- 06 Mar, 2010 40 commits
-
-
Wolfgang Muees authored
Fix two timeout errors, one for slow SDHC cards and one for slow users while inserting SD cards. Signed-off-by:
Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Wolfgang Muees authored
Fixes two pointer errors, one which leads to memory overwrites if used with large chunks of data. Signed-off-by:
-
Lars-Peter Clausen authored
Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Cc: Ben Dooks <ben-linux@fluff.org> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
If no platform_data was givin to the device it's going to use it's default platform data struct which has all fields initialized to zero. As a result the driver is going to try to request gpio0 both as write protect and card detect pin. Which of course will fail and makes the driver unusable Previously to the introduction of no_wprotect and no_detect the behavior was to assume that if no platform data was given there is no write protect or card detect pin. This patch restores that behavior. Signed-off-by:
-
Daniel Drake authored
And bring them back to 4-bit mode during resume. Signed-off-by:
Daniel Drake <dsd@laptop.org> Signed-off-by:
Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Nicolas Pitre authored
Some SDIO cards may suspend while keeping function interrupts active especially in the powered suspend case. Upon resume we need to kick the SDIO interrupt thread to check for pending interrupts and to restart card IRQ detection at the host controller level. Signed-off-by:
-
Chris Ball authored
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid sending CMD3/5/7 on a resume where power has been maintained, because the 8686 will refuse to respond to them and the MMC stack will give up on the card. Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Nicolas Pitre authored
Tested with an XO v1.5 from OLPC. Signed-off-by:
-
Nicolas Pitre authored
This patch series provides the core changes needed to allow SDIO cards to remain powered and active while the host system is suspended, and let them wake up the host system when needed. This is used to implement wake-on-lan with SDIO wireless cards at the moment. Patches to add that support to the libertas driver will be posted separately. This patch: Some SDIO cards have the ability to keep on running autonomously when the host system is suspended, and wake it up when needed. This however requires that the host controller preserve power to the card, and configure itself appropriately for wake-up. There is however 4 layers of abstractions involved: the host controller driver, the MMC core code, the SDIO card management code, and the actual SDIO function driver. To make things simple and manageable, host drivers must advertise their PM capabilities with a feature bitmask, then function drivers can query and set those features from their suspend method. Then each layer in the suspend call chain is expected to act upon those bits accordingly. [akpm@linux-foundation.org: fix typo in comment] Signed-off-by:
-
Ben Dooks authored
sdhci_set_adma_desc() is using byte-writes to write data in a specified order into memory. Change to using __le16 for the two byte and __le32 for the four byte cases and use the cpu_to_{le16,le32} to do the conversion before writing. This will reduce the size of the code and the number of writes as we no longer need to chop the data up before writing. As an example on ARM S3C64XX SoC, in little-endian configuration: 000000d4 <sdhci_set_adma_desc>: - d8: e1a0c423 lsr ip, r3, #8 - dc: e1a0ec21 lsr lr, r1, #24 - e0: e1a04821 lsr r4, r1, #16 - e4: e1a05421 lsr r5, r1, #8 - e8: e1a06442 asr r6, r2, #8 - ec: e5c0c001 strb ip, [r0, #1] - f0: e5c0e007 strb lr, [r0, #7] - f4: e5c04006 strb r4, [r0, #6] - f8: e5c05005 strb r5, [r0, #5] - fc: e5c01004 strb r1, [r0, #4] - 100: e5c06003 strb r6, [r0, #3] - 104: e5c02002 strb r2, [r0, #2] - 108: e5c03000 strb r3, [r0] + d4: e5801004 str r1, [r0, #4] + d8: e1c030b0 strh r3, [r0] + dc: e1c020b2 strh r2, [r0, #2] Signed-off-by:Ben Dooks <ben-linux@fluff.org> Cc: Pierre Ossman <pierre@ossman.eu> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Ben Dooks authored
The code to write the ADMA descriptor into memory is repeated several times throughout sdhci_adma_table_pre, and thus should be moved into a common function. This will also be useful if the patch to make the write more efficient is accepted. Signed-off-by:
-
Bing Zhao authored
Some SDIO cards expect byte transfers not to exceed the configured block transfer size. Add a quirk to that effect. Patches to make use of this quirk will be sent separately. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Cliff Cai authored
The hardcoded value doesn't really work for all cards. Signed-off-by:
Cliff Cai <cliff.cai@analog.com> Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Mike Frysinger authored
The host/Kconfig file is only included when MMC is selected. Signed-off-by:
-
Mike Frysinger authored
The local sg variable is only used with BF54x code. Signed-off-by:
-
Nicolas Ferre authored
This prevents those without an Atmel chip having a line in kernel configuration which says "Atmel SD/MMC Driver" without any option. Signed-off-by:
Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by:
-
Vipin Bhandari authored
Add support for 8bit MMC cards. The controller data width is configurable depending on the wires setting in the platform data structure. MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM. Signed-off-by:
Vipin Bhandari <vipin.bhandari@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Chaithrika U S <chaithrika@ti.com> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Maxim Levitsky authored
This patch solves nasty problem original driver has. Original goal of the ricoh_mmc was to disable this device because then, mmc cards can be read using standard SDHCI controller, thus avoiding writing of yet another driver. However, the act of disablement, makes other pci functions that belong to this controller (xD and memstick) shift up one level, thus pci core has now wrong idea about these devices. To fix this issue, this patch moves the driver into the pci quirk section, thus it is executes before the pci is enumerated, and therefore solving that issue, also same sequence of commands is performed on resume for same reasons. Also regardless of the above, this way is cleaner. You still need to set CONFIG_MMC_RICOH_MMC to enable this quirk Signed-off-by:
Maxim Levitsky <maximlevitsky@gmail.com> Acked-by:
Philip Langdale <philipl@overt.org> Acked-by:
Wolfram Sang <w.sang@pengutronix.de> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Andrew Morton authored
fs/compat_ioctl.c: In function 'do_ioctl_trans': fs/compat_ioctl.c:534: warning: 'karg' may be used uninitialized in this function fs/compat_ioctl.c:533: warning: 'kcmd' may be used uninitialized in this function fs/compat_ioctl.c:656: warning: 'ret' may be used uninitialized in this function Reduces text size by 44 bytes. If someone calls one of these functions with an unexpected argument, the code's buggy as-is. Amerigo Wang <amwang@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Akinobu Mita authored
Replace open-coded loop with for_each_set_bit(). Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Ben Hutchings authored
The function name must be followed by a space, hypen, space, and a short description. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Don Mullis authored
Build list_sort() only for configs that need it -- those that don't save ~581 bytes (i386). Signed-off-by:
Don Mullis <don.mullis@gmail.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Artem Bityutskiy <dedekind@infradead.org> Signed-off-by:
-
Don Mullis authored
Clarify and correct header comment of list_sort(). Signed-off-by:
-
Don Mullis authored
XFS and UBIFS can pass long lists to list_sort(); this alternative implementation scales better, reaching ~3x performance gain when list length exceeds the L2 cache size. Stand-alone program timings were run on a Core 2 duo L1=32KB L2=4MB, gcc-4.4, with flags extracted from an Ubuntu kernel build. Object size is 581 bytes compared to 455 for Mark J. Roberts' code. Worst case for either implementation is a list length just over a power of two, and to roughly the same degree, so here are timing results for a range of 2^N+1 lengths. List elements were 16 bytes each including malloc overhead; initial order was random. time (msec) Tatham-Roberts | generic-Mullis-v2 loop_count length | | ratio 4000000 2 206 294 1.427 2000000 3 176 227 1.289 1000000 5 199 172 0.864 500000 9 235 178 0.757 250000 17 243 182 0.748 125000 33 261 196 0.750 62500 65 277 209 0.754 31250 129 292 219 0.75 15625 257 317 235 0.741 7812 513 340 252 0.741 3906 1025 362 267 0.737 1953 2049 388 283 0.729 ~ L1 size 976 4097 556 323 0.580 488 8193 678 361 0.532 244 16385 773 395 0.510 122 32769 844 418 0.495 61 65537 917 454 0.495 30 131073 1128 543 0.481 15 262145 2355 869 0.369 ~ L2 size 7 524289 5597 1714 0.306 3 1048577 6218 2022 0.325 Mark's code does not actually implement the usual or generic mergesort, but rather a variant from Simon Tatham described here: http://www.chiark.greenend.org.uk/~sgtatham/algorithms/listsort.html Simon's algorithm performs O(log N) passes over the entire input list, doing merges of sublists that double in size on each pass. The generic algorithm instead merges pairs of equal length lists as early as possible, in recursive order. For either algorithm, the elements that extend the list beyond power-of-two length are a special case, handled as nearly as possible as a "rounding-up" to a full POT. Some intuition for the locality of reference implications of merge order may be gotten by watching this animation: http://www.sorting-algorithms.com/merge-sort Simon's algorithm requires only O(1) extra space rather than the generic algorithm's O(log N), but in my non-recursive implementation the actual O(log N) data is merely a vector of ~20 pointers, which I've put on the stack. Long-running list_sort() calls: If the list passed in may be long, or the client's cmp() callback function is slow, the client's cmp() may periodically invoke cond_resched() to voluntarily yield the CPU. All inner loops of list_sort() call back to cmp(). Stability of the sort: distinct elements that compare equal emerge from the sort in the same order as with Mark's code, for simple test cases. A boot-time test is provided to verify this and other correctness requirements. A kernel that uses drm.ko appears to run normally with this change; I have no suitable hardware to similarly test the use by UBIFS. [akpm@linux-foundation.org: style tweaks, fix comment, make list_sort_test __init] Signed-off-by: -
André Goddard Rosa authored
Signed-off-by:
André Goddard Rosa <andre.goddard@gmail.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Joe Perches <joe@perches.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by:
-
André Goddard Rosa authored
Removes 32 bytes on core2 with gcc 4.4.1: text data bss dec hex filename 3196 0 0 3196 c7c lib/string-BEFORE.o 3164 0 0 3164 c5c lib/string-AFTER.o Signed-off-by:
-
Joe Perches authored
Patchwork queues show the acceptance/rejection state of submitted patches for various MAINTAINER trees. Document their existence. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
by commit 0234f84e Update patterns Signed-off-by:
-
Joe Perches authored
by commit 955015bbSigned-off-by:
-
Joe Perches authored
To match arch/*/kernel perf_event location changes Signed-off-by:
-
Joe Perches authored
Commit f53a2ade ("tty: esp: remove broken driver") removed it Signed-off-by:
-
Joe Perches authored
Commit c95d1e53 ("cs5535: drop the Geode-specific MFGPT/GPIO code") removed it. Signed-off-by:
-
Joe Perches authored
If MAINTAINERS section entries are misformatted, it was possible to have an infinite loop. Correct the defect by always moving the index to the end of section + 1 Also, exit check for exclude as soon as possible. Signed-off-by:
-
Stephen Hemminger authored
Picky mail systems won't accept email addresses where recipient has period in name; ie. David S. Miller <davemloft.net> will not work. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Acked-by:
-
Stephen Hemminger authored
perlcritic is a standard checker for Perl Best Practices. This patch fixes most of the warnings in the get_maintainer script. If kernel programmers are going to have checkpatch they should write clean scripts as well... Bareword file handle opened at line 176, column 1. See pages 202,204 of PBP. (Severity: 5) Two-argument "open" used at line 176, column 1. See page 207 of PBP. (Severity: 5) Bareword file handle opened at line 207, column 5. See pages 202,204 of PBP. (Severity: 5) Two-argument "open" used at line 207, column 5. See page 207 of PBP. (Severity: 5) Bareword file handle opened at line 246, column 6. See pages 202,204 of PBP. (Severity: 5) Two-argument "open" used at line 246, column 6. See page 207 of PBP. (Severity: 5) Bareword file handle opened at line 258, column 2. See pages 202,204 of PBP. (Severity: 5) Two-argument "open" used at line 258, column 2. See page 207 of PBP. (Severity: 5) Expression form of "eval" at line 983, column 17. See page 161 of PBP. (Severity: 5) Expression form of "eval" at line 985, column 17. See page 161 of PBP. (Severity: 5) Subroutine prototypes used at line 1186, column 1. See page 194 of PBP. (Severity: 5) Subroutine prototypes used at line 1206, column 1. See page 194 of PBP. (Severity: 5) Signed-off-by:
-
Joe Perches authored
Doesn't need or accept '-' as a trailing option to read stdin. Doesn't print usage() after bad options. Adds --usage as command line equivalent of --help Suggested-by:
Borislav Petkov <petkovbb@googlemail.com> Signed-off-by:
-
Joe Perches authored
Signed-off-by:
-
Joe Perches authored
Print the complete contents of the matched subsystems in pattern match depth order. Sample output: $ ./scripts/get_maintainer.pl --sections -f drivers/net/usb/smsc95xx.c USB SMSC95XX ETHERNET DRIVER M:Steve Glendinning <steve.glendinning@smsc.com> L:netdev@vger.kernel.org S:Supported F:drivers/net/usb/smsc95xx.* USB SUBSYSTEM M:Greg Kroah-Hartman <gregkh@suse.de> L:linux-usb@vger.kernel.org W:http://www.linux-usb.org T:quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/ S:Supported F:Documentation/usb/ F:drivers/net/usb/ F:drivers/usb/ F:include/linux/usb.h F:include/linux/usb/ NETWORKING DRIVERS L:netdev@vger.kernel.org W:http://www.linuxfoundation.org/en/Net T:git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git S:Odd Fixes F:drivers/net/ F:include/linux/if_* F:include/linux/*device.h THE REST M:Linus Torvalds <torvalds@linux-foundation.org> L:linux-kernel@vger.kernel.org Q:http://patchwork.kernel.org/project/LKML/list/ T:git git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git S:Buried alive in reporters F:* F:*/ Signed-off-by:
-
Joe Perches authored
Add an imperfect option to search a source file for email addresses. New option: --file-emails or --fe email addresses in files are freeform text and are nearly impossible to parse. Still, might as well try to do a somewhat acceptable job of finding them. This code should find all addresses that are in the form addr@domain.tld The code assumes that up to 3 alphabetic words along with dashes, commas, and periods that preceed the email address are a name. If 3 words are found for the name, and one of the first two words are a single letter and period, or just a single letter then the 3 words are use as name otherwise the last 2 words are used. Some variants that are shown correctly: John Smith <jksmith@domain.org> Random J. Developer <rjd@tld.com> Random J. Developer (rjd@tld.com) J. Random Developer rjd@tld.com Variants that are shown nominally correctly: Written by First Last (funny-addr@somecompany.com) is shown as: First Last <funny-addr@somecompany.com> Variants that are shown incorrectly: Some Really Long Name <srln@foo.bar> MontaVista Software, Inc. <source@mvista.com> are returned as: Long Name <srln@foo.bar> "Software, Inc" <source@mvista.com> --roles and --rolestats show "(in file)" for matches. For instance: Without -file-emails: $ ./scripts/get_maintainer.pl -f -nogit -roles net/core/netpoll.c David S. Miller <davem@davemloft.net> (maintainer:NETWORKING [GENERAL]) linux-kernel@vger.kernel.org (open list) With -fe: $ ./scripts/get_maintainer.pl -f -fe -nogit -roles net/core/netpoll.c David S. Miller <davem@davemloft.net> (maintainer:NETWORKING [GENERAL]) Matt Mackall <mpm@selenic.com> (in file) Ingo Molnar <mingo@redhat.com> (in file) linux-kernel@vger.kernel.org (open list) netdev@vger.kernel.org (open list:NETWORKING [GENERAL]) The number of email addresses in the file in not limited. Neither is the number of returned email addresses. Signed-off-by: -
Gustavo F. Padovan authored
kernel/printk.c:72: warning: `saved_console_loglevel' defined but not used Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
