- 23 May, 2009 15 commits
-
-
Mike Christie authored
bnx2i needs to be able to look up mgmt task like login and nop, because it does some processing of them on the completion path. This exports iscsi_itt_to_task so it can look up the task. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
If we could not allocate the initiator name or some other id like the hwaddress or netdev, then userspace could deal with the failure by just running in a dregraded mode. Now we want to be able to switch values for the params and we want some feedback, so this patch will check if a string like the initiatorname could not be allocated and return an error. Signed-off-by:
-
Mike Christie authored
bnx2i does not have one. It currently preallocates the bdt when the session is setup. We probably want to change that to a dma pool, then allocate from the pool in the alloc pdu. Until then check if there is a alloc pdu callout. Signed-off-by:
-
Mike Christie authored
When we create the tcp/ip connection by calling ep_connect, we currently just go by the routing table info. I think there are two problems with this. 1. Some drivers do not have access to a routing table. Some drivers like qla4xxx do not even know about other ports. 2. If you have two initiator ports on the same subnet, the user may have set things up so that session1 was supposed to be run through port1. and session2 was supposed to be run through port2. It looks like we could end with both sessions going through one of the ports. Fixes for cxgb3i from Karen Xie. Signed-off-by:
-
Zhenwen Xu authored
drivers/scsi/NCR_D700.c: In function `NCR_D700_probe': drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type Signed-off-by:
Zhenwen Xu <helight.xu@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Andy Yan authored
Using sticky field to improve retrieve performance by eliminating some lookups in . Remove some spurious casts. Signed-off-by:
Ying Chu <jasonchu@marvell.com> Signed-off-by:
Andy Yan <ayan@marvell.com> Signed-off-by:
Ke Wei <kewei@marvell.com> Signed-off-by:
-
Andy Yan authored
Utilize DECLARE_BITMAP to define the tags array. Signed-off-by:
-
Andy Yan authored
Null pointer check to avoid corruption. Signed-off-by:
-
Andy Yan authored
TMF task should be issued with Interrupt Disabled, or Deadlock may take place. Clean-up unused parameters and conditonal lock. Signed-off-by:
-
Andy Yan authored
Correct frame type setting according to parameter. Signed-off-by:
-
Kleber S. Souza authored
The ipr driver can hang if it encounters enough PCI errors to trigger the permanent error handler. The driver will attempt to initiate a "bringdown" of the adapter and fail all pending ops back. However, this bringdown is unlike any other bringdown of the adapter in the code as the driver. In this code path we end up failing back ops with allow_cmds still set to 1. This results in some commands, the HCAM commands in particular, getting immediately re-issued to the adapter on the done call, which results in an infinite loop in ipr_fail_all_ops. Fix this by setting allow_cmds to zero in this path. Signed-off-by:
Kleber S. Souza <klebers@linux.vnet.ibm.com> [brking@linux.vnet.ibm.com: alternate patch substituted] Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Eric Piel authored
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595 working when plugging it as a mass storage. Looking at SCSI option to get a phone behaving correctly was convoluted to say the least. There are quite a few other reports about USB card readers needing this option as well. This patch improves the help text to make the use of the option more obvious. Signed-off-by:
Eric Piel <eric.piel@tremplin-utc.net> Signed-off-by:
-
Roel Kluin authored
Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Acked by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Kai Makisara authored
This patch fixes the GCC 4.4 warning reported by David Binderman and Sergey Senozhatsky. The old version was working correctly but was not easy to read. Signed-off-by:
Kai Makisara <kai.makisara@kolumbus.fi> Signed-off-by:
-
Takahiro Yasui authored
scsi timeout on two or more devices may cause extremely long execution time for user applications because SDEV_OFFLINE state is changed to SDEV_RUNNING state during scsi error recovery procedures triggered by a bus reset or a host reset of scsi LLD, and scsi timeout can happens on the same devices many times. This happens because scsi_internal_device_unblock() changes device's state to SDEV_RUNNING even if a device in other states than SDEV_BLOCK, while the following two transitions are required in this function. SDEV_BLOCK -> SDEV_RUNNING SDEV_CREATED_BLOCK -> SDEV_CREATED Otherwise, it returns -EINVAL. Signed-off-by:
Takahiro Yasui <tyasui@redhat.com> [matthew@wil.cx: supplied rewritten base for patch] Signed-off-by:
Matthew Wilcox <matthew@wil.cx> Signed-off-by:
-
- 20 May, 2009 25 commits
-
-
Randy Dunlap authored
Fix function declarations: drivers/scsi/fcoe/fcoe.c:1356:28: warning: non-ANSI function declaration of function 'fcoe_dev_setup' drivers/scsi/libfc/fc_rport.c:1293:20: warning: non-ANSI function declaration of function 'fc_setup_rport' drivers/scsi/libfc/fc_rport.c:1302:23: warning: non-ANSI function declaration of function 'fc_destroy_rport' [jejb: fixed wrong doc in comment noticed during inspection] Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
FUJITA Tomonori authored
Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Kleber S. Souza authored
Marking the ipr clean up function ipr_remove() as __devexit and using __devexit_p() macro in its address reference. Signed-off-by:
Kleber Sacilotto de Souza <kleber@linux.vnet.ibm.com> Reported-by:
Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by:
-
Chauhan, Vijay authored
During device discovery read capacity fails with 0x020401 and sets the device size to 0. As a reason any I/O submitted to this path gets killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for 0x020401. NEED_RETRY in scsi_decide_disposition does not give sufficient time for the device to become ready. Signed-off-by:
Vijay Chauhan <vijay.chauhan@lsi.com> Signed-off-by:
-
Aaro Koskinen authored
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References to the destroyed LCB are cleared from the target structure (instead of leaving a dangling pointer), and when the last LCB for the target is destroyed the reference to the upper layer target data is cleared. The host lock is used to prevent a race with the interrupt handler. Also user commands are prevented for targets with all LCBs destroyed. Signed-off-by:
Aaro Koskinen <Aaro.Koskinen@nokia.com> Tested-by:
Tony Battersby <tonyb@cybernetics.com> Signed-off-by:
-
Aaro Koskinen authored
(Resent with proper formatting) Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after a bus reset (a failed clear can trigger a bus reset and it should not be attemped again after that). Signed-off-by:
-
Michael Reed authored
The driver now waits for the scsi commands associated with a particular error recovery step to be returned to the mid-layer, and returns the appropriate SUCCESS or FAILED status. Removes unneeded polling of chip for interrupts. This patch also bumps the driver version number. Signed-off-by:
Michael Reed <mdr@sgi.com> Signed-off-by:
-
Michael Reed authored
Remove some unneeded, inactive and unused code, make some trivial corrections to comments and a printk, and return a proper status in qla1280_queuecommand. No fundamental logic changes are made. Signed-off-by:
-
Alan Stern authored
This patch (as1224) changes the default timeout for INQUIRY commands from 3 seconds to 20 seconds, which is the value used by Windows for USB Mass-Storage devices. Some of these devices, like the Corsair Flash Voyager (see Bugzilla #12188) really do need a long timeout. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Andy Yan authored
This version contains following main changes - Switch to new layout to support more types of ASIC. - SSP TMF supported and related Error Handing enhanced. - Support flash feature with delay 2*HZ when PHY changed. - Support Marvell 94xx series ASIC for 6G SAS/SATA, which has 2 88SE64xx chips but any different register description. - Support SPI flash for HBA-related configuration info. - Other patch enhanced from kernel side such as increasing PHY type [jejb: fold back in DMA_BIT_MASK changes] Signed-off-by:
Jeff Garzik <jgarzik@redhat.com> Signed-off-by:
-
Jeff Garzik authored
Split mvsas driver into multiple source codes, based on the split and function distribution found in Marvell's mvsas update. Signed-off-by:
-
Jeff Garzik authored
Zero functional changes, just file movement. This commit prepares for the upcoming integration of the Marvell-provided driver update that splits the driver into support for both 64xx and 94xx chip families. Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Anirban Chakraborty authored
Read adapter's physical port number from interrupt pin register and use it instead of pci function number to offset into the nvram to obtain the port's configuration parameters. Signed-off-by:
Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
As it may be useful during debugging to use a specific firmware image. Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
Michael Reed authored
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth) isn't sticky when the device is connected via a QLogic fibre channel adapter. The QLogic qla2xxx fibre channel driver dynamically adjusts a lun's queue depth. If a user has a specific need to limit the number of commands issued to a lun (say a tape drive, or a shared raid where the total commands issued to all luns is limited at the controller level, for example) and writes a limiting value to /sys/block/sdXX/device/queue_depth, the qla2xxx driver will silently and gradually increase the queue depth back to the driver limit of ql2xmaxqdepth. While reducing this value (module parameter) or increasing the interval between ramp ups (ql2xqfullrampup) offers the potential for a work around it would be better to have the option of just disabling the dynamic adjustment of queue depth. This patch implements an "off switch" as a module parameter. Signed-off-by:
-
Joe Carnuccio authored
Set the conditional plogi option bit whenever logging in the fabric management server (if it is already logged in, it does not need an explicit login; an implicit login suffices). Signed-off-by:
-
Andrew Vasquez authored
Information present in static table is only valid for pre-ISP25xx adapters. Signed-off-by:
-
Harish Zunjarrao authored
Signed-off-by:
Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
Anirban Chakraborty authored
srbs used to maintain a reference to the request queue on which it was enqueued. This is no longer required as the request queue pointer is now maintained in the scsi host that issues the srb. Signed-off-by:
-
Anirban Chakraborty authored
Set the module parameter ql2xmultique_tag to 1 to enable this feature. In this mode, the total number of response queues created is equal to the number of online cpus. Turning the block layer's rq_affinity mode on enables requests to be routed to the proper cpu and at the same time it enables completion of the IO in a response queue that is affined to the cpu in the request path. Signed-off-by:
-
Anirban Chakraborty authored
Set the number of request queues to the module paramater ql2xmaxqueues. Each vport gets a request queue. The QoS value set to the request queues determines priority control for queued IOs. If QoS value is not specified, the vports use the default queue 0. Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
