- 28 Aug, 2009 40 commits
-
-
Ivo van Doorn authored
Since patch "rt2x00: bss_info_changed() callback is allowed to sleep" the variable delayed wasn't used anymore. This means it can be removed along with the call to schedule_work which depended on that variable. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Gábor Stefanik authored
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable" functions, and use them during LP-PHY baseband init in b43. Signed-off-by:
Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by:
-
Gábor Stefanik authored
-Fix a few nasty typos (b43_phy_* operations instead of b43_radio_*) in the channel tune routines. -Fix some typos & spec errors found by MMIO tracing. -Optimize b43_phy_write & b43_phy_mask/set/maskset to use only the minimal number of MMIO accesses. (Write is possible using a single 32-bit MMIO write, while set/mask/maskset can be done in 3 16-bit MMIOs). -Set the default channel back to 1, as the bug forcing us to use channel 7 is now fixed. With this, the device comes up, scans, associates, transmits, receives, monitors and injects on all channels - in other words, it's fully functional. Sensitivity and TX power are still sub-optimal, due to the lack of calibration (that's next on my list). Signed-off-by:
-
Gábor Stefanik authored
The Qdiv roundup routine is essentially a fixed-point division algorithm, using only integer math. However, the version in the specs had a major error that has been recently fixed (a missing quotient++). Replace Qdiv roundup with a rewritten, simplified version. Signed-off-by:
-
Herton Ronaldo Krzesinski authored
This change implements rfkill support for RTL8187B and RTL8187L devices, using new cfg80211 rfkill API. Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Tested-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by:
Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by:
-
Herton Ronaldo Krzesinski authored
Larry Finger reports following lockdep warning: [ INFO: possible circular locking dependency detected ] 2.6.31-rc6-wl #201 ------------------------------------------------------- rfkill/30578 is trying to acquire lock: (&(&priv->work)->work#2){+.+...}, at: [<ffffffff81051215>] __cancel_work_timer+0xd9/0x222 but task is already holding lock: (&priv->conf_mutex#2){+.+.+.}, at: [<ffffffffa064a024>] rtl8187_stop+0x31/0x364 [rtl8187] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&priv->conf_mutex#2){+.+.+.}: [<ffffffff81065957>] __lock_acquire+0x12d0/0x1614 [<ffffffff81065d54>] lock_acquire+0xb9/0xdd [<ffffffff8127c32f>] mutex_lock_nested+0x56/0x2a8 [<ffffffffa064a392>] rtl8187_work+0x3b/0xf2 [rtl8187] [<ffffffff81050758>] worker_thread+0x1fa/0x30a [<ffffffff81054ca5>] kthread+0x8f/0x97 [<ffffffff8100cb7a>] child_rip+0xa/0x20 [<ffffffffffffffff>] 0xffffffffffffffff -> #0 (&(&priv->work)->work#2){+.+...}: [<ffffffff8106568c>] __lock_acquire+0x1005/0x1614 [<ffffffff81065d54>] lock_acquire+0xb9/0xdd [<ffffffff8105124e>] __cancel_work_timer+0x112/0x222 [<ffffffff8105136b>] cancel_delayed_work_sync+0xd/0xf [<ffffffffa064a33f>] rtl8187_stop+0x34c/0x364 [rtl8187] [<ffffffffa0242866>] ieee80211_stop_device+0x29/0x61 [mac80211] [<ffffffffa0239194>] ieee80211_stop+0x476/0x530 [mac80211] [<ffffffff8120ce15>] dev_close+0x8a/0xac [<ffffffffa01d9fa7>] cfg80211_rfkill_set_block+0x4a/0x7a [cfg80211] [<ffffffffa01bf4f0>] rfkill_set_block+0x84/0xd9 [rfkill] [<ffffffffa01bfc31>] rfkill_fop_write+0xda/0x124 [rfkill] [<ffffffff810cf286>] vfs_write+0xae/0x14a [<ffffffff810cf3e6>] sys_write+0x47/0x6e [<ffffffff8100ba6b>] system_call_fastpath+0x16/0x1b [<ffffffffffffffff>] 0xffffffffffffffff The problem here is that rtl8187_stop, while helding priv->conf_mutex, runs cancel_delayed_work_sync on an workqueue that runs rtl8187_work, which also takes priv->conf_mutex lock. Move cancel_delayed_work_sync out of rtl8187_stop priv->conf_mutex locking region. Reported-by: -
Vasanthakumar Thiagarajan authored
This patch adds 3-wire bluetooth coex support for AR9285. This support can be enabled through btcoex_enable modparam. Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
We don't need a hw cap bit for btcoex anymore as btcoex scheme type is enough to do this. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Also define macros for wlanactive and btactive (5 & 6) gpios. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Make sure btcoex register configured with appropriate values after it is initialized with the default values from initvals.h during reset. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
This function currently does initialization + enable the btcoex support. Split it into two logical functions which does the above operations separately. Btcoex initialization is done during attach time and enabling this feature is done in start(). Also, add code to disable btcoex support in stop(). Signed-off-by:
-
Jussi Kivilinna authored
rndis_wlan does not set cipher suites list for cfg80211 which causes wext-compat-range to report rndis_wlan not supporting WPA. Patch adds cipher suites list and fixes NetworkManager not being able to connect to WPA encrypted APs. Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
-
Sujith authored
When dumping register contents, HW has to be awake. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
PA Calibration is not needed for high power solutions. Signed-off-by:
-
Sujith authored
* First PA driver (PDPADRV1) was not powered down properly. * Compensation capacitor for dynamic PA was programmed incorrectly. Also, remove a stray REG_READ. Signed-off-by:
-
Sujith authored
PA calibration need not be done if the offset is not varying. The current logic does PA calibration even if the offset is the same. Signed-off-by:
-
John W. Linville authored
Initiate the conversion of libipw to the new cfg80211 configuration API. For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually migrate it to cfg80211 when the add/del/change_virtual_intf methods are implemented. Signed-off-by: -
Roel Kluin authored
Prevent a read of powInfo[-1] in the first iteration. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Jouni Malinen authored
When the queued management work items are processed in ieee80211_sta_work() an item could be removed. This could change the anybusy from true to false, so we better check whether we can start a new scan only after having processed the pending work first. Signed-off-by:
Jouni Malinen <jouni.malinen@atheros.com> Acked-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Johannes Berg authored
When an interface is taken down while a scan is pending -- i.e. a scan request was accepted but not yet acted upon due to other work being in progress -- we currently do not properly cancel that scan and end up getting stuck. Fix this by doing better checks when an interface is taken down. Signed-off-by:
-
Gábor Stefanik authored
The RC calibration code has some typos - fix them. Also, make the default channel 7, as channel 1 is still broken (only channels 7 and 8, and occasionally 9 work). Signed-off-by:
-
Jaswinder Singh Rajput authored
CC [M] drivers/net/wireless/prism54/islpci_eth.o drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_cleanup_transmit’: drivers/net/wireless/prism54/islpci_eth.c:53: warning: cast from pointer to integer of different size drivers/net/wireless/prism54/islpci_eth.c: In function ‘islpci_eth_receive’: drivers/net/wireless/prism54/islpci_eth.c:453: warning: cast from pointer to integer of different size Signed-off-by:
Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by:
-
Bob Copeland authored
Recent ath5k hardware is capable of doing CCMP acceleration. Enable it for the cards that support it. Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
-
Bob Copeland authored
Save a memcpy by just storing updates directly in the skb control block. Signed-off-by:
-
Marcos Chaparro authored
With this patch, a compaq c700 can turn on the wifi led. The array of compatible devices now includes the hardware present in this computer, as well as the led pin and polarity. Signed-off-by:
Marcos Chaparro <nitrousnrg@gmail.com> Signed-off-by:
-
Bob Copeland authored
The maze of if() statements in configure_filter is confusing. Reorganizing it as a switch statement makes it more apparent what is going on and reveals several suspicious settings. This has no functional changes, though it does remove some redundant flags that are set earlier. Also now that we can sleep, protect sc->filter_flags with the sc lock. Signed-off-by:
-
Arnd Hannemann authored
An integer overflow in the minstrel debug code prevented the throughput to be displayed correctly. This patch fixes that, by permutating operations like proposed by Pavel Roskin. Signed-off-by:
Arnd Hannemann <hannemann@nets.rwth-aachen.de> Signed-off-by:
-
Lennert Buytenhek authored
Only print the driver version once, and condense all per-PHY information to a single line. Signed-off-by:
Lennert Buytenhek <buytenh@marvell.com> Signed-off-by:
-
Lennert Buytenhek authored
Signed-off-by:
-
Lennert Buytenhek authored
Signed-off-by:
-
Lennert Buytenhek authored
Signed-off-by:
-
Johannes Berg authored
In mac80211's RX path some of the warnings that warn about drivers passing invalid status values leak the skb, fix that by refactoring the code. Signed-off-by:
-
Roel Kluin authored
Jump to out_err when the iftype is not supported. Signed-off-by:
-
Joerg Albert authored
Signed-off-by:
Joerg Albert <jal2@gmx.de> Acked-by:
Christian Lamparter <chunkeey@web.de> Signed-off-by:
-
Joerg Albert authored
Add beacon control by BSS_CHANGED_BEACON_ENABLED and bss_conf->enable_beacon from mac80211. Signed-off-by:
-
Reinette Chatre authored
Update MAINTAINERS file to reflect current maintenance status of ipw2x00 drivers. We remove James's name as he is not involved with this project anymore. We also update the Status to "Odd Fixes". This has been true for a while now, we have to make it official. There is also a new email address with which all relevant people can be reached. The same email address should be used for iwlwifi. Signed-off-by:
Reinette Chatre <reinette.chatre@intel.com> Cc: James Ketrenos <jketreno@linux.intel.com> Acked-by:
James Ketrenos <jketreno@linux.intel.com> Acked-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
