This patch (as798) adds a workaround to uhci-hcd.  At least one Asus
motherboard is wired in such a way that any device attached to a
suspended UHCI controller will prevent the system from entering
suspend-to-RAM by immediately waking it up.  The only way around the
problem is to turn the controller off instead of suspending it.

This fixes Bugzilla #6193.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Deleted some unused code that could do bad things on non-x86 platforms.

Also fixed some minor formatting errors.

Thanks to Al Viro for pointing out the sparse errors.

Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this implements suspend support for usblp. According to the CUPS people
ENODEV will make CUPS retry the job. Thus it is returned in the runtime
case. My printer survives suspend/resume cycles with it.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 From http://doc.ubuntu-fr.org/materiel/zxdsl852.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The speedtouch modem setup code was reverse engineered many years
ago from a prehistoric windows driver. Less ancient windows drivers,
even those from a few years ago, perform extra initialization steps
which this patch adds to the linux driver.  David Woodhouse observed
that this initialization along with the firmware bin/sachu3/zzzlp2.eni
from the driver at
http://www.speedtouch.co.uk/downloads/330/301/UK3012%20Extended.zip
improves line sync speeds by about 20%.  He provided the original
patch, which I've modified to use symbolic names (BMaxDSL, ModemMode,
ModemOption) rather than magic numbers.  These names may not seem like
much of an improvement (after all, what is "ModemOption" exactly?),
but they do have one big advantage: they are the names used in the
windows registry.  I've made them available as module parameters.
Thanks are due to Aurelio Arroyo, who noticed the relationship
between these magic numbers and the entries in Phonebook.ini.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If usbatm_do_heavy_init finishes before usbatm_heavy_init
writes the pid, the disconnect method could shoot down the
wrong process if the pid has been recycled.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as796) adds an unusual_devs entry for the Nokia 6131, which
doesn't like large transfer sizes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Hi,

this patch does some cosmetic changes :
- dump firwmare version as soon as possible and export it on sysfs
- hint about wrong cmv/dsp
- Display a message to warn user when the modem is ready : it can help
  people to detect problems on the line without debug trace
- Fix wrong indent
- display modem type (pots/isdn)
- increase version number
Signed-off-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this patch use wait_event_interruptible_timeout and msleep_interruptible
beacause uninterruptible sleep (task state 'D') is counted as 1 towards
load average, like running processes.
Signed-off-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this patch avoid that the kernel thread block the suspend process.
Some work is still need to recover after a resume.
Signed-off-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The OHCI bus glue for the Philips PNX chips is missing a few calls.

 - Bus suspend/resume were wrongly omitted in the original submission.
 - Two new calls were added since that glue was submitted:
     * Root hub irq enable call
     * Shutdown hook for usbcore

Plus usb_bus.hcpriv has now been removed from usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this adds support for suspend and resume to the kaweth driver.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this kills the private debug macros from the kaweth driver.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The patch below is a necessary workaround to support the BT On-Air USB modem, which
fails to initialise properly during normal probing thus:

Sep 30 17:34:57 sled kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
Sep 30 17:34:57 sled kernel: cdc_acm: probe of 1-1.2:1.0 failed with error -22

Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Adds support for the verizon wireless Broadband Access, National Access V640
ExpressCard34 Qualcomm 3G CDMA.

Reported by Maciej A. __enczykowski <maze@google.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

the following commit added a use after free
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3D3bea733ab21247290bd552dd6a2cd3049af9adef
Found by coverity (cid #1441)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: "Ping Cheng" <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this patch converts two if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: "Ping Cheng" <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This fixes some issues with the current wacom driver due to the split of
the driver into different pieces and adds support for the Intuos3 4x6
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This reverts 26f953fd which caused
resume problems on the mac mini.

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it hangs after a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

When using flow control, the PHY needs to accept multicast pause frames.
Without this fix, these frames were getting discarded by the PHY before
doing any flow control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

Mark version, this has been a lot of patches.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

Under high load it is possible to make the receiver FIFO get overloaded.
The driver/hardware recover properly, so there is no reason to fill the log
with lots of extra messages, just update counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

The result of flow control negotiation should not limit the next
negotiatition. If board is plugged into an old half duplex 10Mbit port,
without pause, then replugged into a gigabit port, it should negotiate
what is desired, not inherit that last negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

Don't need to reset PHY twice on startup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

The result of duplex negotiation is avaliable in the phy status
register, so use that to simplify code and avoid rereading the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

The advertising bits (from ethtool.h) fit in 16 bits.

The advertisement bits for flow control are located in
different location on fiber (1000baseX)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

When PHY is turned off on shutdown, it causes the IRQ to get stuck on.
Make sure and disable the IRQ first, and if IRQ occurs when device
is not running, don't access PHY because that will hang.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

The workaround timer is not needed in most systems with proper IRQ
routing and by perodically waking up it adds to laptop power consumption.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

Some motherboards don't implement MSI correctly. The driver handles this
but the warning is too verbose and overly cautious.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: fm801-gp - handle errors from pci_enable_device()
  Input: gameport core - handle errors returned by device_bind_driver()
  Input: serio core - handle errors returned by device_bind_driver()
  Lockdep: fix compile error in drivers/input/serio/serio.c
  Input: serio - add lockdep annotations
  Lockdep: add lockdep_set_class_and_subclass() and lockdep_set_subclass()
  Input: atkbd - supress "too many keys" error message
  Input: i8042 - supress ACK/NAKs when blinking during panic
  Input: add missing exports to fix modular build

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Check for offline nodes in pci NUMA code
  [POWERPC] Better check in show_instructions
  [POWERPC] POWER6 has 6 PMCs
  [POWERPC] Never panic when taking altivec exceptions from userspace
  [POWERPC] Fix IO Window Updates on P2P bridges.
  [POWERPC] Add Makefile entry for MPC832x_mds support
  [POWERPC] Fix MPC8360EMDS PB board support
  [POWERPC] ppc: Add missing calls to set_irq_regs
  [POWERPC] Off-by-one in /arch/ppc/platforms/mpc8*
  [POWERPC] Add DOS partition table support to mpc834x_itx_defconfig
  [POWERPC] spufs: fix support for read/write on cntl
  [POWERPC] Don't crash on cell with 2 BEs when !CONFIG_NUMA

Most of the ISDN ->readstat() implementations needed to check
copy_to_user() and put_user() return values.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This is a particularly ugly on-failure bug, possibly security, since the
lack of error handling here is covering up another class of bug: failure to
handle copy_to_user() return values.

The I4L API function ->readstat() returns an integer, and by looking at
several existing driver implementations, it is clear that a negative return
value was meant to indicate an error.

Given that several drivers already return a negative value indicating an
errno-style error, the current code would blindly accept that [negative]
value as a valid amount of bytes read.  Obvious damage ensues.

Correcting ->readstat() handling to properly notice errors fixes the
existing code to work correctly on error, and enables future patches to
more easily indicate errors during operation.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Karsten Keil <kkeil@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

With Karsten Keil <kkeil@suse.de>

save_flags()/cli() pair is replaced with spin_lock_irqsave() and
restore_flags() replaced with spin_unlock_irqrestore()

Tested compile only using allmodconfig
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The use of blocking notifier by _cpu_up and _cpu_down in cpu.c has two
problem.

1/ An interaction with the workqueue notifier causes lockdep to spit a
   warning.

2/ A notifier could conceivable be added or removed while _cpu_up or
   _cpu_down are in process.  As each notifier is called twice (prepare
   then commit/abort) this could be unhealthy.

To fix to we simply take cpu_add_remove_lock while adding or removing
notifiers to/from the list.

This makes the 'blocking' usage unnecessary as all accesses to cpu_chain
are now protected by cpu_add_remove_lock.  So change "blocking" to "raw" in
all relevant places.  This fixes 1.

Credit: Andrew Morton
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com> (reporter)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

BUG: warning at kernel/rtmutex-debug.c:125/rt_mutex_debug_task_free() (Not tainted)
 [<c04051e3>] show_trace_log_lvl+0x58/0x16a
 [<c04057f0>] show_trace+0xd/0x10
 [<c0405900>] dump_stack+0x19/0x1b
 [<c043f03d>] rt_mutex_debug_task_free+0x35/0x6a
 [<c04224c0>] free_task+0x15/0x24
 [<c042378c>] copy_process+0x12bd/0x1324
 [<c0423835>] do_fork+0x42/0x113
 [<c04021dd>] sys_fork+0x19/0x1b
 [<c0403fb7>] syscall_call+0x7/0xb

In copy_process(), dup_task_struct() also duplicates the ->pi_lock,
->pi_waiters and ->pi_blocked_on members.  rt_mutex_debug_task_free()
called from free_task() validates these members.  However free_task() can
be invoked before these members are reset for the new task.

Move the initialization code before the first bail that can hit free_task().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>