pxa2xx_i2s_resume is :
 - unconditionnaly setting SACR0_ENB
 - unsetting SACR0_ENB in saved SACR0 pxa_i2s.sacr0
fix these.

In pxa2xx_i2s_{resume,suspend}, save/restore registers even
when !dai->active.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

i2s_clk is 'put' for no reason in pxa2xx_i2s_shutdown.
Now we 'get' i2s_clk at probe and 'put' it at driver removal or when
probe fails.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

- hw_params enables both RPL and REC functions each time : Enable the
	appropriate function in pxa2xx_i2s_trigger.
- pxa2xx_i2s_shutdown disables i2s anytime one of RPL or REC function is
	off : Turn it off only when both functions are off.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we are in a know good state at end of probe :
Reset FIFO logic and registers, and make sure REC and RPL functions
along with FIFO service are disabled (SACR0_RST enables REC and RPL).

Resetting loses current settings so remove reset from stream startup.
Now reset occurs only at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There is a single I2S_SYNC pin on the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If the card was not instantiated in snd_soc_instantiate_card, calling
soc-remove will crash because some of codec, cpu_dai and card .remove
methods are called twice.
Fix this by returning from soc_remove immediately.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC uses the standard ALSA data format definitions to specify the wire
format used between the CPU and CODEC. Since the ALSA data formats all
include the endianess of the data but this information is not relevant
by the time the data has been encoded onto the serial link to the CODEC
this means that either all the CODEC drivers need to declare both big and
little endian variants or the core needs to fix up the format constraints
specified by CODEC drivers.

For now take the latter approach - this will need to be revisited if any
CODECs are endianness dependant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The file matches for PXA sound drivers missed the generic AC97 support
and were overly specific within sound/soc/pxa, omitting all machine
drivers and the SSP driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Replace the magic 0x80 value with a suitable macro definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The DAI structure has two pointers to the codec, one in the body of the
DAI and one in a union for a parent pointer.  Drop the parent pointer
version.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the ASoC side of the board support for the Crossbow
IMB400 daughter board.

Thanks to Crossbow for considerable assistance.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().

Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com

The regression was fixed by commit
3e5b5016, so no need to mark this
driver as BROKEN.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The defines for TDM and synchronous clocks are not used - they are
mostly a legacy of the automatic clocking configuration.  TDM will
require configuration of the number of timeslots and which ones to use
so can't be fit into the DAI format and synchronous mode is handled by
symmetric_rates (and needs to be done by constraints rather than when
the DAI format is being configured).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus.  Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.

Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Aids debugging.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.

At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This makes the interface usable with the s3c-iis-v2 rate calculator
and consistent with S3C2412.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>