- 23 Jun, 2009 40 commits
-
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com> Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. The existing code was casting pointers to u32 and to unsigned int into pointers to u16. This could mess up if someone passed in an image size greater than 65,535 and on big-endian platforms it won't work at all. The existing bounding code would shrink an image if it was too big, but returned ERANGE if it was too small. The code will not shrink or expand as necessary. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. Signed-off-by:
-
Trent Piepho authored
The v4l function has a better algorithm for aligning image size. For instance the old code would change 159x243 into 156x240 to meet the alignment requirements. The new function will use 160x243, which is a lot closer to what was asked for originally. Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Trent Piepho authored
Most hardware has limits on minimum and maximum image dimensions and also requirements about alignment. For example, image width must be even or a multiple of four. Some hardware has requirements that the total image size (width * height) be a multiple of some power of two. v4l_bound_align_image() will enforce min and max width and height, power of two alignment on width and height, and power of two alignment on total image size. It uses an efficient algorithm that will try to find the "closest" image size that meets the requirements. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
Add a new s_config core ops call: this is called with the irq and platform data to be used to initialize the subdev. Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls that allows you to pass these new arguments. The existing v4l2_i2c_new_subdev functions were modified to also call s_config. In the future the existing v4l2_i2c_new_subdev functions will be replaced by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg but without the irq and platform_data arguments. Signed-off-by:
-
Mike Isely authored
This change does not change any outward behavior; it merely chops down some large if-conditions with embedded assignments into something a little more maintainable for others (I of course never had a problem with this...). Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Mike Isely authored
The pvrusb2 driver has a concept of "routing scheme" which defines which physical inputs should be connected based on application's choice of logical input. The correct "routing scheme" depends on the specific device since different devices might wire up their muxes Signed-off-by: -
Mike Isely authored
Change default frequency to be US Broadcast channel 3 - with the transition to d igital the previous value has now become useless. This change is PURELY to help with my testing (I need to set some kind of default so it might as well be some thing usable). Signed-off-by:
-
Mike Isely authored
The cx25840 module's VBI initialization logic uses the current video standard as part of its internal algorithm. This therefore means that we probably need to make sure that the correct video standard has been set before initializing VBI. (Normally we would not care about VBI, but as described in an earlier changeset, VBI must be initialized correctly on the cx25840 in order for the chip's hardware scaler to operate correctly.) It's kind of messy to force the video standard to be set before initializing VBI (mainly because we can't know what the app really wants that early in the initialization process). So this patch does the next best thing: VBI is re-initialized after any point where the video standard has been set. Signed-off-by:
-
Mike Isely authored
The cx25840 module requires that its VBI initialization entry point be called in order for hardware-scaled video capture to work properly - even if we don't care about VBI. Making this behavior even more subtle is that if the capture resolution is set to 720x480 - which is the default that the pvrusb2 driver sets up - then the cx25840 bypasses the hardware scaler. Therefore this problem does not manifest itself until some other resolution, e.g. 640x480, is tried. MythTV typically defaults to 640x480 or 480x480, which means that things break whenever the driver is used with MythTV. This all has been known for a while (since at least Nov 2006), but recent changes in the pvrusb2 driver (specifically in regards to sub-device support) caused this to break again. VBI initialization must happen *after* the chip's firmware is loaded, not before. With this fix, 24xxx devices work correctly again. A related fix that is part of this changeset is that now we re-initialize VBI any time after we issue a reset to the cx25840 driver. Issuing a chip reset erases the state that the VBI setup previously did. Until the HVR-1950 came along this subtlety went unnoticed, because the pvrusb2 driver previously never issued such a reset. But with the HVR-1950 we have to do that reset in order to correctly transition from digital back to analog mode - and since the HVR-1950 always starts in digital mode (required for the DVB side to initialize correctly) then this device has never had a chance to work correctly in analog mode! Analog capture on the HVR-1950 has been broken this *ENTIRE* time. I had missed it until now because I've usually been testing at the default 720x480 resolution which does not require scaling... What fun. By re-initializing VBI after a cx25840 chip reset, correct behavior is restored. Signed-off-by:
-
Michael Krufky authored
Ensure that we're programming the tda18271 tuner with the correct IF frequencies to match the programming of the TDA10048 DVB-T demod for the HVR1200 and HVR1700 products. Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Thanks for Terry Wu for pointing out the missing entry. Cc: Terry Wu <terrywu2009@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The variable 'rc' could be used uninitialized in the cx231xx_capture_start function. Sri informed me that it should be initialized to -1. Signed-off-by:
-
Hans Verkuil authored
tcm825x_remove is not necessarily called on module exit, it can also be called when the i2c_adapter is removed. While the i2c adapter might never be removed on an embedded system, in practice this sensor driver can also be used in e.g. a USB webcam where this is a perfectly acceptable thing to do. Signed-off-by:
-
Hans Verkuil authored
rxsubchans was only set when stereo was detected, otherwise it was left to 0 instead of setting it to mono. Signed-off-by:
-
Hans Verkuil authored
Make it very clear that this header should not be used for i2c drivers that do not need to be compiled for pre-2.6.26 kernels. As soon as the minimum supported kernel in the v4l-dvb repository becomes 2.6.26 or up, then this header should be removed entirely. Signed-off-by:
-
Hans Verkuil authored
gcc 4.3.1 generates this warning: v4l/smscoreapi.c: In function 'smscore_gpio_configure': v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function While in practice this will not happen, it is something that the compiler can't determine. Initializing these two local variables to 0 suppresses this warning. Cc: Udi Atar <udi.linuxtv@gmail.com> Signed-off-by:
-
Hans Verkuil authored
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control was broken for all drivers that use the cx2341x module and the USER class control was broken for ivtv and cx18. This change adds back proper class control support. Signed-off-by:
-
Devin Heitmueller authored
Add an IR profile for the EVGA inDtube remote control (which is an NEC type remote) Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Add support for the EVGA inDtube. Both ATSC and analog side validated as fully functional. Thanks to Jake Crimmins from EVGA for providing the correct GPIO info. Thanks to Alan Hagge for doing all the device testing. Thanks to Greg Williamson for providing hardware for testing. Cc: Jake Crimmins <jcrimmins@evga.com> Cc: Alan Hagge <ahagge@gmail.com> Cc: Greg Williamson <cheeseboy16@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
In cases where the board had a default USB ID, we would not indentify the board until after the call to em28xx_set_mode(). As a result, for those boards the analog GPIOs were not being set before probing the i2c bus for devices (the probe would occur with the GPIOs being all high). Make a call to em28xx_set_mode() so that the GPIOs are set properly before probing the i2c bus for devices. This problem was detected with the EVGA inDtube, where the tvp5150 is not powered on unless GPIO1 is pulled low. Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
Igor M. Liplianin <liplianin@netup.ru> Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
Abylay Ospan <aospan@netup.ru> Signed-off-by:
-
Abylay Ospan authored
Signed-off-by:
-
Igor M. Liplianin authored
Signed-off-by:
-
Hans de Goede authored
Name saturation control saturation, not color and make the default less saturated (the old default was overdoing it). Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise the picture is upside down. It is better to instead invert the meaning of the control in the set function, and have the default be no vflip, as one would expect vflip enabled to be upside down. Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: Add light frequency control Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: enable autogain control for the ov7620, and not only make it enable autogain but also auto exposure (and do the same for the ov7648). Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer overflows during my testing of a "Premier" 0c45:613e cam Signed-off-by:
-
Hans de Goede authored
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one cam it supports, is now also supported by the v4l2 gspca stv06xx driver. Signed-off-by:
-
Hans de Goede authored
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak the ov7630 register init values for a much better picture. Signed-off-by:
-
