if it was brought up from halt.  This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend.  Works for both suspend to ram
and hibernation.  The patch has zero effect on the running state.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

The suspend & resume function names are incorrect for the PM=n case.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

function, I got that wrong during my last change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Michael "Tired" Riepe <michael.riepe@googlemail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

{2147, 483648000} on a 32 bit computer (or even for delays as small as
{429, 500000000} if the task is niced).

Because the result was already forced between 0 and 100ms, the effect of
the overflow was not too problematic, but the use of the hrtimer range
feature was not optimal in overflow cases.

This patch ensures that there can not be an integer overflow in this
function.
Signed-off-by: Guillaume Knispel <gknispel@proformatique.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

prevent miss categorising s2 as a type.  Fix up the spelling of the error
also.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

    #define pr_fmt(fmt)    "%s: " fmt, __func__

allow things with double quotes round them to avoid this check.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

  - More verbose help/usage message.
  - Make the option -f an alias for --file.
  - On -h, --help, and --version display help message and exit(0).
  - With no FILE(s) given, exit(1) with "no input files".
  - On invalid options display help/usage and exit(1).

Based on a patch by Pavel Machek.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

trying to determine relative indent of conditionals and their blocks.
Reported-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

the text after a C99 style comment the same way it does with block style
comments.  This prevents the text from getting processed as regular code.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

else.  This can trigger false modifier matching.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

This patch doesn't include mmc-regulator support
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Z11, as discussed on linux-mmc here: http://marc.info/?t=125017355000008Signed-off-by: Chris Ball <cjb@laptop.org>
Tested-by: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

#111: FILE: arch/arm/mach-at91/at91sam9260_devices.c:326:
+				at91_set_gpio_input(data->slot[i].detect_pin, 1);

ERROR: space required before the open parenthesis '('
#117: FILE: arch/arm/mach-at91/at91sam9260_devices.c:332:
+			switch(i) {

WARNING: line over 80 characters
#144: FILE: arch/arm/mach-at91/at91sam9260_devices.c:359:
+					"AT91: SD/MMC slot %d not available\n", i);

WARNING: line over 80 characters
#224: FILE: arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c:56:
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS

WARNING: line over 80 characters
#229: FILE: arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c:61:
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);

WARNING: line over 80 characters
#310: FILE: arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c:142:
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)

WARNING: line over 80 characters
#344: FILE: arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c:176:
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,

WARNING: line over 80 characters
#470: FILE: arch/arm/mach-at91/include/mach/board.h:78:
+extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);

total: 1 errors, 7 warnings, 422 lines checked

./patches/at91-atmel-mci-platform-configuration-to-the-the-atmel-mci-driver.patch has style problems, please review.  If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.

Please run checkpatch prior to sending patches

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

(board-sam9g20ek-2slot-mmc.c) and device support to make use of the
updated atmel-mci driver.

As the use of two slots modify GPIO pin allocation, we create another
board file.

This requires getting the most updated arch/arm/tools/mach-types from
http://www.arm.linux.org.uk/developer/machines/download.php to have the machine
type for the at91sam9g20ek-2slot-mmc board.

[nicolas.ferre@atmel.com: printk, slot_count modification in at91sam9260_devices.c file]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

interface.  The atmel-mci driver currently supports the AVR32 and this
patch adds AT91 support.

Add read/write proof selection switch dependent on chip availability of
this feature.

To use this new driver on a at91 the platform driver for your board needs
to be updated.

[nicolas.ferre@atmel.com indent, Kconfig comment and one printk modification]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Cc: <linux-mmc@vger.kernel.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

registers are prohibited.

To support embedded devices that require writes to SDIO function 0 outside
this range (e.g.  TI WL127x embedded sdio wifi device),
MMC_QUIRK_LENIENT_FN0 is introduced.

A card quirks field is added to `struct mmc_card' to support non-standard
devices (e.g.  embedded sdio devices).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

We specify clock-frequency manually, so that eSDHC will work without
upgrading U-Boot.  Though, that'll only work for default setup (1500 MHz)
on new board revisions.  For non-default setups, it's recommended to
upgrade U-Boot, since it will fixup clock-frequency automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

  exponential divisor calculation. The first if statement isn't correct
  at all, since it should check for "host->max_clk / pre_div / 16 >
  clock". The error doesn't cause any bugs because the check in the for
  loop does the right thing, and so the outer check becomes useless;

- For the linear divisor do the same: a single while statement is more
  readable than for + if construction;

- Add dev_dbg() that prints desired and actual clock frequency.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

hard-code the quirk.

Instead, look for "sdhci,wp-inverted" property, plus check for
mpc837x_{rdb,mds} machines since older device trees don't specify the new
property.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

sdhci-of driver will look for sdhci,wp-inverted properties to decide
whether apply a specific quirk.

So, document the property and add it to device tree source files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

  mmc0: error -110 whilst initialising SD card

That's because we calculate timeout value in a wrong way: on eSDHC hosts
the timeout clock is derivied from the SD clock, which is set dynamically.

As David Vrabel suggested, deriving timeout clock from SD clock is a
common scheme, so let's implement DATA_TIMEOUT_USES_SDCLK quirk and use it
for eSDHC hosts.

Also, from now on we don't need esdhc_get_timeout_clock() callback, so
remove it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

the eSDHC controllers don't have that bit, and that causes all sorts of
misbehaviour when using 4-bit mode capable SD cards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

1").  Before this patch the code didn't account that fact, so SD cards
were running underclocked.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

set_clock() callback is specified.

The patch should cause no functional changes, it just makes the code
self-documented and avoids any possible misuse of get_min_clock().
Suggested-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

operation is completed.  These commands are expected to always succeed
(otherwise the response would have indicated an error).

Set an arbitrarily large data timeout value (100ms) for these commands to
ensure that premature timeouts do not occur.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>