Create vio_bus_ops so that we just pass a structure to vio_bus_init
instead of three separate function pointers.

Rearrange vio.h to avoid forward references. vio.h only needs
struct device_node from prom.h so remove the include and just
declare it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Take some assignments out of vio_register_device_common and
rename it to vio_register_device.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Formatting changes to vio.c to bring it closer to the
kernel coding standard.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

gcc 3.4 (at least the build we are using) puts the gcc generated .ident
string into a .note section at the end of the files it compiles (gcc
3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section).  This
means that the lparmap.s file we produce in the iSeries build may end with
a .note section.  When we include it into head.S, the assembler can no
longer resolve some of the conditional branches since the target label
ends up too far away.  This patch just forces us back to the .text section
after including lparmap.s.

The breakage was caused by my patch "iSeries build with newer assemblers
and compilers" (sha1-id: 2ad56496).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

A mistake rebasing the series of ppc64 head.S cleanup patches meant
the #include of lparmap.s, needed for iSeries was lost.  This patch
puts it back again.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

With CONFIG_HUGETLB_PAGE=n:

In file included from kernel/sysctl.c:37:
include/linux/hugetlb.h:104:1: warning: "hugetlb_free_pgd_range" redefined
In file included from include/linux/mm.h:36,
                 from kernel/sysctl.c:23:
include/asm/pgtable.h:492:1: warning: this is the location of the previous definition
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

It appears that a memory barrier soon after a mispredicted
branch, not just in the delay slot, can cause the hang
condition of this cpu errata.

So move them out-of-line, and explicitly put them into
a "branch always, predict taken" delay slot which should
fully kill this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>

When the spinlock routines were moved out of line into
kernel/spinlock.c this made it so that the debugging
spinlocks record lock acquisition program counts in the
kernel/spinlock.c functions not in their callers.
This makes the debugging info kind of useless.

So record the correct caller's program counter and
now this feature is useful once more.
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed sparc architecture specific users of asm/segment.h and
asm-sparc/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed sparc64 architecture specific users of asm/segment.h and
asm-sparc64/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current uncorrectable error handling was poor enough
that the processor could just loop taking the same
trap over and over again.  Fix things up so that we
at least get a log message and perhaps even some register
state.

In the process, much consolidation became possible,
particularly with the correctable error handler.

Prefix assembler and C function names with "spitfire"
to indicate that these are for Ultra-I/II/IIi/IIe only.

More work is needed to make these routines robust and
featureful to the level of the Ultra-III error handlers.
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify we really are taking a data access exception trap, at TL1, from
one of the window spill/fill handlers.

Else call a new function, data_access_exception_tl1, to log the error.
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Read ASI_IMMU SFSR not ASI_DMMU.
2) IMMU has no SFAR, read TPC instead
3) Delete old and incorrect comment about the DTLB protection
   trap having a dependency on the SFSR contents in order to
   function correctly
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

 * ieee1394_device_id has kernel_ulong_t field after an odd number of
   __u32 ones.  Since mod_devicetable.h is included both from kernel and
   from host build helper, we may be in trouble if we are building on
   32bit host for 64bit target - userland sees unsigned long long,
   kernel sees unsigned long and while their sizes match, alignments
   might not.  Fixed by forcing alignment.  Fortunately, almost nobody
   else needs that - the rest of such fields is naturally aligned as it
   is.

 * of_device_id has void * in it.  Host userland helpers need
   kernel_ulong_t instead, since their void * might have nothing to do
   with the kernel one.  Fixed in the same way it's done for similar
   problems in pcmcia_device_id (ifdef __KERNEL__).

 * pcmcia_device_id has the same problem as ieee1394_device_id.  Fixed
   the same way.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We've had Woozy Numbat for a while now.  Here's an updated name care of
Jeff Garzik and myself.
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it.  I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.

The way NODEFER affects signals on other Unix boxes is as follows:

1) If NODEFER is set, other signals in sa_mask are still blocked.

2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).

The way NODEFER affects signals on Linux:

1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).

2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.

The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.

Unix boxes that were tested:  DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.

* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux.  So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Paulus, I think this is now a reasonable candidate for the post-2.6.13
queue.

Relax address restrictions for hugepages on ppc64

Presently, 64-bit applications on ppc64 may only use hugepages in the
address region from 1-1.5T.  Furthermore, if hugepages are enabled in
the kernel config, they may only use hugepages and never normal pages
in this area.  This patch relaxes this restriction, allowing any
address to be used with hugepages, but with a 1TB granularity.  That
is if you map a hugepage anywhere in the region 1TB-2TB, that entire
area will be reserved exclusively for hugepages for the remainder of
the process's lifetime.  This works analagously to hugepages in 32-bit
applications, where hugepages can be mapped anywhere, but with 256MB
(mmu segment) granularity.

This patch applies on top of the four level pagetable patch
(http://patchwork.ozlabs.org/linuxppc64/patch?id=1936).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

You can't call get_property() on a NULL node, so check if of_chosen is set
in check_for_initrd().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>

 arch/ppc64/kernel/setup.c |   20 ++++++++++++--------
 1 files changed, 12 insertions(+), 8 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>

unflatten_device_tree() doesn't check if lmb_alloc() succeeds or not, it
should. All it can do is panic, but at least there's an error message
(assuming you have some sort of console at that point).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>

 arch/ppc64/kernel/prom.c |    9 +++++++--
 1 files changed, 7 insertions(+), 2 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>

When unflatten_dt_node() fails to find an OF_DT_END_NODE tag it prints
"Weird tag at start of node", this should be "Weird tag at end of node".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>

 arch/ppc64/kernel/prom.c |    2 +-
 1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch moves power4_enable_pmcs() to arch/ppc64/kernel/pmc.c.

I've tested it on P5 LPAR and P4. It does what it used to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If both CONFIG_XMON and CONFIG_XMON_DEFAULT is enabled in the .config,
there is no way to disable xmon again. setup_system calls first xmon_init,
later parse_early_param. So a new 'xmon=off' cmdline option will do the right
thing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

We can now remove CONFIG_MSCHUNKS as it doesn't do anything interesting
anymore.

The only macro in abs_addr.h which is called by non-iSeries code is
phys_to_abs(), so remove the other dummy implementations, and we add a
firmware feature check to phys_to_abs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

lmb_phys_mem_size() can always return lmb.memory.size, as long as it's called
after lmb_analyze(), which it is. There's no need to recalculate the size on
every call.

lmb_analyze() was calculating a few things we then threw away, so just don't
calculate them to start with.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

We no longer need the lmb code to know about abs and phys addresses, so
remove the physbase variable from the lmb_property struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

abs_to_phys() is a macro that turns out to do nothing, and also has the
unfortunate property that it's not the inverse of phys_to_abs() on iSeries.

The following is for my benefit as much as everyone else.

With CONFIG_MSCHUNKS enabled, the lmb code is changed such that it keeps
a physbase variable for each lmb region. This is used to take the possibly
discontiguous lmb regions and present them as a contiguous address space
beginning from zero.

In this context each lmb region's base address is its "absolute" base
address, and its physbase is it's "physical" address (from Linux's point of
view). The abs_to_phys() macro does the mapping from "absolute" to "physical".

Note: This is not related to the iSeries mapping of physical to absolute
(ie. Hypervisor) addresses which is maintained with the msChunks structure.
And the msChunks structure is not controlled via CONFIG_MSCHUNKS.

Once upon a time you could compile for non-iSeries with CONFIG_MSCHUNKS
enabled. But these days CONFIG_MSCHUNKS depends on CONFIG_PPC_ISERIES, so
for non-iSeries code abs_to_phys() is a no-op.

On iSeries we always have one lmb region which spans from 0 to
systemcfg->physicalMemorySize (arch/ppc64/kernel/iSeries_setup.c line 383).
This region has a base (ie. absolute) address of 0, and a physbase address
of 0 (as calculated in lmb_analyze() (arch/ppc64/kernel/lmb.c line 144)).

On iSeries, abs_to_phys(aa) is defined as lmb_abs_to_phys(aa), which finds
the lmb region containing aa (and there's only one, ie. 0), and then does:

 return lmb.memory.region[0].physbase + (aa - lmb.memory.region[0].base)

physbase == base == 0, so you're left with "return aa".

So remove abs_to_phys(), and lmb_abs_to_phys() which is the implementation
of abs_to_phys() for iSeries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The lmb code is all written to use a pointer to an lmb struct. But it's always
the same lmb struct, called "lmb". So we take the address of lmb, call it
_lmb and then start using _lmb->foo everywhere, which is silly.

This patch removes the _lmb pointers and replaces them with direct references
to the one "lmb" struct. We do the same for some _mem and _rsv pointers which
point to lmb.memory and lmb.reserved respectively.

This patch looks quite busy, but it's basically just:
s/_lmb->/lmb./g
s/_mem->/lmb.memory./g
s/_rsv->/lmb.reserved./g
s/_rsv/&lmb.reserved/g
s/mem->/lmb.memory./g
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>