Simple simplification...
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Make the regulator setup code simpler and more consistent:

 - The only difference between "boot_on" and "always_on" is
   that an "always_on" regulator won't be disabled.  Both will
   be active (and usecount will be 1) on return from setup.

 - Regulators not marked as "boot_on" or "always_on" won't
   be active (and usecount will be 0) on return from setup.

The exception to that simple policy is when there's a non-Linux
interface to the regulator ... e.g. if either a DSP or the CPU
running Linux can enable the regulator, and the DSP needs it to
be on, then it will be on.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch hooks up the twl4030 MMC1 regulator on Overo,
The WLAN chip connected to MMC2 on some board versions
has a dedicated regulator.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update Beagle init so it uses the new power resource hooks
to make sure that various regulators are initially off.
(Example, u-boot enables VAUX3, which isn't even wired up!!)

Also, add VPLL2 to the set of regulators used, and hook it
up to the LCD driver.  VPLL powers the digital video outputs;
for rev B boards, that's DVI only.

Drivers need to use regulator calls to enable these later.
USB and MMC handle this corrrectly (although not yet for
MMCplus cards, with 8-bit data).  The video driver doesn't.
NYET-Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Introduce support for board specific group assignments of TWL4030
power resources.  The resource type and type2 fields can also be
specified.

Most such power resources are regulators; this hook can be used
to ensure regulators that will never be used get properly disabled,
regardless of what the bootloader does.  Other resources include
control signals like CLKREQ and REGEN; this can properly couple
TWL CLKREQ (out) to OMAP SYSCLK_REQ (in) so retention mode works.

[ dbrownell@users.sourceforge.net: cosmetic and doc updates;
  use the RES_* constants in the regulator driver; fix buildbug ]
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add VPLL2 to the set of twl4030-family regulators exposed for
use by various drivers.  It's commonly used to power the digital
video outputs (e.g. LCD or DVI displays) on OMAP3 systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO IRQ enable/disable path attempts to also enable IRQ wake
support for the parent GPIO bank IRQ as well.  However, since there is
no 'set_wake' hook for the bank IRQs, these calls will always fail.
Also, since the enable will fail on the suspend path, the disable on
the resume path will trigger unbalanced enable/disable warnings.

This was discovered in the suspend/resume path on OMAP3/Beagle using
the gpio-keys driver which disables/re-enables GPIO IRQ wakeups in the
suspend/resume path.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 2ac496a2.

The commit message got lost as noted by Kevin.
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO IRQ enable/disable path attempts to also enable IRQ wake
support for the parent GPIO bank IRQ as well.  However, since there is
no 'set_wake' hook for the bank IRQs, these calls will always fail.
Also, since the enable will fail on the suspend path, the disable on
the resume path will trigger unbalanced enable/disable warnings.

This was discovered in the suspend/resume path on OMAP3/Beagle using
the gpio-keys driver which disables/re-enables GPIO IRQ wakeups in the
suspend/resume path.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200	- tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94		- gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53	- tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111	- tusb_set_sync_mode()

is -ENODEV appropriate when sysclk_ps == 0?

This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

rx51: Clean-up for checkpatch.pl
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This could be converted into more generic smc91x init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Misc clean-up for 3430-sdp to prepare for mainline
Signed-off-by: Tony Lindgren <tony@atomide.com>

The VAUX4 voltage table scrolls onto a second page in many versions
of the TWL4030 family manuals.  This doesn't mean we should ignore
those values!  Some boards use the (fully supported) 2.8V setting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branches 'master' and 'linus'

Guennadi Liakhovetski noticed that the end condition for the loop in
bitmap_find_free_region() is wrong, and the "return if error" was also
using the wrong conditional that would only trigger if the bitmap was an
exact multiple of the allocation size, which is not necessarily the case
with dma_alloc_from_coherent().

Such a failure would end up in bitmap_find_free_region() accessing
beyond the end of the bitmap.
Reported-by: Guennadi Liakhovetski <lg@denx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: remove unused -r option for module-init-tool depmod
  kbuild: fix 'make rpm' when CONFIG_LOCALVERSION_AUTO=y and using SCM tree
  kbuild: fix mkspec to cleanup RPM_BUILD_ROOT
  kbuild: fix C libary confusion in unifdef.c due to getline()

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  cpumask: mm_cpumask for accessing the struct mm_struct's cpu_vm_mask.
  cpumask: tsk_cpumask for accessing the struct task_struct's cpus_allowed.

* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
  Squashfs: Valid filesystems are flagged as bad by the corrupted fs patch

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (f75375s) Remove unnecessary and confusing initialization
  hwmon: (it87) Properly decode -128 degrees C temperature
  hwmon: (lm90) Document support for the MAX6648/6692 chips
  hwmon: (abituguru3) Fix I/O error handling

Trivial patch to fix bad links in the ext2 and ext3 documentation.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fixes-20090312' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci:
  PCIe: portdrv: call pci_disable_device during remove
  pci: Fix typo in message while disabling HT MSI mapping
  pci: don't disable too many HT MSI mapping
  powerpc/pseries: The RPA PCI hotplug driver depends on EEH
  PCIe: AER: during disable, check subordinate before walking
  PCI: Add PCI quirk to disable L0s ASPM state for 82575 and 82598

STag zero is a special STag that allows consumers to access any bus
address without registering memory.  The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system).  Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.

The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.

Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There was a report of a data corruption
http://lkml.org/lkml/2008/11/14/121.  There is a script included to
reproduce the problem.

During testing, I encountered a number of strange things with ext3, so I
tried ext2 to attempt to reduce complexity of the problem.  I found that
fsstress would quickly hang in wait_on_inode, waiting for I_LOCK to be
cleared, even though instrumentation showed that unlock_new_inode had
already been called for that inode.  This points to memory scribble, or
synchronisation problme.

i_state of I_NEW inodes is not protected by inode_lock because other
processes are not supposed to touch them until I_LOCK (and I_NEW) is
cleared.  Adding WARN_ON(inode->i_state & I_NEW) to sites where we modify
i_state revealed that generic_sync_sb_inodes is picking up new inodes from
the inode lists and passing them to __writeback_single_inode without
waiting for I_NEW.  Subsequently modifying i_state causes corruption.  In
my case it would look like this:

CPU0                            CPU1
unlock_new_inode()              __sync_single_inode()
 reg <- inode->i_state
 reg -> reg & ~(I_LOCK|I_NEW)   reg <- inode->i_state
 reg -> inode->i_state          reg -> reg | I_SYNC
                                reg -> inode->i_state

Non-atomic RMW on CPU1 overwrites CPU0 store and sets I_LOCK|I_NEW again.

Fix for this is rather than wait for I_NEW inodes, just skip over them:
inodes concurrently being created are not subject to data integrity
operations, and should not significantly contribute to dirty memory
either.

After this change, I'm unable to reproduce any of the added warnings or
hangs after ~1hour of running.  Previously, the new warnings would start
immediately and hang would happen in under 5 minutes.

I'm also testing on ext3 now, and so far no problems there either.  I
don't know whether this fixes the problem reported above, but it fixes a
real problem for me.

Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Even when page reclaim is under mem_cgroup, # of scan page is determined by
status of global LRU. Fix that.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device.  As a result, we end up with no backlight device at all.
 We should instead disable it if there is an ACPI device, as the other
laptop drivers do.  This regression was introduced in febf2d95 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").

Each laptop driver with backlight support got a similar change around
febf2d95.  The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change.  The regression is also in
2.6.28.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>		[2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register.  The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Unfortunately, Linux Foundation funding for my work on
man-pages/testing/doc under the auspices of the LF documentation
fellowship unfortunately ran out a short while ago (after earlier attempts
to seek funding, only Google stepped forward with a bit of further funding
for the position), so the patch below acknowledges something closer to
reality.

Unfortunately, there will (probably very) soon be a further downgrade from
"Maintained" to "Odd Fixes" or "Orphan", unless some funding miracle
occurs.  So, if anyone is looking to become man-pages maintainer, there
may soon be an opening (okay, don't trample me in the rush ;-).)
Signed-off-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The 'battery remaining capacity' calculation in
drivers/power/ds2760_battery.c lacks a parameter check to a division
operation which causes the kernel to oops on my board.

[   21.233750] Division by zero in kernel.
[   21.237646] [<c002955c>] (__div0+0x0/0x20) from [<c012561c>] (Ldiv0+0x8/0x10)
[   21.244816] [<c01bef34>] (ds2760_battery_read_status+0x0/0x2a4) from [<c01bf3a4>] (ds2760_battery_get_property+0x30/0xdc)
[   21.255803]  r8:c03a22c0 r7:c7886100 r6:00000009 r5:c782fe7c r4:c7886084
[   21.262518] [<c01bf374>] (ds2760_battery_get_property+0x0/0xdc) from [<c01bde98>] (power_supply_show_property+0x48/0x114)
[   21.273480]  r6:c7996000 r5:00000009 r4:00000000
[   21.278111] [<c01bde50>] (power_supply_show_property+0x0/0x114) from [<c01be158>] (power_supply_uevent+0x188/0x280)
[   21.288537]  r8:00000001 r7:c7886100 r6:c7996000 r5:000000b4 r4:00000000
[   21.295222] [<c01bdfd0>] (power_supply_uevent+0x0/0x280) from [<c015c664>] (dev_uevent+0xd4/0x10c)
[   21.304199] [<c015c590>] (dev_uevent+0x0/0x10c) from [<c0128440>] (kobject_uevent_env+0x180/0x390)
[   21.313170]  r5:00000000 r4:c78860ac
[   21.316725] [<c01282c0>] (kobject_uevent_env+0x0/0x390) from [<c0128664>] (kobject_uevent+0x14/0x18)
[   21.325850] [<c0128650>] (kobject_uevent+0x0/0x18) from [<c01bdc34>] (power_supply_changed_work+0x5c/0x70)
[   21.335506] [<c01bdbd8>] (power_supply_changed_work+0x0/0x70) from [<c004d290>] (run_workqueue+0xbc/0x144)
[   21.345167]  r4:c7812040
[   21.347716] [<c004d1d4>] (run_workqueue+0x0/0x144) from [<c004d94c>] (worker_thread+0xa8/0xbc)
[   21.356296]  r7:c7812040 r6:c7820b00 r5:c782ffa4 r4:c7812048
[   21.361957] [<c004d8a4>] (worker_thread+0x0/0xbc) from [<c0051008>] (kthread+0x5c/0x94)
[   21.369971]  r7:00000000 r6:c004d8a4 r5:c7812040 r4:c782e000
[   21.375612] [<c0050fac>] (kthread+0x0/0x94) from [<c00403d0>] (do_exit+0x0/0x688)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In sget(), destroy_super(s) is called with s->s_umount held, which makes
lockdep unhappy.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the second fasync_helper() fails, pipe_rdwr_fasync() returns the error
but leaves the file on ->fasync_readers.

This was always wrong, but since 233e70f4
"saner FASYNC handling on file close" we have the new problem.  Because in
this case setfl() doesn't set FASYNC bit, __fput() will not do
->fasync(0), and we leak fasync_struct with ->fa_file pointing to the
freed file.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

W1 master implementations are expected to return 0 or 1 from their
read_bit() function.  However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't.  Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the following warning on x86_64:

LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux: 'memcpy' exported twice. Previous export was in vmlinux

For x86_64, this symbol is already exported from arch/um/sys-x86_64/ksyms.c.
Reported-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Tested-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It is currently impossible to run a user-mode linux machine inside another
user-mode linux (UML on UML).  It breaks after a few instructions.  When
it tries to check whether SYSEMU is installed (the inner) UML receives an
inconsistent result (from the outer UML).

This is the output of a broken attempt:
$ ./linux mem=256m ubd0=cow
Locating the bottom of the address space ... 0x0
Locating the top of the address space ... 0xc0000000
Core dump limits :
        soft - 0
        hard - NONE
Checking that ptrace can change system call numbers...OK
Checking ptrace new tags for syscall emulation...unsupported
Checking syscall emulation patch for ptrace...check_sysemu : expected SIGTRAP, got status = 256
$

The problem is the following:

PTRACE_SYSCALL/SINGLESTEP is currently managed inside arch_ptrace for ARCH=um.

PTRACE_SYSEMU/SUSEMU_SINGLESTEP is not captured in arch_ptrace's switch,
therefore it is erroneously passed back to ptrace_request (in
kernel/ptrace).

This simple patch simply forces ptrace to return an error on
PTRACE_SYSEMU/SUSEMU_SINGLESTEP as it is unsupported on ARCH=um, and fixes
the problem.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Renzo Davoli <renzo@cs.unibo.it>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.

Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>