use macros
instead of some constant magic numbers.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Several functions use old-style function documentation; convert those to
use the current kerneldoc style.

Thanks to Felipe Balbi <felipe.balbi@nokia.com> for catching an error.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Koen Kooi <koen@openembedded.org>

Update and fix Beagle LED declarations:  gpios for USR0 and USR1
were swapped, and their names don't match docs or silksreen.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

n800 and n810 have different peripherals on the second i2c bus
(tea5761 on n800 and lm8323 on n810). Split the i2c_board_info to
common and hw specific to avoid probing nonexistent devices.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

req is an automatic variable and thus we cannot rely on it being initialized to
zero (I am leaving the 0!= NULL discussion aside). Other functions test
if this pointer is NULL, in order to determine whether it is a valid address or
not.
Signed-off-by: Viktor Rosendahl <viktor.rosendahl@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the omap2 nand driver code that allows
reading of partition data from board info.

The parse_mtd_partitions() function no longer returns a
negative error in case cmdline is not passed.
See commit: b0d06afbSigned-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mask/clear TWL module IMRs/ISRs by iterating through arrays rather than
using a block of cut-and-pasted commands.  Removes 1056 bytes of bloat.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_init_irq() uses a bunch of magic numbers as register indices; this
has already led to several errors, fixed earlier in this patch series.
Now use descriptive macros instead of magic numbers.  This patch should
not change kernel behavior.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_init_irq() uses "magic numbers" to access TWL module IMR and ISR
registers.  Symbolic constants are definitely preferred.

Rather than duplicating already existing symbolic constants in
twl4030-gpio.c and twl4030-pwrirq.c, move the existing constants out
into include files.  This patch should not change kernel behavior.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_init_irq() prints error messages and returns if any interrupt mask
register writes fail.  Change this to generate a warning traceback and
to continue execution rather than skipping TWL init.  (These mask
writes should not fail at all unless either the I2C bus or the TWL4030
is somehow wedged.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

TWL4030 interrupt status register bits can be cleared in one of two ways:
either by reading from the register, or by writing a 1 to the
appropriate bit(s) in the register.  This behavior can be altered at any
time by the <twlmodule>_SIH_CTRL.COR register bit ("clear-on-read").

The TWL4030 TRM is deeply confused as to whether COR=1 means that the
registers are cleared on reads, or cleared on writes.  Peter De
Schrijver <peter.de-schrijver> confirms that COR=1 means that the registers
are cleared on read.

So, for each TWL4030 SIH, check the value of the *_SIH_CTRL.COR bit, and if
it is 1, use reads to clear the ISRs; if it is 0, use writes.

Also, use WARN_ON() to warn if the read/write failed, and don't skip
the rest of the initialization on failure either.

Thanks to Peter for his help with this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_init_irq() does not clear MADC interrupt status registers upon init -
fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The existing code to mask and clear BCI interrupts in twl_init_irq() is
wrong.  It uses the wrong register offsets, it does not mask all of the
BCI IMR registers, and it does not clear all of the BCI ISR registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_init_irq() does not clear the TWL GPIO ISR registers, but the PIH
ISR thinks that it has.  This causes any previously-latched GPIO interrupts
to be stuck on until twl4030-gpio.c initializes, often drowning the console in

    TWL4030 module irq 368 is disabled but can't be masked!

messages.  This seems to be a particular problem when booting on Beagle.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

twl_irq_init() clears PWR interrupt status bits, then masks the interrupts
off, then clears the PWR interrupt status bits again.  The first clear
seems unnecessary, so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Skip compiling OMAP15xx I2C ISR for non-OMAP15xx builds.  Saves 400 bytes
of text for most OMAP builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mark functions called only at init time as __init.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap_i2c_idle() sets an internal flag, "dev->idle", instructing its
ISR to decline interrupts.  It sets this flag before it actually masks
the interrupts on the I2C controller.  This is problematic, since an
I2C interrupt could arrive after dev->idle is set, but before the
interrupt source is masked.  When this happens, Linux disables the I2C
controller's IRQ, causing all future transactions on the bus to fail.

Symptoms, happening on about 7% of boots:

   irq 56: nobody cared (try booting with the "irqpoll" option)
   <warning traceback here>
   Disabling IRQ #56
   i2c_omap i2c_omap.1: controller timed out

In omap_i2c_idle(), this patch sets dev->idle only after the interrupt
mask write to the I2C controller has left the ARM write buffer.
That's probably the major offender.  For additional prophylaxis, in
omap_i2c_unidle(), the patch clears the dev->idle flag before
interrupts are enabled, rather than afterwards.

The patch has survived twenty-two reboots on the 3430SDP here without
wedging I2C1.  Not absolutely dispositive, but promising!
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Latest musb_hdrc code wouldn't:
  * build ... because there's now a standard WARN() macro
  * build without false printf format warnings ... "%zd" is for ssize_t,
    while "%zu" is for size_t
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

USBHOST on 3430ES2+ has both an initiator and a target CM_IDLEST bit.
Previously, usbhost_48m_fclk enable waited on the wrong bit -- now
fixed.  Also, it appears that USBHOST module readiness (in terms of
CM_IDLEST) only depends on usbhost_48m_fclk and usbhost_iclk.  So
don't wait on usbhost_120m_fck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.

One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses.  This patch sticks with the previous setting, which
seems reasonable.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes a write to the wrong address in the triton2 chip.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branches 'master' and 'linus'