Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.

Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.

Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.

Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)

I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.

Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unlike ifconfig, iproute doesn't report an error when setting
an interface up fails:

(example: put wireless network mac80211 interface into repeater mode
with iwconfig but do not set a peer MAC address, it should fail with
-ENOLINK)

without patch:
# ip link set wlan0 up ; echo $?
0
# 

with patch:
# ip link set wlan0 up ; echo $?
RTNETLINK answers: Link has been severed
2
# 

Propagate the return value from dev_change_flags() to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit a144ea4b [IPV4]: annotate struct in_ifaddr

Missed this extra byteswap as the isdn inlines hide the htonl inside
put_u32 which causes an extra byteswap on little-endian arches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2
http://marc.info/?l=e1000-devel&m=121365543823387&w=2

This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).

Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol().  Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol().  Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol().  Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joey Zhuo <joeyzhuo@via.com.tw>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 46abc021 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.

The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.

Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet.  Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory.  Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.

Fixes the following oops:

root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault

p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This is the next page of the scm recursion story (the commit 
f8d570a4 net: Fix recursive descent in __scm_destroy()).

In function scm_fp_dup(), the INIT_LIST_HEAD(&fpl->list) of newly
created fpl is done *before* the subsequent memcpy from the old 
structure and thus the freshly initialized list is overwritten.

But that's OK, since this initialization is not required at all,
since the fpl->list is list_add-ed at the destruction time in any
case (and is unused in other code), so I propose to drop both
initializations, rather than moving it after the memcpy.

Please, correct me if I miss something significant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver is pretty mature, and the worst of the known
problems has been fixed (the 32-bit failures due to readq
implementation).

So let's finally give it a version of 1.0
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix this warning:

  net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
  net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used

this is a lockdep macro problem in the !LOCKDEP case.

We cannot convert it to an inline because the macro works on multiple types,
but we can mark the parameter used.

[ also clean up a misaligned tab in sock_lock_init_class_and_name() ]

[ also remove #ifdefs from around af_family_clock_key strings - which
  were certainly added to get rid of the ugly build warnings. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make 9p's RDMA option depend on INET since it uses Infiniband rdma_*
functions and that code depends on INET.  Otherwise 9p can try to
use symbols which don't exist.

ERROR: "rdma_destroy_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_connect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_id" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_create_qp" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_route" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_disconnect" [net/9p/9pnet_rdma.ko] undefined!
ERROR: "rdma_resolve_addr" [net/9p/9pnet_rdma.ko] undefined!

I used an if/endif block so that the menu items would remain
presented together.

Also correct an article adjective.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Failure to pass netns_ok check is SILENT, except some MIB counter is
incremented somewhere.

And adding "netns_ok = 1" (after long head-scratching session) is
usually the last step in making some protocol netns-ready...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes two bugs:

1. setsockopt() of anything but a Type 2 routing header should return
EINVAL instead of EPERM.  Noticed by Shan Wei
(shanwei@cn.fujitsu.com).

2. setsockopt()/sendmsg() of a Type 2 routing header with invalid
length or segments should return EINVAL.  These values are statically
fixed in RFC 3775, unlike the variable Type 0 was.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix bnx2 so that netpoll works properly.  Specifically:

1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device

2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a TX hang reported by Jesper Dangaard Brouer.

When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own.  This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.

In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first.  There could be side effects, and in fact that is
exactly the problem here.

The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits.  A read clears the state
bits.

We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.

Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device.  Unfortunately, that trick no longer
works...

Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run.  Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.

(Above text by me.  Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In __sock_recv_timestamp() the additional SCM_TIMESTAMP[NS] is used. This
has the same value as SO_TIMESTAMP[NS], so this is a purely cosmetic change.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a minor bug in tcp_htcp.c which has been
highlighted by Lachlan Andrew and Lawrence Stewart.  Currently, the
time since the last congestion event, which is stored in variable
last_cong, is reset whenever there is a state change into
TCP_CA_Open.  This includes transitions of the type
TCP_CA_Open->TCP_CA_Disorder->TCP_CA_Open which are not associated
with backoff of cwnd.  The patch changes last_cong to be updated
only on transitions into TCP_CA_Open that occur after experiencing
the congestion-related states TCP_CA_Loss, TCP_CA_Recovery,
TCP_CA_CWR.
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>