This is useful for implementing get_status() in terms of get_mode().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.

Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.

Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.

Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.

Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.

An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.

The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.

Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.

This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().

As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Register ezx-pcap earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Vibrator will be accessed via the pcap-regulator driver, no need to expose its
bits in the header file.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch corrects the support for MMCSD card detection
and read only feature for SoC DM355.

EVMDM355_ECP_VA4.pdf, from Spectrum digital, suggests that
Bit 2 and 4 should be checked for card detection. However
on the EVM, bits 1 and 3 gives this status, for MMC/SD
instance 0 and 1 respectively. The pdf also suggests that
Bit 1 and 3 should be checked for write protection. However
on the EVM bits 2 and 4 gives this status.

This document can be downloaded from
http://c6000.spectrumdigital.com/evmdm355/reve/files/EVMDM355_ECP_VA4.pdfSigned-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The 10 bits definition was the 8 bits one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Current implementation is prone to races, this patch attempts to remove all
but one (in pcf50633_adc_sync_read).

The idea is that we need to guard the queue access only on inserting and
removing items. If we insert and there're no more items in the queue it
means that the last irq already happened and we need to trigger ADC
manually. If not, then the next conversion will be triggered by the irq
handler upon completion of the previous.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.

I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Make that twl4030-pwrbutton.c driver probe with current
child creation api for twl4030.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add (partial) support for the voltage regulators on the PCAP2 PMIC.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Mask interrupts before servicing them and loop while pcap asserts the interrupt
line.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The file_operations write prototype should return a ssize_t.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
  debugfs: Modify default debugfs directory for debugging pktcdvd.
  debugfs: Modified default dir of debugfs for debugging UHCI.
  debugfs: Change debugfs directory of IWMC3200
  debugfs: Change debuhgfs directory of trace-events-sample.h
  debugfs: Fix mount directory of debugfs by default in events.txt
  hpilo: add poll f_op
  hpilo: add interrupt handler
  hpilo: staging for interrupt handling
  driver core: platform_device_add_data(): use kmemdup()
  Driver core: Add support for compatibility classes
  uio: add generic driver for PCI 2.3 devices
  driver-core: move dma-coherent.c from kernel to driver/base
  mem_class: fix bug
  mem_class: use minor as index instead of searching the array
  driver model: constify attribute groups
  UIO: remove 'default n' from Kconfig
  Driver core: Add accessor for device platform data
  Driver core: move dev_get/set_drvdata to drivers/base/dd.c
  Driver core: add new device to bus's list before probing

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (641 commits)
  Staging: remove sxg driver
  Staging: remove heci driver
  Staging: remove at76_usb wireless driver.
  Staging: rspiusb: remove the driver
  Staging: meilhaus: remove the drivers
  Staging: remove me4000 driver.
  Staging: line6: ffzb returns an unsigned integer
  Staging: line6: pod.c: style cleanups
  Staging: iio: introduce missing kfree
  Staging: dream: introduce missing kfree
  Staging: comedi: addi-data: NULL dereference of amcc in v_pci_card_list_init()
  Staging: vt665x: fix built-in compiling
  Staging: rt3090: enable NATIVE_WPA_SUPPLICANT_SUPPORT option
  Staging: rt3090: port changes in WPA_MIX_PAIR_CIPHER to rt3090
  Staging: rt3090: rename device from raX to wlanX
  Staging: rt3090: remove possible conflict with rt2860
  Staging: rt2860/rt2870/rt3070/rt3090: fix compiler warning on x86_64
  Staging: rt2860: add new device ids
  Staging: rt3090: add device id 1462:891a
  Staging: asus_oled: Cleaned up checkpatch issues.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pcmcia-2.6:
  pcmcia: document return value of pcmcia_loop_config
  pcmcia: dtl1_cs: fix pcmcia_loop_config logic
  pcmcia: drop non-existant includes
  pcmcia: disable prefetch/burst for OZ6933
  pcmcia: fix incorrect argument order to list_add_tail()
  pcmcia: drivers/pcmcia/pcmcia_resource.c: Remove unnecessary semicolons
  pcmcia: Use phys_addr_t for physical addresses
  pcmcia: drivers/pcmcia: Make static

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
  PCI hotplug: clean up acpi_run_hpp()
  PCI hotplug: acpiphp: use generic pci_configure_slot()
  PCI hotplug: shpchp: use generic pci_configure_slot()
  PCI hotplug: pciehp: use generic pci_configure_slot()
  PCI hotplug: add pci_configure_slot()
  PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
  PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
  PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
  PCI: Clear saved_state after the state has been restored
  PCI PM: Return error codes from pci_pm_resume()
  PCI: use dev_printk in quirk messages
  PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
  PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
  PCI Hotplug: acpiphp: find bridges the easy way
  PCI: pcie portdrv: remove unused variable
  PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
  ACPI PM: Replace wakeup.prepared with reference counter
  PCI PM: Introduce device flag wakeup_prepared
  PCI / ACPI PM: Rework some debug messages
  PCI PM: Simplify PCI wake-up code
  ...

Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases.  The
'needs_freset' initialization added in 6e19314c ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: fix linkage problem with blk_iopoll and !CONFIG_BLOCK

* 'writeback' of git://git.kernel.dk/linux-2.6-block:
  writeback: fix possible bdi writeback refcounting problem
  writeback: Fix bdi use after free in wb_work_complete()
  writeback: improve scalability of bdi writeback work queues
  writeback: remove smp_mb(), it's not needed with list_add_tail_rcu()
  writeback: use schedule_timeout_interruptible()
  writeback: add comments to bdi_work structure
  writeback: splice dirty inode entries to default bdi on bdi_destroy()
  writeback: separate starting of sync vs opportunistic writeback
  writeback: inline allocation failure handling in bdi_alloc_queue_work()
  writeback: use RCU to protect bdi_list
  writeback: only use bdi_writeback_all() for WB_SYNC_NONE writeout
  fs: Assign bdi in super_block
  writeback: make wb_writeback() take an argument structure
  writeback: merely wakeup flusher thread if work allocation fails for WB_SYNC_NONE
  writeback: get rid of wbc->for_writepages
  fs: remove bdev->bd_inode_backing_dev_info

wb_clear_pending AFAIKS should not be called after the item has been
put on the list, except by the worker threads. It could lead to the
situation where the refcount is decremented below 0 and cause lots of
problems.

Presumably the !wb_has_dirty_io case is not a common one, so it can
be discovered when the thread wakes up to check?

Also add a comment in bdi_work_clear.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

By the time bdi_work_on_stack gets evaluated again in bdi_work_free, it
can already have been deallocated and used for something else in the
!on stack case, giving a false positive in this test and causing
corruption.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

If you're going to do an atomic RMW on each list entry, there's not much
point in all the RCU complexities of the list walking. This is only going
to help the multi-thread case I guess, but it doesn't hurt to do now.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

list_add_tail_rcu contains required barriers.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Gets rid of a manual set_current_state().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

And document its retriever, get_next_work_item().
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>