We should suspend the MAC, before we kill the radio. This gives
the MAC a chance to leave any TX/RX state and it avoids races on
the PHY/RADIO registers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Packet length calculation (which includes frame check sequence)
should take into account whether we add a pad field or not.
Extract the calculation into a helper and use it in both places.

Changes to desc.c
Changes-licensed-under: ISC

Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.

The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:

iwconfig wlan0 power timeout 500m

Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.

Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.

The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.

iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes some locking w.r.t. the lower MAC (firmware).
It also removes a lot of ancient IRQ-locking that's not needed anymore.
We simply suspend the MAC. That's easier and causes less trouble.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes unused parameter and unused local variable in
methods in iwl-tx.c:

- Remove a parameter (is_unicast) from iwl_tx_cmd_build_basic().

- Remove an unused variable name unicast from iwl_tx_skb().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The RX code in ath9k uses sc_keymap to figure out whether a default
key was used. However, the default key entries in sc_keymap were
always set and as such, frames could have been claimed to be decrypted
by hardware when they were not. This can cause problems especially
with TKIP since mac80211 is validating the Michael MIC in the frame
and this will result in MIC failure and potentially TKIP
countermeasures if the frame was not decrypted correctly.

Change key cache slot allocation to mark only the keys that really
have been used in sc_keymap to avoid the issue. The key cache slot
selection routines are now internally avoiding the slots that may be
needed for TKIP group keys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath_reserve_key_cache_slot() was obviously supposed to return an index
to a free slot, not reserved one. This could have caused problems with
hardware revisions that use splitmic.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should fix the timeout issues seen when using wpa_supplicant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In stress testing p54usb, the WARN_ON() in ieee80211_tasklet_handler() was
triggered; however, there is no logging of the received value for packet
type. Adding that feature will improve the warning.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enhance allocation of key cache entries to support multiple pairwise
keys to fix AP mode with more than one associated STA.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It looks like mac80211 may try to send unicast frames to a STA that
does not have a STA entry. We need to make sure that that is caught in
the rate control code before dereferencing STA data.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch checks if the radio is disabled before displaying the tx power
level. Previously when the txpower was set off show_tx_power still
returned the prior power level. Now it will indicate the power has been
turned off.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously we allocate Rx SKB with GFP_ATOMIC flag. This is because we need
to hold a spinlock to protect the two rx_used and rx_free lists operation
in the rxq.

	spin_lock();
	...
	element = rxq->rx_used.next;
	element->skb = alloc_skb(..., GFP_ATOMIC);
	list_del(element);
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

After spliting the rx_used delete and rx_free insert into two operations,
we don't require the skb allocation in an atomic context any more (the
function itself is scheduled in a workqueue).

	spin_lock();
	...
	element = rxq->rx_used.next;
	list_del(element);
	...
	spin_unlock();
	...
	element->skb = alloc_skb(..., GFP_KERNEL);
	...
	spin_lock()
	...
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

This patch should fix the "iwlagn: Can not allocate SKB buffers" warning
we see recently.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rename vars in _iwl_poll_bit() to better reflect the truth.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch removes some useless goto in code cleanup.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This enables one to change the debug level at bit 31.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bring up-to-date some comments on the location of debug files.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds line feed to printk.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch removes unused definition and moves code to proper places.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a typo in ieee80211_send_assoc(), net/mac80211/mlme.c.

The error is usage of a wrong member when building
the ie80211 management frame (it should be assoc_req, and not reassoc_req).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes a parameter (dest) from iwl_fill_beacon_frame() (iwl-agn.c)
 and from iwl3945_fill_beacon_frame(). (iwl-3945.c,iwl-3945.h)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes sure the rate control alg is registered/unregistered
only once for this module.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch does pci_dma_sync_single_for_cpu() before accessing
the header of the frame and queueing the same buffer into h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the possible MAC header pad before reporting TX status to
mac80211. This pad is hardware specific operation and should not be
exposed outside the driver. This fixes the frame body in monitor
interfaces that could be used to check on TX status for transmitted
frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The count field in struct ieee80211_tx_rate does not include the final
successful attempt, so only report retries here.

Fix the struct ieee80211_tx_rate::idx field when MCS was used. It is
supposed to be the MCS index, not an internal index to the rate
control algorithm table.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since we do not currently report HT rates (MCS index) in radiotap
header for HT rates, we should not claim the rate is present. The rate
octet itself is used as padding in this case, so only the it_present
flag needs to be removed in case of HT rates.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>

After the code was modified to use urb anchors ("rtl8187: Use usb anchor
facilities to manage urbs"), rtl8187 began generating an intermittent GPF
on shutdown when using SLUB with debugging enabled. Furthermore, rebooting
the system with a ping running caused a GPF every time. There are two problems:
(1) incorrect locking in the rtl8187_rx_cb() routine, a pre-existing bug that
apparently had not been triggered before, and (2) duplicate freeing of receive
skbs that was probably introduced with the change to anchors.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch simplifies the tx code a bit and will be necessary for
the upcoming stlc45xx<->p54 port.

In detail: we no longer have to tell all back-end drivers directly,
if we want to free a frame right after it was send to the firmware,
or if we do it in the library callback later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch replaces the static rssi auto calibration data
with more precise values out of the device's eeprom.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are two places in the rtl8187 code where a routine was returning zero
(OK) when it should have been returning an error.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves a good chunk of code from the former statistic update
timer routine into a workqueue, which is kindly provided by mac80211.

Also as a nice side-effect we can lay the foundation for other
essential housekeeping features we want to do in the future.
e.g:
 - drain the (clogged) tx_queue.
 - initiate bursts.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

    Rate scaling in agn can be broken because of these two problems
    1- the LQ command could not sent, we try to call LQ command before
       post association will be rejected, this will cause the driver to
       break in rs_tx_status reporting initial rate does not match.
    2- In rs_rate_init we can get a value of 12, rate 60, for
       last_txrate_idx, this rate only valid in SISO/MIMO mode only
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a STA roams back to the same AP before the previous STA entry has
expired, a new STA entry is not added in mac80211. However, a Layer 2
Update frame still needs to be transmitted to update layer 2 devices
about the new location for the STA. Without this, switches may
continue to forward frames to the previous (now incorrect) port when
STA roams between APs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Padding the 802.11 header to a multiple of 4 bytes needs to be done only for
frames with a body. This fixes a bug where 2 bytes were missing in monitor
mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k.

Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 :
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix and clean up the RX status reporting by getting rid of code that
used internal rate tables and ratekbps calculation. The correct value
is now reported with MCS index instead of the old mechanism that
defaulted to using the highest legacy rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>