val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.

Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1

This patch fixes the above errors.

Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

* git://git.infradead.org/battery-2.6:
  pmu_battery: Fix battery full reporting

/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).

This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
  OMAP: DSS2: OMAPFB: fix crash when panel driver was not loaded
  OMAP: DSS2: Reject scaling settings when they cannot be supported
  OMAP: DSS2: Make check-delay-loops consistent
  OMAP: DSS2: OMAPFB: fix omapfb_free_fbmem()
  video/omap: add __init/__exit macros to drivers/video/omap/lcd_htcherald.c
  OMAP: DSS2: Fix compile warning
  MAINTAINERS: Combine DSS2 and OMAPFB2 into one entry
  MAINTAINERS: change omapfb maintainer
  OMAP: OMAPFB: add dummy release function for omapdss
  OMAP: OMAPFB: fix clk_get for RFBI
  OMAP: DSS2: RFBI: convert to new kfifo API
  OMAP: DSS2: Fix crash when panel doesn't define enable_te()
  OMAP: DSS2: Collect interrupt statistics
  OMAP: DSS2: DSI: print debug DCS cmd in hex
  OMAP: DSS2: DSI: fix VC channels in send_short and send_null

There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs.  Now XFS needs this as well.  Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Maybe this will stop people emailing me about it.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry link resume if necessary
  ata_piix: enable 32bit PIO on SATA piix
  sata_promise: don't classify overruns as HSM errors

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
  ARM: Fix wrong dmb
  ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
  ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
  ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
  ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
  ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
  ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
  ARM: 5867/1: Update U300 defconfig
  ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
  [ARM] pxa: fix strange characters in zaurus gpio .desc
  ARM: add missing recvmmsg syscall number
  [ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
  [ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
  [ARM] pxa: enable L2 if present in XSC3
  [ARM] pxa: do not enable L2 after MMU is enabled

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (22 commits)
  MIPS: Ignore vmlinux.*
  MIPS: Move vmlinux.ecoff to arch/mips/boot
  MIPS: cpumask_of_node() should handle -1 as a node
  MIPS: Octeon: Use non-overflowing arithmetic in sched_clock
  MIPS: Malta, PowerTV: Remove unnecessary "Linux started"
  MIPS: BCM63xx: Remove duplicate CONFIG_CMDLINE.
  MIPS: AR7: Remove unused prom_getchar()
  MIPS: PowerTV: Remove extra r4k_clockevent_init() call
  MIPS: Cobalt use strlcat() for the command line arguments
  MIPS: Octeon: Add sched_clock() to csrc-octeon.c
  MIPS: TXx9: Cleanup builtin-cmdline processing
  MIPS: PowerTV: simplify prom_init_cmdline() and merge into prom_init()
  MIPS: PowerTV: Remove unused platform_die()
  MIPS: PowerTV: Remove mips_machine_halt()
  MIPS: PowerTV: Remove unused ptv_memsize
  MIPS: PowerTV: Remove unused prom_getcmdline()
  MIPS: AR7: Remove kgdb_enabled
  MIPS: Alchemy: Correct code taking the size of a pointer
  MIPS: BCM63xx: Fix whitespace damaged board_bcm963xx.c
  MIPS: VR41xx: Use strlcat() for the command line arguments
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix ALC861-VD capture source mixer
  ALSA: ac97: add AC97 STMicroelectronics' codecs
  ALSA: ac97: Add Dell Dimension 2400 to Headphone/Line Jack Sense blacklist
  ASoC: Fix WM8350 DSP mode B configuration
  sbawe: fix memory detection part 2
  sound: oss: off by one bug
  ALSA: usb-audio - Avoid Oops after disconnect
  ALSA: test off by one in setsamplerate()
  ALSA: atiixp: Specify codec for Foxconn RC4107MA-RS2

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
  sky2: Fix oops in sky2_xmit_frame() after TX timeout
  Documentation/3c509: document ethtool support
  af_packet: Don't use skb after dev_queue_xmit()
  vxge: use pci_dma_mapping_error to test return value
  netfilter: ebtables: enforce CAP_NET_ADMIN
  e1000e: fix and commonize code for setting the receive address registers
  e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
  e1000e: perform 10/100 adaptive IFS only on parts that support it
  e1000e: don't accumulate PHY statistics on PHY read failure
  e1000e: call pci_save_state() after pci_restore_state()
  netxen: update version to 4.0.72
  netxen: fix set mac addr
  netxen: fix smatch warning
  netxen: fix tx ring memory leak
  tcp: update the netstamp_needed counter when cloning sockets
  TI DaVinci EMAC: Handle emac module clock correctly.
  dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
  ixgbe: Fix compiler warning about variable being used uninitialized
  netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
  mv643xx_eth: don't include cache padding in rx desc buffer size
  ...

Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c

Fix compilation breakage of all m68knommu targets:

  CC      arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
                 from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy

This is broken in linux-2.6.33-rc3.

Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.

A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().

Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure.  Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit 871af121 enabled 32bit PIO for
PATA piix but didn't for SATA.  There's no reason not to use 32bit PIO
on SATA piix.  Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.

Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.

This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.

This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for.  Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/795/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It moves to the same directory as the boot files in other formats.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:

# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65

Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:

# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/831/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With typical mult and shift values, the calculation for Octeon's sched_clock
overflows when using 64-bit arithmetic.  Use 128-bit calculations instead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/849/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/813/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Builtin cmdline is copied by arch_mem_init().
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/812/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/811/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

A call to r4k_clocksource_init() was added to plat_time_init(), but
when init_mips_clock_source() calls the same function, boot fails in
clockevents_register_device(). This patch removes the extraneous call.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Patchwork: http://patchwork.linux-mips.org/patch/803/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Tested with CoLo v1.22
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/807/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With the advent of function graph tracing on MIPS, Octeon needs a high
precision sched_clock() implementation.  Without it, most timing
numbers are reported as 0.000.

This new sched_clock just uses the 64-bit cycle counter appropriately
scaled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/805/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Since commit 898d357b5262f9e26bc2418e01f8676e80d9867e (lmo) /
6acc7d48 (kernel.org) ("Fix and enhance
built-in kernel command line") arcs_cmdline[] does not contain built-in
command line.  The commit introduce CONFIG_CMDLINE_BOOL and
CONFIG_CMDLINE_OVERRIDE to control built-in command line, and now we can
use them instead of platform-specific built-in command line processing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Patchwork: http://patchwork.linux-mips.org/patch/802/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/801/Reviewed-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/800/Reviewed-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>