- 29 Nov, 2009 1 commit
-
-
Andrei Pelinescu-Onciul authored
When retransmitting due to T3 timeout, retransmit all the in-flight chunks for the corresponding transport/path, including chunks sent less then 1 rto ago. This is the correct behaviour according to rfc4960 section 6.3.3 E3 and "Note: Any DATA chunks that were sent to the address for which the T3-rtx timer expired but did not fit in one MTU (rule E3 above) should be marked for retransmission and sent as soon as cwnd allows (normally, when a SACK arrives). ". This fixes problems when more then one path is present and the T3 retransmission of the first chunk that timeouts stops the T3 timer for the initial active path, leaving all the other in-flight chunks waiting forever or until a new chunk is transmitted on the same path and timeouts (and this will happen only if the cwnd allows sending new chunks, but since cwnd was dropped to MTU by the timeout => it will wait until the first heartbeat). Example: 10 packets in flight, sent at 0.1 s intervals on the primary path. The primary path is down and the first packet timeouts. The first packet is retransmitted on another path, the T3 timer for the primary path is stopped and cwnd is set to MTU. All the other 9 in-flight packets will not be retransmitted (unless more new packets are sent on the primary path which depend on cwnd allowing it, and even in this case the 9 packets will be retransmitted only after a new packet timeouts which even in the best case would be more then RTO). This commit reverts d0ce9291 and also removes the now unused transport->last_rto, introduced in b6157d8e. p.s The problem is not only when multiple paths are there. It can happen in a single homed environment. If the application stops sending data, it possible to have a hung association. Signed-off-by: Andrei Pelinescu-Onciul <andrei@iptel.org> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 24 Nov, 2009 1 commit
-
-
Eric Dumazet authored
When multi queue compatable names are used by pktgen (eg eth0@0), we currently cannot unload a NIC driver if one of its device is currently in use. Allow pktgen_find_dev() to find pktgen devices by their suffix (netdev name) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 23 Nov, 2009 12 commits
-
-
Patrick McHardy authored
gso_max_size must be set based on the value of the underlying device to support devices not using the full 64k. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Johannes Berg authored
The /dev/rfkill ops don't refer to the module, so it is possible to unload the module while file descriptors are open. Fix this oversight. Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Copied from original one-line patch here: http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Antti Kaijanmäki authored
Fix soft-lockup in hso.c which is triggered on SMP machine when modem is removed while file descriptor(s) under /dev are still open: old version called kref_put() too early which resulted in destroying hso_serial and hso_device objects which were still used later on. Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Antti Kaijanmäki authored
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Commit e6fce5b9 (pktgen: multiqueue etc.) tried to relax the pktgen restriction of one device per kernel thread, adding a '@' tag to device names. Problem is we dont perform check on full pktgen device name. This allows adding many time same 'device' to pktgen thread pgset "add_device eth0@0" one session later : pgset "add_device eth0@0" (This doesnt find previous device) This consumes ~1.5 MBytes of vmalloc memory per round and also triggers this warning : [ 673.186380] proc_dir_entry 'pktgen/eth0@0' already registered [ 673.186383] Modules linked in: pktgen ixgbe ehci_hcd psmouse mdio mousedev evdev [last unloaded: pktgen] [ 673.186406] Pid: 6219, comm: bash Tainted: G W 2.6.32-rc7-03302-g41cec6f1-dirty #16 [ 673.186410] Call Trace: [ 673.186417] [<ffffffff8104a29b>] warn_slowpath_common+0x7b/0xc0 [ 673.186422] [<ffffffff8104a341>] warn_slowpath_fmt+0x41/0x50 [ 673.186426] [<ffffffff8114e789>] proc_register+0x109/0x210 [ 673.186433] [<ffffffff8100bf2e>] ? apic_timer_interrupt+0xe/0x20 [ 673.186438] [<ffffffff8114e905>] proc_create_data+0x75/0xd0 [ 673.186444] [<ffffffffa006ad38>] pktgen_thread_write+0x568/0x640 [pktgen] [ 673.186449] [<ffffffffa006a7d0>] ? pktgen_thread_write+0x0/0x640 [pktgen] [ 673.186453] [<ffffffff81149144>] proc_reg_write+0x84/0xc0 [ 673.186458] [<ffffffff810f5a58>] vfs_write+0xb8/0x180 [ 673.186463] [<ffffffff810f5c11>] sys_write+0x51/0x90 [ 673.186468] [<ffffffff8100b51b>] system_call_fastpath+0x16/0x1b [ 673.186470] ---[ end trace ccbb991b0a8d994d ]--- Solution to this problem is to use a odevname field (includes @ tag and suffix), instead of using netdevice name. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
If the external timer cannot be used the driver will continue to work without mitigation. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
-
Patrick McHardy authored
Commit acc738fe (netfilter: xtables: avoid pointer to self) introduced an invalid return value in limit_mt_check(). Signed-off-by: Patrick McHardy <kaber@trash.net>
-
Alexander Beregalov authored
Andreas Lohre reported that the driver crashes when trying to register_netdev(), he sugessted to move dev->netdev_ops initialization before calling register_netdev(), it worked for him. Reported-by: Andreas Lohre <alohre@gmail.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 21 Nov, 2009 3 commits
-
-
Narender Kumar authored
o Along with netdev->perm_addr, mac address will be maintained in device private structure. o Device limitation: We need to set mac address when ever interface comes up. In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address. But bonding driver set netdev->dev_addr field to its original value, after enslaving interfaces. When ever active slave changes, it swap dev_addr of inactive slave with active. Yet it doesn't notify driver about change in netdev->dev_addr. As netxen driver need to set mac addr when ever interface comes up, it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Narender Kumar authored
Kernel crashes, if promisc mode set without disabling rx queue. Before changing mode in NX2031 chip, wait till rx queue drains. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Kumar Salecha authored
Avoid resetting memory during initialization, skip this memory block during driver probe. Signed-off-by: Amit Kumar Salecha <amit@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 20 Nov, 2009 11 commits
-
-
chaithrika@ti.com authored
Use BIT for macro definitions wherever possible, remove unused and redundant macros. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David J. Choi authored
Summary of Changes: -Fix to receive multicast packets by setting the corresponding hardware bit during initialization. -Fix to re-enable the interface [by interface up command(ifup)] while the interface is down. -Fix to be able to down the interface by passing the last parameter correctly to request_irq(). -Remove to read 4 extra bytes from the receiving queue after reading a packet, even though it does not cause a predictable issue now. -Remove occurrences of transmission done interrupt in order to tx throughput enhancement. -Enable IP checksum for packet receiving by setting the corresponding hardware bit during initialization. -Relocate ks_enable_int()/ks_disable_int() in order not to declare those functions at the beginning of the file. -Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in order to give more meaningful names and relocate them not declaire those functions at the beginning of the file. Signed-off-by: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Geert Uytterhoeven authored
When building for Sun 3: drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent' drivers/built-in.o: In function `ethoc_probe': drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent' drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent' Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
When configuring the OEM bits in the PHY on 82577/82578, do not restart autonegotiation if the firmware is blocking it (e.g. when an IDE-R session is active) because the link must not go down. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
A workaround for pre-release versions of 82577 is causing link issues on some switches. The workaround is no longer needed on production parts so remove it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
When changing MTU, save it off prior to resetting otherwise the flow control thresholds may be miscalculated. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
On some devices (e.g. 82578) not having a Tx timeout factor when linked at 100Mbps can cause false reports of hardware hangs on busy hubs. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
When flow control (pause) parameters were changed via ethtool (i.e. enabled or disabled), the newly calculated thresholds were not being written to the device for non-fiber media. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
Remove unnecessary workaround that mistakenly does not perform a page select operation for PHY registers 29 and 30 (assuming these are the PHY debug port address and data registers) on 82578 which can cause reads of the Transmit with No Carrier Sense statistics register on page 778 to be read from an incorrect page. Also error out if the page select operation fails. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bruce Allan authored
Commit 3ec2a2b8 broke Tx/Rx when using jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged once the high water mark was reached preventing normal packet traffic). This patch reverts the breakage and sets appropriate high and low water marks of the Rx FIFO for 82577/82578 which require a workaround due to a flow control issue in hardware. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jaswinder Singh Rajput authored
tc is required by CONFIG_IXGBE_DCB. This also fixes compilation warning: drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’: drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’ Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 19 Nov, 2009 10 commits
-
-
Patrick McHardy authored
[ 171.925285] BUG: sleeping function called from invalid context at kernel/mutex.c:280 [ 171.925296] in_atomic(): 1, irqs_disabled(): 0, pid: 671, name: grep [ 171.925306] 2 locks held by grep/671: [ 171.925312] #0: (&p->lock){+.+.+.}, at: [<c10b8acd>] seq_read+0x25/0x36c [ 171.925340] #1: (rcu_read_lock){.+.+..}, at: [<c1391dac>] seq_start+0x0/0x44 [ 171.925372] Pid: 671, comm: grep Not tainted 2.6.31.6-4-netbook #3 [ 171.925380] Call Trace: [ 171.925398] [<c105104e>] ? __debug_show_held_locks+0x1e/0x20 [ 171.925414] [<c10264ac>] __might_sleep+0xfb/0x102 [ 171.925430] [<c1461521>] mutex_lock_nested+0x1c/0x2ad [ 171.925444] [<c1391c9e>] seq_show+0x74/0x127 [ 171.925456] [<c10b8c5c>] seq_read+0x1b4/0x36c [ 171.925469] [<c10b8aa8>] ? seq_read+0x0/0x36c [ 171.925483] [<c10d5c8e>] proc_reg_read+0x60/0x74 [ 171.925496] [<c10d5c2e>] ? proc_reg_read+0x0/0x74 [ 171.925510] [<c10a4468>] vfs_read+0x87/0x110 [ 171.925523] [<c10a458a>] sys_read+0x3b/0x60 [ 171.925538] [<c1002a49>] syscall_call+0x7/0xb Fix it by replacing RCU with nf_log_mutex. Reported-by: "Yin, Kangkai" <kangkai.yin@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Patrick McHardy authored
Return a negative error value. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
veth_get_stats() can be called in parallel on several cpus. It's better to not reset dev->stats as it could give wrong result on one cpu. Use temporary variables, then store the final results. Also, we should loop on every possible cpus, not only online cpus, or cpu hotplug can suddenly give wrong veth stats. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
ieee802154_fake_xmit() should free skbs since it returns NETDEV_TX_OK Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Johannes Berg authored
When mac80211 resumes, it currently first sets suspended to false so the driver can start doing things and we can receive frames. However, if we actually receive frames then it can end up starting some work which adds timers and then later runs into a BUG_ON in the timer code because it tries add_timer() on a pending timer. Fix this by keeping track of the resuming process by introducing a new variable 'resuming' which gets set to true early on instead of setting 'suspended' to false, and allow queueing work but not receiving frames while resuming. Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreqLinus Torvalds authored
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ] Fix stale cpufreq_cpu_governor pointer [CPUFREQ] Resolve time unit thinko in ondemand/conservative govs [CPUFREQ] speedstep-ich: fix error caused by 394122ab [CPUFREQ] Fix use after free on governor restore [CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message [CPUFREQ] powernow-k8: Fix test in get_transition_latency() [CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs
-
Linus Torvalds authored
Doing the strcmp return value as signed char __res = *cs - *ct; is wrong for two reasons. The subtraction can overflow because __res doesn't use a type big enough. Moreover the compared bytes should be interpreted as unsigned char as specified by POSIX. The same problem is fixed in strncmp. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Michael Buesch <mb@bu3sch.de> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6Linus Torvalds authored
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6: agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()
-
Linus Torvalds authored
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: ima: replace GFP_KERNEL with GFP_NOFS
-
David Woodhouse authored
We should set this before calling agp_add_bridge() so that it's done before we map the scratch page too. This should probably fix the regression reported as k.o. bug #14627. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
- 18 Nov, 2009 2 commits
-
-
Linus Torvalds authored
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: OMAP: cs should be positive in gpmc_cs_free() omap: fix unlikely(x) < y omap3: clock: Fixed dpll3_m2x2 rate calculation omap3: clock: Fix the DPLL freqsel computations omap: Fix keymap for zoom2 according to matrix keypad framwork
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ASoC: tlv320aic23 fix rate selection ASoC: OMAP3 Pandora: update for TWL4030 codec changes ASoC: Modifying the license string GPLv2 for OMAP3 EVM ALSA: hda - Fix quirk for VAIO type G ALSA: usb - Quirk to disable master volume control in PCM2702
-