- 22 Sep, 2006 40 commits
-
-
Masahide NAKAMURA authored
Transformation user interface is not only for IPsec. Based on MIPL2 kernel patch. Signed-off-by:
Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Masahide NAKAMURA authored
For outbound transformation, bundle is checked whether it is suitable for current flow to be reused or not. In such IPv6 case as below, transformation may apply incorrect bundle for the flow instead of creating another bundle: - The policy selector has destination prefix length < 128 (Two or more addresses can be matched it) - Its bundle holds dst entry of default route whose prefix length < 128 (Previous traffic was used such route as next hop) - The policy and the bundle were used a transport mode state and this time flow address is not matched the bundled state. This issue is found by Mobile IPv6 usage to protect mobility signaling by IPsec, but it is not a Mobile IPv6 specific. This patch adds strict check to xfrm_bundle_ok() for each state mode and address when prefix length is less than 128. Signed-off-by:
-
Masahide NAKAMURA authored
With this patch transformation state is updated last used time for each sending. Xtime is used for it like other state lifetime expiration. Mobile IPv6 enabled nodes will want to know traffic status of each binding (e.g. judgement to request binding refresh by correspondent node, or to keep home/care-of nonce alive by mobile node). The last used timestamp is an important hint about it. Based on MIPL2 kernel patch. This patch was also written by: Henrik Petander <petander@tcs.hut.fi> Signed-off-by:
-
Noriaki TAKAMIYA authored
Care-of address is carried by state as a transformation option like IPsec encryption/authentication algorithm. Based on MIPL2 kernel patch. Signed-off-by:
Noriaki TAKAMIYA <takamiya@po.ntts.co.jp> Signed-off-by:
-
Masahide NAKAMURA authored
For originated outbound IPv6 packets which will fragment, ip6_append_data() should know length of extension headers before sending them and the length is carried by dst_entry. IPv6 IPsec headers fragment then transformation was designed to place all headers after fragment header. OTOH Mobile IPv6 extension headers do not fragment then it is a good idea to make dst_entry have non-fragment length to tell it to ip6_append_data(). Signed-off-by:
-
Masahide NAKAMURA authored
Outbound transformation replaces both source and destination address with state's end-point addresses at the same time when IPsec tunnel mode. It is also required to change them for Mobile IPv6 route optimization, but we should care about the following differences: - changing result is not end-point but care-of address - either source or destination is replaced for each state This hook is a common platform to change outbound address. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
On current kernel inbound transformation state is allowed transport and disallowed tunnel mode when mismatch is occurred between tempates and states. As the result of adding two more modes by Mobile IPv6, this function name is misleading. Inbound transformation can allow only transport mode when mismatch is occurred between template and secpath. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
XFRM_STATE_WILDRECV flag is introduced; the last resort state is set it and receives packet which is not route optimized but uses such extension headers i.e. Mobile IPv6 signaling (binding update and acknowledgement). A node enabled Mobile IPv6 adds the state. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
For Mobile IPv6 usage, routing header or destination options header is used and it doesn't require this comparison. It is checked only for IPsec template. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
Route optimization is used with routing header and destination options header for Mobile IPv6. At outbound it makes header space like IPsec transport. At inbound it does nothing because exhdrs.c functions have responsibility to update skbuff information for these headers. Signed-off-by:
-
Masahide NAKAMURA authored
On current kernel, ip6_find_1stfragopt() is used by IPv6 IPsec to find offset to be inserted header in outbound for transport mode. (BTW, no usage may be needed for IPv4 case.) Mobile IPv6 requires another logic for routing header and destination options header respectively. This patch is common platform for the offset and adopts it to IPsec. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
This is a support to search transformation states by its addresses by using source address list for Mobile IPv6 usage. To use it from user-space, it is also added a message type for source address as a xfrm state option. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
Support source address based searching. Mobile IPv6 will use it. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
XFRM_MAX_DEPTH is a limit of transformation states to be applied to the same flow. Two more extension headers are used by Mobile IPv6 transformation. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
It will be added two more transformation protocols (routing header and destination options header) for Mobile IPv6. xfrm_id_proto_match() can be handle zero as all, IPSEC_PROTO_ANY as all IPsec and otherwise as exact one. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
Put the helper to header for future use. Based on MIPL2 kernel patch. Signed-off-by:
-
Masahide NAKAMURA authored
Transformation mode is used as either IPsec transport or tunnel. It is required to add two more items, route optimization and inbound trigger for Mobile IPv6. Based on MIPL2 kernel patch. This patch was also written by: Ville Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by:
-
YOSHIFUJI Hideaki authored
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags into RT6_LOOKUP_F_xxx flags, and put them into ip6_route.h Signed-off-by:
-
YOSHIFUJI Hideaki authored
This is for developers only. Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
Ville Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Signed-off-by:
-
YOSHIFUJI Hideaki authored
Signed-off-by:
-
YOSHIFUJI Hideaki authored
Even on RTN_ROOT node, we need to process its subtree first. Fix NULL pointer dereference in fib6_locate(). Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Signed-off-by:
-
YOSHIFUJI Hideaki authored
Based on MIPL2 kernel patch. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Split up function for finding routes for redirects. Signed-off-by:
-
YOSHIFUJI Hideaki authored
Signed-off-by:
-
David S. Miller authored
Instead just cancel the nested attribute and return 0. Signed-off-by: -
Thomas Graf authored
Signed-off-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Vladislav Yasevich authored
The SCTP sysctl entries are displayed in milliseconds, but stored internally in jiffies. This results in multiple levels of msecs to jiffies conversion and as a result produces a truncation error. This patch makes things consistent in that we store and display defaults in milliseconds and only convert once for use by association. This patch also adds some sane min/max values so that we don't go off the deep end. Signed-off-by:
Vladislav Yasevich <vladislav.yasevich@hp.com> Signed-off-by:
Sridhar Samudrala <sri@us.ibm.com> Signed-off-by:
-
Patrick McHardy authored
- remove unused define - remove useless wrapper function - use new line for expression after condition Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Patrick McHardy authored
The matches are identical besides one looking for NEXTHDR_HOP, the other for NEXTHDR_DEST. Remove ip6t_dst.c and handle both in ip6t_hbh.c. Signed-off-by:
Patrick McHardy <kaber@trash,net> Signed-off-by:
-
Patrick McHardy authored
Shared match functions can use this to make runtime decisions basen on the used match. Signed-off-by:
-
