This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.

This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.

This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.

sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().

New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().

Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:

- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant

sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).

With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.

For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some cards are not able to send the data token in time, but
miss the time frame for some bits(!). So synchronize to the
start of the token.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

It is necessary to wait for bus power before sending
any commands.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Turn off the bus power at suspend.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some MMC commands result in the card becoming busy after
the response is received.  This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does.  However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.

The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.

The command sequence for open-ended multi-block write
with DMA is now:

	Issue write command CMD25
	Receive CC interrupt
	Data is sent
	Receive TC interrupt (DMA is done)
	Issue stop command CMD12
	Receive CC interrupt
	Card is busy
	Receive TC interrupt
	Card is now ready for next transfer
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Nicolas Pitre accepted to look after the mvsdio driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This supports MMC/SD/SDIO currently found on the Kirkwood 88F6281 and
88F6192 SoC controllers.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kmap_atomic':
drivers/mmc/host/tmio_mmc.h:147: error: implicit declaration of function 'kmap_atomic'
drivers/mmc/host/tmio_mmc.h:147: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:153: error: implicit declaration of function 'kunmap_atomic'
drivers/mmc/host/tmio_mmc.h:153: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Update the tmio_mmc code to call mmc_free_host() when
done using the private data. Without this fix the driver
frees memory and then keeps on using it as private data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Update the tmio_mmc code to use resource_size(). With this
patch applied the correct resource size is passed to ioremap().
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some cards are slower than the standard allows and need more
time to respond to a command. Max. observed number of bytes
was 12.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Allow the platform data structures to specify spi mode 3
(if there is a pullup on the clock line or the spi hardware
is not able to serve spi mode 0).
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Domain change of the sdhci development list.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

During mmc unsafe resume, choose the right voltage for the card after
powerup.

Although this has not seen to cause trouble, it's the wrong behaviour.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Most registers lose its state when the processor wakes up from sleep state.
Thus registers should be initialized, when the processor wakes up. However the
current hsmmc 'resume' function doesn't consider this issue and finally makes
deadlock. So this patch fixes this problem.
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Remove code that turns MMC1 power back on after it
has been powered off (when the voltage is 1.8V).

The offending code is not necessary because the
host controller bus voltage is initialized to
3V when probing or resuming.  Note that MMC powers up
with the highest voltage available (see mmc_power_up())
which will be 3V also.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Extended CSD is a MMC card register.  As increasingly interesting
fields are being added to Extended CSD, it is helpful to see its
value.  Note that SD cards do not have an Extended CSD
register, so it is MMC only.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Currently we are using an explicit udev rule to trigger loading of the
mmc-block module when an MMC or SD card is detected:

    SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block"

It makes much more sense for the mmc bus driver and the mmc-block module to
share MODALIAS information so that they are linked automatically.

There is no real information of use in the MMC system at the current time.
All devices inserted require us to load the mmc-block device.  Until such
time as useful parameters exist simply reflect the module linkage via
the module alias below:

	mmc:block
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

With a sufficiently new compiler and binutils, code which wasn't
previously generating .eh_frame sections has begun to.  Certain
architectures (powerpc, in this case) may generate unexpected relocation
formats in response to this, preventing modules from loading.

While the new relocation types should probably be handled, revert to the
previous behaviour with regards to generation of .eh_frame sections.

(This was reported against Fedora, which appears to be the only distro
doing any building against gcc-4.4 at present: RH bz#486545.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Alexandre Oliva <aoliva@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Revert the change to the orphan dates of Windows 95, DOS, compression.
Add a new orphan date for OS/2.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  ucc_geth: Fix oops when using fixed-link support
  dm9000: locking bugfix
  net: update dnet.c for bus_id removal
  dnet: DNET should depend on HAS_IOMEM
  dca: add missing copyright/license headers
  nl80211: Check that function pointer != NULL before using it
  sungem: missing net_device_ops
  be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
  be2net: replenish when posting to rx-queue is starved in out of mem conditions
  bas_gigaset: correctly allocate USB interrupt transfer buffer
  smsc911x: reset last known duplex and carrier on open
  sh_eth: Fix mistake of the address of SH7763
  sh_eth: Change handling of IRQ
  netns: oops in ip[6]_frag_reasm incrementing stats
  net: kfree(napi->skb) => kfree_skb
  net: fix sctp breakage
  ipv6: fix display of local and remote sit endpoints
  net: Document /proc/sys/net/core/netdev_budget
  tulip: fix crash on iface up with shirq debug
  virtio_net: Make virtio_net support carrier detection
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix crash with /proc/iomem
  sparc64: Reschedule KGDB capture to a software interrupt.
  sbus: Auto-load openprom module when device opened.

This patch fixes bug #12208:

  Bug-Entry       : http://bugzilla.kernel.org/show_bug.cgi?id=12208
  Subject         : uml is very slow on 2.6.28 host

This turned out to be not a scheduler regression, but an already
existing problem in ptrace being triggered by subtle scheduler
changes.

The problem is this:

 - task A is ptracing task B
 - task B stops on a trace event
 - task A is woken up and preempts task B
 - task A calls ptrace on task B, which does ptrace_check_attach()
 - this calls wait_task_inactive(), which sees that task B is still on the runq
 - task A goes to sleep for a jiffy
 - ...

Since UML does lots of the above sequences, those jiffies quickly add
up to make it slow as hell.

This patch solves this by not rescheduling in read_unlock() after
ptrace_stop() has woken up the tracer.

Thanks to Oleg Nesterov and Ingo Molnar for the feedback.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc:
  powerpc/mm: Fix Respect _PAGE_COHERENT on classic ppc32 SW TLB load machines