People were complaining about broken balancing with the recent -rt
series.

A look at /proc/sched_debug yielded:

cpu#0, 2393.874 MHz
  .nr_running                    : 0
  .load                          : 0
  .cpu_load[0]                   : 177522
  .cpu_load[1]                   : 177522
  .cpu_load[2]                   : 177522
  .cpu_load[3]                   : 177522
  .cpu_load[4]                   : 177522
cpu#1, 2393.874 MHz
  .nr_running                    : 4
  .load                          : 4096
  .cpu_load[0]                   : 181618
  .cpu_load[1]                   : 180850
  .cpu_load[2]                   : 180274
  .cpu_load[3]                   : 179938
  .cpu_load[4]                   : 179758

Which indicated the cpu_load computation was hosed, the 177522 value
indicates that there is one RT task runnable. Initially I thought the
old problem of calculating the cpu_load from a softirq had re-surfaced,
however looking at the code shows its being done from scheduler_tick().

[ we really should fix this RT/cfs interaction some day... ]

A few trace_printk()s later:

    sirq-timer/1-19    [001]   174.289744:     19: 50:S ==> [001]     0:140:R <idle>                            
          <idle>-0     [001]   174.290724: enqueue_task_rt: adding task: 19/sirq-timer/1 with load: 177522      
          <idle>-0     [001]   174.290725:      0:140:R   + [001]    19: 50:S sirq-timer/1                      
          <idle>-0     [001]   174.290730: scheduler_tick: current load: 177522                                 
          <idle>-0     [001]   174.290732: scheduler_tick: current: 0/swapper                                   
          <idle>-0     [001]   174.290736:      0:140:R ==> [001]    19: 50:R sirq-timer/1                      
    sirq-timer/1-19    [001]   174.290741: dequeue_task_rt: removing task: 19/sirq-timer/1 with load: 177522    
    sirq-timer/1-19    [001]   174.290743:     19: 50:S ==> [001]     0:140:R <idle>  

We see that we always raise the timer softirq before doing the load
calculation. Avoid this by re-ordering the scheduler_tick() call in
update_process_times() to occur before we deal with timers.

This lowers the load back to sanity and restores regular load-balancing
behaviour.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon: add GET_PARAM/INFO support for Z pipes
  drm/radeon/kms: add r100/r200 OQ support.
  drm: Fix sysfs device confusion.
  drm/radeon/kms: implement the bo busy ioctl properly.

* 'btrfs' of git://git.kernel.dk/linux-2.6-block:
  btrfs: fix inode rbtree corruption

As noted in 83d349f3 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask.  That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.

This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.

The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f962 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.

Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty.  But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.

See

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not.  In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.

So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.

Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy.  So
just warn if a caller gives us an empty mask, and ignore it.

This fixes a regression in 2.6.30.x, due to commit 4595f962 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

which causes a silent lock-up.  It only seems to happen on PPro, P2, P3
and Athlon XP cores.  Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's.  Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Needed for occlusion queries on rv530 chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.

The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Acked-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

This adds the relocation necessary for OQ support on the r100/r200
chipsets.
Signed-off-by: Dave Airlie <airlied@redhat.com>

The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.

Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The previous patch assumes the ioctl already existed, when
it actually didn't.

It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>

* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c-stu300: I2C STU300 stability updates
  i2c-omap: Enable workaround for Errata 1.153 based on
  i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
  i2c-omap: Fix I2C status ACK

- blk clk is enabled when an irq arrives. The clk should be enabled,
  but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
  has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
  downwards.
- Number of address send attempts before giving up is increased to 12
  from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.

The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
  ALSA: hda: add model for Intel DG45ID/DG45FC boards
  ALSA: hda: enable speaker output for Compaq 6530s/6531s

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix oopses with doubly mounted snapshots
  nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()

Fix some issues with the AFS documentation, found when testing AFS on ppc64:

- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/kms: teardown crtc correctly when fb is destroyed.
  drm/kms/radeon: cleanup combios TV table like DDX.
  drm/radeon/kms: memset the allocated framebuffer before using it.
  drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
  drm/radeon/kms: implement bo busy check + current domain
  drm/radeon/kms: cut down indirects in register accesses.
  drm/radeon/kms: Fix up vertical blank interrupt support.
  drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
  drm/edid: fixup detailed timings like the X server.
  drm/radeon/kms: Add specific rs690 authorized register table

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Update Microblaze defconfigs
  microblaze: Use klimit instead of _end for memory init
  microblaze: Enable ppoll syscall
  microblaze: Sane handling of missing timer/intc in device tree
  microblaze: use the generic ack_bad_irq implementation

Merge branch 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Make 'make html' work
  perf annotate: Fix segmentation fault
  perf_counter: Fix the PARISC build
  perf_counter: Check task on counter read IPI
  perf: Rename perf-examples.txt to examples.txt
  perf record: Fix typo in pid_synthesize_comm_event

The BIOS pin configs are in fact correct and shall not be overwritten.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.

The codec differences before/after patch are:

@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
   Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
     Conn = Digital, Color = White
     DefAssociation = 0x3, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x24: IN
+  Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
   Pin Default 0x41813021: [N/A] Line In at Ext Rear
     Conn = 1/8, Color = Blue
     DefAssociation = 0x2, Sequence = 0x1
-  Pin-ctls: 0x24: IN VREF_80
+  Pin-ctls: 0x40: OUT VREF_HIZ
   Unsolicited: tag=00, enabled=0
   Connection: 1
      0x24

Tests show that it won't impact (external) Mic recording.
Reported-by: "Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Bit spinlocks are not working on RT. Replace them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: Dave Airlie <airlied@redhat.com>

The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.
Signed-off-by: Dave Airlie <airlied@redhat.com>

LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  security: Fix prompt for LSM_MMAP_MIN_ADDR
  security: Make LSM_MMAP_MIN_ADDR default match its help text.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: use the right flag for get_vm_area()
  percpu, sparc64: fix sparse possible cpu map handling
  init: set nr_cpu_ids before setup_per_cpu_areas()

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mce: Don't initialize MCEs on unknown CPUs
  x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
  x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c
  x86, mce: therm_throt: Don't log redundant normality
  x86: Fix UV BAU destination subnode id