Add init support for the TUSB6010 EVM board, as connected to H4.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Tabify mux.c, no functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Additional cleanup for debug boards on H2/P2/H3/H4:  move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices).  Make H4 use that.

This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPMC updates:
 - bugfixes: wrong/missing flags, omitted write, wrong test
 - don't map memory segments starting at zero
 - improve debug messaging
 - export gpmc_get_fclk_perio]d() since it's needed to calc timings
 - expect gpmc_cs_set_timings() caller to have initialized sync vs async

Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove some conflicting declarations in omap2/memory.c so that the
file builds again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update Apollon board init to initialize NAND, USB,
and LEDs. Also configure GPMC memory for smc91x Ethernet.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Place SMS and SDRC into smart idle mode
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is an updated patch to fix lcd for H2 board. It uses platform_data
field to pass spi_device to lcd driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

H2 / H3 boards use this chip, update their board files.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

These were left out from the board file when merging these drivers,
add them here.

Call GPIO init from the board file as well, since the platform device init
code uses the GPIO API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mistral-specific:

  - Add PWL-driven LCD backlight device

  - Apply power to the board even when the LCD isn't configured; things
    like EEPROM, temperature sensor, and wakeup switch depend on it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add omap osk defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update omap h2 defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch syncs omap board specific files with linux-omap tree.

Patch consists mostly of driver updates done in linux-omap
tree for drivers not yet in mainline kernel.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.

If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmz71 specific things - board file.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed, so that disabling the SoSSI clock during idle can
be prevented.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Support the camera connector on the OSK Mistral add-on board:

  - define muxing for both camera controllers
  - mux both of them for Mistral
  - teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables some clock on omap310.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable serial idling and wakeup features
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Bugfixes for the OSK led support:

 - Fix Kconfig merge glitches:  Mistral handles idle and timer leds just fine
 - Fix pm_suspend() runtime botch:  can't sleep, so can't touch tps65010 leds

Improvements:
 - Switch sense of Mistral idle led, so idle == off

Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning.  It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix unsupported one-shot mode in set_mode hook.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fixes for the SLB shadow buffer code
  [POWERPC] Fix a compile warning in powermac/feature.c
  [POWERPC] Fix a compile warning in pci_32.c
  [POWERPC] Fix parse_drconf_memory() for 64-bit start addresses
  [POWERPC] Fix num_cpus calculation in smp_call_function_map()
  [POWERPC] ps3: Fix section mismatch in ps3/setup.c
  [POWERPC] spufs: Fix affinity after introduction of node_allowed() calls
  [POWERPC] Fix special PTE code for secondary hash bucket
  [POWERPC] Expand RPN field to 34 bits when using 64k pages

 * wrong argument passed to pci_unmap_single() on failure
   exit paths
 * leak in the same area
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.infradead.org/~dwmw2/mtd-2.6.23:
  [MTD] Makefile fix for mtdsuper

* git://git.infradead.org/battery-2.6:
  Don't compile the PMU power driver on 64-bit PowerPC

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
  sh: fix defconfigs for sh7751r boards
  sh: fix cf support on r2d boards
  sh: update r2d defconfig
  sh: update snapgear defconfig.
  sh: Fix SH-X3 FPU exception handling.
  sh: Fix pgd mismatch from cached TTB in unhandled fault.
  sh: Don't include fault-nommu on SH-2/SH-2A.
  sh: Fix irqflags tracing for SH-3/4 nommu.
  sh: Fix lockdep debugging oops on SH-3/4.

There is a couple of subtle checks which were needed to handle ptracing from
the same thread group. This was deprecated a long ago, imho this code just
complicates the understanding.

And, the "->parent->signal->flags & SIGNAL_GROUP_EXIT" check in exit_notify()
is not right. SIGNAL_GROUP_EXIT can mean exec(), not exit_group(). This means
ptracer can lose a ptraced zombie on exec(). Minor problem, but still the bug.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

the early setup function serial8250_console_early_setup() can be called
from non __init code (eg. hotpluggable serial ports like serial_cs) so
remove the __init from the call chain to avoid crashes.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>