AT91SAM9260 stopped booting with the recent changes to MM
initialisation - it was asking for a non-aligned virtual address
which caused loops to be non-terminal.  Fix this by rounding
virtual addresses down, but remember to include the offset in
the length, and round the length up to the following page.

This means that asking for a mapping of 4K starting at 2K into
a page maps two pages as one would expect.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARM Versatile PCI config reads of one byte width have the lowest two
bits of the address cleared and result in reading from a wrong place
in the config space.  This change is to use word size accesses like it is done for halfword reads.

Byte reads are used for retrieving the IRQ number of a PCI device and the problem was not exposed until 2.6.20 because the value read was discarded in drivers/pci/setup-irq.c (recently fixed).
Signed-off-by: Andrzej Zaborowski <andrew@openedhand.com>
Acked-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Last -rc? That's the plan..

Commit 52ade9b3 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues.  Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.

at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices.  However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose.  Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.

This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls.  It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Don't use PNP detection by default yet.  We have some PNP and BIOS issues
to work out first.

Sample problem on a Toshiba Portege 4000: the SMCf010 device is handed off
disabled.  We assign I/O ports originally assigned to the SMCf010 to a
PCMCIA device instead.  We enable the SMCf010, configuring it to use
disjoint ports, but _SRS doesn't work correctly, so the device doesn't
work.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3ebad590 ("[PATCH] x86: Save and
restore the fixed-range MTRRs of the BSP when suspending") added mtrr
operations without verifying that the CPU has MTRRs.  Crashes transmeta
CPUs.

Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux@horizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If asus_acpi_init doesn't find any device it knows about, it mistakenly
returns a "success" error code even though it cleans up after itself.  Later
when trying to rmmod asus_acpi, the module_exit routine would try to clean up
one more time and we would end up calling
acpi_bus_unregister_driver(&asus_hotk_driver) twice.  This patch addresses
this first problem by returning -ENODEV when no appropriate device is found.

Then there was also another bug with the code handling the return value of
backlight_device_register.  If this function ever failed, the driver would
cleanup by calling the module_exit routine from module_init, but it would
still return "success".  So any attempt to rmmod this module would result in
asus_acpi_exit being called twice but it's not ready to handle it (I haven't
hit this bug, just found it by code inspection).  This patch fixes that by
inserting a return -ENODEV; at the end of this error handling path.
Signed-off-by: Maxime Austruy <maxime@tralhalla.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Provide stubs for more PCI bus/slot functions when CONFIG_PCI=n.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix section mismatch warnings:

WARNING: sound/built-in.o(.exit.text+0x3ad): Section mismatch: reference to .init.text: (between 'sb_exit' and 'unload_uart6850')
WARNING: sound/built-in.o(.exit.text+0x753): Section mismatch: reference to .init.text: (between 'snd_mts64_module_exit' and 'snd_portman_module_exit')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/home/rpjday/AMD/k/topics/0_hi/hi1.c:15: error: dereferencing pointer to incomplete type
/home/rpjday/AMD/k/topics/0_hi/hi1.c:16: error: dereferencing pointer to incomplete type
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We agreed to remove the WARN_ON_ONCE before 2.6.22 is released.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The blink driver wakes up every jiffies which wastes power unnecessarily.
Using a notifier gives same effect. Also add ability to unload module.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
[ We should really just delete the whole thing. The blink driver is
  broken in many other ways too  -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 9215da33 "fixed" the MTRR range
check to not allow any MTRR's under the 1MB mark (since that's where the
fixed MTRR's are active).

However, that was totally bogus, since it's normal (and almost required)
to have a large variable MTRR that starts at 0, and covers some large
percentage of the whole RAM, and then using the fixed MTRR's to override
that large MTRR to handle the special ISA hole in the 640k-1M region.

The old check was bogus too (checking that no variable MTRR is used that
is entirely under the 1MB range), but at least it wasn't actively
detrimental, because no sane situation would ever trigger such MTRR
usage in the first place.

That said, the whole notion of not allowing variable MTRR's in the low
1MB is just stupid, so rather than revert the commit, this just removes
the whole sad and unnecessary check entirely.

Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Luca Palermo <darkmage@sabayonlinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Add linux/pagemap.h to asm/tlb.h
  [SPARC64]: Need to set state to IDLE during sun4v IRQ enable.
  [SPARC64]: Fix VIRQ enabling.
  [SPARC64]: Add irqs to mdesc_node.

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IRDA]: fix printk format
  [NETPOLL] netconsole: fix soft lockup when removing module
  [NETPOLL]: tx lock deadlock fix
  SCTP: lock_sock_nested in sctp_sock_migrate
  SCTP: Fix sctp_getsockopt_get_peer_addrs
  SCTP: update sctp_getsockopt helpers to allow oversized buffers

The vdso64 portion of patch 74609f45 for
fixing problems with NULL gettimeofday input mistakenly checks for a
null tz field twice, when it should be checking for null tz once, and
null tv once; by way of a r10/r11 typo.

Any application calling gettimeofday(&tv,NULL) will "fail".

This corrects that typo, and makes my G5 happy.

Tested on G5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Forwarded-by: Ben Herrenschmidt <benh@kernel.crashing.org>

[ Ben says: "I checked the 32 bits part of the change is correct.  You
  can probably blame me for originally writing the 2 versions with
  inversed usage of r10 and r11, thus confusing Tony :-)"

  Ben duly blamed.   - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix printk format warning:
drivers/net/irda/irport.c:512: warning: format '%d' expects type 'int', but argument 5 has type 'long int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

#1
Until kernel ver. 2.6.21 (including) cancel_rearming_delayed_work()
required a work function should always (unconditionally) rearm with
delay > 0 - otherwise it would endlessly loop. This patch replaces
this function with cancel_delayed_work(). Later kernel versions don't
require this, so here it's only for uniformity.

#2
After deleting a timer in cancel_[rearming_]delayed_work() there could
stay a last skb queued in npinfo->txq causing a memory leak after
kfree(npinfo).

Initial patch & testing by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As seen on sparc64-allnoconfig:

  CC      arch/sparc64/mm/tlb.o
In file included from arch/sparc64/mm/tlb.c:19:
include/asm/tlb.h: In function 'tlb_flush_mmu':
include/asm/tlb.h:60: warning: implicit declaration of function 'release_pages'
include/asm/tlb.h: In function 'tlb_remove_page':
include/asm/tlb.h:92: warning: implicit declaration of function 'page_cache_release'
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for_linus' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc:
  phy: Fix phy_id for Vitesse 824x PHY

Not all the world is an i386.  Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer.  Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.

Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely.  In fact, ARM already had that, but called it
sys_arm_sync_file_range.  Move it to fs/sync.c and rename it, then implement
the needed compatibility routine.  And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.

Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The interrupt clearing code in mpsc_sdma_intr_ack() mistakenly clears the
interrupt for both controllers instead of just the one its supposed to.
This can result in the other controller appearing to hang because its
interrupt was effectively lost.

So, don't clear the interrupt cause bits for both MPSC controllers when
clearing the interrupt for one of them.  Just clear the one that is
supposed to be cleared.
Signed-off-by: Jay Lubomirski <jaylubo@motorola.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gcc correctly says

fs/ext2/super.c: In function 'ext2_remount':
fs/ext2/super.c:1055: warning: 'err' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/mips/jazz/setup.c:55:4: error: Initializer entry defined twice
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This can disrupt userspace signal management.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When I use relayfs with "overwrite" mode, read() still sets incorrect
number of consumed bytes.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Tom Zanussi <zanussi@us.ibm.com>
Acked-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a bug in the relay read interface causing the number of consumed bytes
to be set incorrectly.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change __devexit to __devexit_p:
sound/isa/opl3sa2.c:956: error: expected expression before '__attribute__'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Also, remove outdated 1394 tree and mention MAINTAINERS as pointer to
development trees.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

WARNING: drivers/built-in.o(.text+0x8742a): Section mismatch: reference to .init.data:chipsfb_fix (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x87432): Section mismatch: reference to .init.data:chipsfb_fix (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x87442): Section mismatch: reference to .init.data:chipsfb_var (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x8744a): Section mismatch: reference to .init.data:chipsfb_var (between 'chipsfb_pci_init' and 'chipsfb_set_par')

init_chips is only called from chipsfb_pci_init
chipsfb_fix and chipsfb_var are only referenced from init_chips
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The new code in kernel/signal.c does not allow fetching private signals
from another task.  This patch avoid spurious POLLIN returns from a
signalfd poll(2) operation.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch changes the test for the thread pid from >= 0 to > 0.

When the saa8134 driver initialization fails after a certain point, it goes
through the complete shutdown process for the driver.  Part of shutting it
down includes tearing down the thread for tv audio.

The test for tearing down the thread tests for >= 0.  Since the dev
structure is kzalloc'd, the test will always be true if we haven't tried to
start the thread yet.  We end up waiting on pid 0 to complete, which will
never happen, so we lock up.

This bug was observed in Novell Bugzilla 284718, when request_irq() failed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cannot mix const and __initdata:
sound/pci/ice1712/prodigy192.c:708: error: ak4114_controls causes a section type conflict
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Rename struct pci_driver data so that false section mismatch warnings won't
be produced.

Sam, ISTM that depending on variable names is the weakest & worst part of
modpost section checking.  Should __init_refok work here?  I got build
errors when I tried to use it, probably because the struct pci_driver probe
and remove methods are not marked "__init_refok".

WARNING: drivers/dma/ioatdma.o(.data+0x10): Section mismatch: reference to .init.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
WARNING: drivers/dma/ioatdma.o(.data+0x14): Section mismatch: reference to .exit.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Chris Leech <christopher.leech@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If one has a dependency chain (tristate)FOO depends on (bool)BAR depends on
(tristate)BAZ, build problems will result.  If BAZ=m, then BAR can be set
y, which allows FOO=y.  It's possible to have FOO=y && BAZ=m, which
wouldn't be allowed if FOO depended directly on BAZ.  In effect, the bool
promotes the tristate from m to y.

This ends up causing a problem with several menuconfigs that look like:

menuconfig BAR
	bool
	depends on BAZ [tristate]
if BAR
config FOO
	tristate
endif

The solution used here is to add the dependencies of BAR to the if
statement, so that items in the if block will gain a direct
non-bool-promoted dependency on BAZ.  This is how it would work if a menu
was used instead of an if block.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

validate_anon_vma gave a useful check on the integrity of the anon_vma list
when Andrea was developing obj rmap; but it was not enabled in SLES9
itself, nor in mainline, until Nick changed commented-out RMAP_DEBUG to
configurable CONFIG_DEBUG_VM in 2.6.17.  Now Petr Vandrovec reports that
its BUG_ON(mapcount > 100000) can easily crash a CONFIG_DEBUG_VM=y system.

That limit was just an arbitrary number to protect against an infinite
loop.  We could raise it to something enormous (depending on sizeof struct
vma and size of memory?); but I rather think validate_anon_vma has outlived
its usefulness, and is better just removed - which gives a magnificent
performance boost to anything like Petr's test program ;)

Of course, a very long anon_vma list is bad news for preemption latency,
and I believe there has been one recent report of such: let's not forget
that, but validate_anon_vma only makes it worse not better.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Petr Vandrovec <petr@vmware.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: Andrea Arcangeli <andrea@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some HP firmware leaves the SMCf010 IRDA device incompletely configured, or
reports the wrong resources in _CRS.  As a workaround, when we find such a
device, try to auto-configure the device.

This ignores the _CRS data, picks a config from _PRS, and runs _SRS to
configure the device.  This makes smsc-ircc2 work correctly with PNP
resources (with no preconfiguration!) on all the machines I tested.

I think Windows does something like this by default for all devices,
so we should consider doing the same thing in Linux.

This patch addresses part of the 2.6.22 regression:
    "no irda0 interface (2.6.21 was OK), smsc does not find chip"
It fixes smsc-ircc2 PNP device detection on HP nc6000, nc6220, nw8000,
nw8240, and possibly other machines.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If we rely on the device resources from PNPBIOS, we also have to rely on
the BIOS to configure any bridges on the way to the device.

Using the PNPBIOS resources but changing the configuration of a bridge
behind the back of the firmware is likely to make things inconsistent.

This patch addresses part of the 2.6.22 regression:
    "no irda0 interface (2.6.21 was OK), smsc does not find chip"
It fixes smsc-ircc2 PNP device detection on HP nx5000 laptops.
Other laptops, including HP nc6000, HP nc8000, HP nw8000, and Toshiba
Portege 4000, still need PNP quirks to make this work.

With "smsc-ircc2.nopnp", we do the legacy device probe, including manual
bridge preconfiguration, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Acked-by: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>