GPIO and MPUIO wake updates:

 - Hook MPUIOs into the irq wakeup framework too.  This uses a platform
   device to update irq enables during system sleep states, instead of
   a sys_device, since the latter is no longer needed for such things.

 - Also forward enable/disable irq wake requests to the relevant GPIO
   controller, so the top level IRQ dispatcher can (eventually) handle
   these wakeup events automatically if more than one GPIO pin needs to
   be a wakeup event source.

 - Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
   read-only data under the spinlock.

This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.

Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong:  omap1
saves the flags but ignores them, omap2 doesn't even save it.  (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Replace OMAP1610 to OMAP2420.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function.  On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods.  Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Wait a fixed amount of time between writing to the columns
register and reading rows state to allow the keypad to respond
on Palm Tungsten E and Zire 71.  The value for Zire 71 keypad
was tested by Marek Vasut.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables I2C-2 support for 2430 SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch makes minor changes in palmz71 board file (formating changes) and
renames one GPIO (PALMZ71_PINTDAV_GPIO to PALMZ71_PENIRQ_GPIO) in
board-palmz71.h and board-palmz71.c .
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

H4 has two peripheral ports, one for "download" and one for OTG.
The one to use is selected through Kconfig.

NOTE:  not yet working; I suspect there's a clock still turned off
or something like that, since neither port responds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Additional cleanup for debug boards on H2/P2/H3/H4:  move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices).  Make H4 use that.

This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.

It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.

In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO).  Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix typo in gpio
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is one extra brace in z71 board file, this patch fixes it.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Fri, Oct 27, 2006 at 05:16:59PM +0100, Jonathan McDowell wrote:
> However having prodded further I'm seeing incorrect key parsing with
> the omap-keypad driver under both -rc2 and -rc3 (works fine in
> 2.6.18-omap1). Numerous keys now returns strings of characters rather
> than the single expected character. A few keys still work as expected
> however. Before I dig in further is anyone else seeing anything similar?

This appears to be due to the addition of keymapsize to the
omap_kp_platform_data structure. The patch below fixes things up for
the Delta; other boards appear to have already had this done.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

More GPIO/IRQ cleanup:

  - compile-time removal of much useless code
      * mpuio support on non-OMAP1.
      * 15xx/730/24xx gpio support on 1610
      * 15xx/730/16xx gpio support on 24xx
      * etc

  - remove all BUG() calls, which are always bad news ... replaced some
    with normal fault reports for that call, others with WARN_ON(1).

  - small mpuio bugfix:  add missing set_type() method

Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Minor GPIO cleanups:  remove needless #include, and omap_gpio_init()
should be __init, as well as all the board init code calling it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.

If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmz71 specific things - board file.
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables some clock on omap310.
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPMC updates:
 - bugfixes: wrong/missing flags, omitted write, wrong test
 - don't map memory segments starting at zero
 - improve debug messaging
 - export gpmc_get_fclk_perio]d() since it's needed to calc timings
 - expect gpmc_cs_set_timings() caller to have initialized sync vs async

Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some OMAP 24xx pin mux declarations to support:

 - TUSB 6010 EVM (on H4)
 - All three full speed USB ports
 - GPIOs used with USB0 on Apollon and H4

For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove some conflicting declarations in omap2/memory.c so that the
file builds again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some GPIO debug support:  /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.

Includes minor bugfixes:  recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In previous GPMC patch, there was a typo. Fix typo and add header files for
set_irq_type() warnings.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable serial idling and wakeup features
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Useful for debugging power management code.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable 24xx GPIO autoidling
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add DMA IRQ sanity checks
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Place SMS and SDRC into smart idle mode
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix warning:

arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix the following compiler warning (only visible with
CONFIG_OMAP_RESET_CLOCKS):

arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since d9a9cdfb <linux/sysfs.h> is using
ENOSYS without including <linux/errno.h> if CONFIG_SYSFS is disabled.

Fixed by including <linux/errno.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>