This patch improves UBI errors handling. ATM UBI switches to
R/O mode when the WL worker fails to read the source PEB.
This means that the upper layers (e.g., UBIFS) has no
chances to unmap the erroneous PEB and fix the error.
This patch changes this behaviour and makes UBI put PEBs
like this into a separate RB-tree, thus preventing the
WL worker from hitting the same read errors again and
again.

But there is a 10% limit on a maximum amount of PEBs like this.
If there are too much of them, UBI switches to R/O mode.

Additionally, this patch teaches UBI not to panic and
switch to R/O mode if after a PEB has been copied, the
target LEB cannot be read back. Instead, now UBI cancels
the operation and schedules the target PEB for torturing.

The error paths has been tested by ingecting errors
into 'ubi_eba_copy_leb()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch fixes the error path in the WL worker - in same cases
UBI oopses when 'goto out_error' happens and e1 or e2 are NULL.
This patch also cleans up the error paths a little. And I have
tested nearly all error paths in the WL worker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch is a clean-up and a preparation for the following
patches. It introduece constants for the return values of the
'ubi_eba_copy_leb()' function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch fixes a minor problem where we may fail to wake
upe the UBI background thread. This is not fatal at all,
it may just result at sligtly worse performace for a short
period of time, just because the thread will be woken up
when real I/O on the UBI starts.

Anywey, the issue is the race condition between
'ubi_attach_mtd_dev()' and 'ubi_thread()'. If we do not
serialize them, the 'wake_up_process()' call may be done
before 'ubi_thread()' went seep, but after it checked
'ubi->thread_enabled'.

This issue was spotted by Shin Hong <hongshin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

The @vol->upd_marker should be protected by the @ubi->device_mutex,
otherwise 'paranoid_check_volume()' complains sometimes because
vol->upd_marker is 1 while vtbl_rec->upd_marker is 0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

If a volume paranoid check fails, do not return an error
code to the caller, but just print error messages and go
forward. The primary reason for this is that it is difficult
to recover and cancel the operation at that stage.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

I am experiencing an error in 'paranoid_check_volume()'. Add
dump_stack() there to make it easier to identify the reasons
of the error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

When paranoid checs are enabled, the 'io_paral' test from the
'mtd-utils' package fails. The symptoms are:

UBI error: paranoid_check_all_ff: flash region at PEB 3973:512, length 15872 does not contain all 0xFF bytes
UBI error: paranoid_check_all_ff: paranoid check failed for PEB 3973
UBI: hex dump of the 512-16384 region

It turned out to be a bug in the checking function. Suppose there
are 2 tasks - A and B. Task A is the wear-levelling working
('wear_leveling_worker()'). It is reading the VID header to find
which LEB this PEB belongs to. Say, task A is reading header
of PEB X. Suppose PEB X is unmapped, and has no VID header.
Task B is trying to write to PEB X.

Task A: in 'ubi_io_read_vid_hdr()': reads the VID header from PEB X.
        The read data contain all 0xFF bytes.
Task B: writes VID header and some data to PEB X
Task A: assumes PEB X is empty, calls 'paranoid_check_all_ff()', which
        fails.

The solution for this problem is to make 'paranoid_check_all_ff()'
re-read the VID header, re-check it, and only if it is not there,
check the rest. This now implemented by the 'paranoid_check_empty()'
function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

The @ubi->dbg_peb_buf is needed only when paranoid checks are
enabled, not when debugging in general is enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

Various minor improvements to the debugging messages which
I found useful while hunting problems.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

The mutex essencially protects the entire UBI device, so the
old @volumes_mutex name is a little misleading.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

The @mult_mutex does not serve any purpose. We already have
@volumes_mutex and it is enough. The @volume mutex is pushed
down to the 'ubi_rename_volumes()', because we want first
to open all volumes in the exclusive mode, and then lock the
mutex, just like all other ioctl's (remove, re-size, etc) do.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI MSI: Fix MSI-X with NIU cards
  PCI: Fix pci-e port driver slot_reset bad default return value

* git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6:
  Bluetooth: Don't trigger disconnect timeout for security mode 3 pairing
  Bluetooth: Don't use hci_acl_connect_cancel() for incoming connections
  Bluetooth: Fix wrong module refcount when connection setup fails

Another case of me handling the fallout from Davem's unfortunate
addiction to shuffleboard.

Won't anybody think of the children? Join the anti-shuffleboard league
today!

* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
  drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
  drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
  drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
  drm/i915: ignore LVDS on intel graphics systems that lie about having it
  drm/i915: sanity check IER at wait_request time
  drm/i915: workaround IGD i2c bus issue in kernel side (v2)
  drm/i915: Don't allow binding objects into the last page of the aperture.
  drm/i915: save/restore fence registers across suspend/resume
  drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.

* 'upstream-linus' of ssh://master.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: Media rotation rate and form factor heuristics
  libata: Report disk alignment and physical block size
  sata_fsl: Fix the command description of FSL SATA controller
  sata_fsl: Fix compile warnings
  [libata] sata_sx4: fixup interrupt handling
  [libata] sata_sx4: convert to new exception handling methods

* git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
  iwlwifi: fix device id registration for 6000 series 2x2 devices
  ath5k: update channel in sw state after stopping RX and TX
  rtl8187: use DMA-aware buffers with usb_control_msg
  mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
  airo: airo_get_encode{,ext} potential buffer overflow

Pulled directly by Linus because Davem is off playing shuffle-board at
some Alaskan cruise, and the NULL ptr deref issue hits people and should
get merged sooner rather than later.

David - make us proud on the shuffle-board tournament!

This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.

This patch is based upon code from Matthew Wilcox' 4KB ATA tree.  I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'.  This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.

This has already been fixed for sata_promise:

commit 51b94d2a
Author: Tejun Heo <htejun@gmail.com>
Date:   Fri Jun 8 13:46:55 2007 -0700

    sata_promise: use TF interface for polling NODATA commands

Also, this patch includes Mikael's original patches:

http://marc.info/?l=linux-ide&m=121135828227724&w=2
http://marc.info/?l=linux-ide&m=121144512109826&w=2Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Fix race in ext4_inode_info.i_cached_extent
  ext4: Clear the unwritten buffer_head flag after the extent is initialized
  ext4: Use a fake block number for delayed new buffer_head
  ext4: Fix sub-block zeroing for writes into preallocated extents

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: DaVinci EVM board support buildfixes
  ASoC: DaVinci I2S updates
  ASoC: davinci-pcm buildfixes
  ALSA: pcsp: fix printk format warning
  ALSA: riptide: postfix increment and off by one
  pxa2xx-ac97: fix reset gpio mode setting
  ASoC: soc-core: fix crash when removing not instantiated card

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdb: gdb documentation fix
  kgdb,i386: use address that SP register points to in the exception frame
  sysrq, intel_fb: fix sysrq g collision

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "mm: add /proc controls for pdflush threads"
  viocd: needs to depend on BLOCK
  block: fix the bio_vec array index out-of-bounds test

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix PCI ROM access
  powerpc/pseries: Really fix the oprofile CPU type on pseries
  serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
  powerpc/cell: Make ptcal more reliable
  powerpc: Allow mem=x cmdline to work with 4G+
  powerpc/mpic: Fix incorrect allocation of interrupt rev-map
  powerpc: Fix oprofile sampling of marked events on POWER7
  powerpc/iseries: Fix pci breakage due to bad dma_data initialization
  powerpc: Fix mktree build error on Mac OS X host
  powerpc/virtex: Fix duplicate level irq events.
  powerpc/virtex: Add uImage to the default images list
  powerpc/boot: add simpleImage.* to clean-files list
  powerpc/8xx: Update defconfigs
  powerpc/embedded6xx: Update defconfigs
  powerpc/86xx: Update defconfigs
  powerpc/85xx: Update defconfigs
  powerpc/83xx: Update defconfigs
  powerpc/fsl_soc: Remove mpc83xx_wdt_init, again

devpts_get_sb() calls memset(0) to clear mount options and calls
parse_mount_options() if user specified any mount options.

The memset(0) is bogus since the 'mode' and 'ptmxmode' options are
non-zero by default.  parse_mount_options() restores options to default
anyway and can properly deal with NULL mount options.

So in devpts_get_sb() remove memset(0) and call parse_mount_options() even
for NULL mount options.

Bug reported by Eric Paris: http://lkml.org/lkml/2009/5/7/448.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Reported-by: Eric Paris <eparis@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Reviewed-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* fix/asoc:
  ASoC: DaVinci EVM board support buildfixes
  ASoC: DaVinci I2S updates
  ASoC: davinci-pcm buildfixes
  pxa2xx-ac97: fix reset gpio mode setting
  ASoC: soc-core: fix crash when removing not instantiated card

* fix/misc:
  ALSA: pcsp: fix printk format warning
  ALSA: riptide: postfix increment and off by one

If two CPU's simultaneously call ext4_ext_get_blocks() at the same
time, there is nothing protecting the i_cached_extent structure from
being used and updated at the same time.  This could potentially cause
the wrong location on disk to be read or written to, including
potentially causing the corruption of the block group descriptors
and/or inode table.

This bug has been in the ext4 code since almost the very beginning of
ext4's development.  Fortunately once the data is stored in the page
cache cache, ext4_get_blocks() doesn't need to be called, so trying to
replicate this problem to the point where we could identify its root
cause was *extremely* difficult.  Many thanks to Kevin Shanahan for
working over several months to be able to reproduce this easily so we
could finally nail down the cause of the corruption.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>

gdb command "set remote debug 1" is not valid, change to correct command.
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

The treatment of the SP register is different on x86_64 and i386.
This is a regression fix that lived outside the mainline kernel from
2.6.27 to now.  The regression was a result of the original merge
consolidation of the i386 and x86_64 archs to x86.

The incorrectly reported SP on i386 prevented stack tracebacks from
working correctly in gdb.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>

Commit 79e53945 introduced a
regression where you cannot use sysrq 'g' to enter kgdb.  The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics.  The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.

This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

This reverts commit fafd688e.

Work is progressing to switch away from pdflush as the process backing
for flushing out dirty data. So it seems pointless to add more knobs
to control pdflush threads. The original author of the patch did not
have any specific use cases for adding the knobs, so we can easily
revert this before 2.6.30 to avoid having to maintain this API
forever.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree.  That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.

(NOTE:  also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This resyncs the DaVinci I2S code with the version in the DaVinci
tree.  The behavioral change uses updated clock interfaces which
recently merged to mainline.  Two other changes include adding a
comment on the ASP/McBSP/McASP confusion, and dropping pdev->id in
order to support more boards than just the DM644x EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is a buildfix for the DaVinci PCM code, resyncing it with
the version in the DaVinci tree.  The notable change is using
current EDMA interfaces, which recently merged to mainline.
(The older interfaces never made it into mainline.)

NOTE:  open issue, the DMA should be to/from SRAM; see chip
errata for more info.  The artifacts are extremely easy to
hear on DM355 hardware (not yet supported in mainline), but
don't seem as audible on DM6446 hardwaare (which does have
mainline support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>