Currently the recv ring low water mark is 1/4 the depth.  Performance
measurements show that this limits iWARP throughput by flow controlling
the rds-stress senders.  Setting it to 1/2 seems to max the T3
performance.  I tried even higher levels but that didn't help and it
started to increase the rds thread cpu utilization.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the merging of mISDN, state which files refer only to the
old isdn4linux subsystem. Also add a few missing files and sort
alphabetically.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neither the lm90 driver nor the lm87 driver do support interrupts, so
there is no point in specifying one when declaring the devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aligning register offset translation table imporves performance
on rx side.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable multiple rx rings for older NX2031 chip, firmware 3.4.336
or newer supports this feature.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace superfluous wrapper functions with two macros:

NXWR32 replaces netxen_nic_reg_write, netxen_nic_write_w0,
netxen_nic_read_w1, netxen_crb_writelit_adapter.

NXRD32 replaces netxen_nic_reg_read, netxen_nic_read_w0,
netxen_nic_read_w1.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o remove unnecessary length parameter since register access
  width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
  functions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reduces netxen_adapter footprint when rss (msi-x) is disabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for asynchronous events from firmware,
received over one of the rx rings.

Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed duplicate firmware handshake, defer it until first
port (interface) is brought up.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o move tx stuff into nx_host_tx_ring structure, this will
  help managing multiple tx rings in future.
o sanitize some variable names
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rearrange members to align them at right offset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o remove unused structure defs.
o remove unnecessary includes.
o replace enums with specific #defines.
o reduce footprint of stats structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'core/softlockup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: make DETECT_HUNG_TASK default depend on DETECT_SOFTLOCKUP
  softlockup: move 'one' to the softlockup section in sysctl.c
  softlockup: ensure the task has been switched out once
  softlockup: remove timestamp checking from hung_task
  softlockup: convert read_lock in hung_task to rcu_read_lock
  softlockup: check all tasks in hung_task
  softlockup: remove unused definition for spawn_softlockup_task
  softlockup: fix potential race in hung_task when resetting timeout
  softlockup: fix to allow compiling with !DETECT_HUNG_TASK
  softlockup: decouple hung tasks check from softlockup detection

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
  branch tracer: Fix for enabling branch profiling makes sparse unusable
  ftrace: Correct a text align for event format output
  Update /debug/tracing/README
  tracing/ftrace: alloc the started cpumask for the trace file
  tracing, x86: remove duplicated #include
  ftrace: Add check of sched_stopped for probe_sched_wakeup
  function-graph: add proper initialization for init task
  tracing/ftrace: fix missing include string.h
  tracing: fix incorrect return type of ns2usecs()
  tracing: remove CALLER_ADDR2 from wakeup tracer
  blktrace: fix pdu_len when tracing packet command requests
  blktrace: small cleanup in blk_msg_write()
  blktrace: NUL-terminate user space messages
  tracing: move scripts/trace/power.pl to scripts/tracing/power.pl

* 'irq/threaded' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: fix devres.o build for GENERIC_HARDIRQS=n
  genirq: provide old request_irq() for CONFIG_GENERIC_HARDIRQ=n
  genirq: threaded irq handlers review fixups
  genirq: add support for threaded interrupts to devres
  genirq: add threaded interrupt handler support

Commit c2ec175c ("mm: page_mkwrite
change prototype to match fault") exposed a bug in the NFS
implementation of page_mkwrite.  We should be returning 0 on success...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: pci_slot: grab refcount on slot's bus
  PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
  PCI: allow PCI core hotplug to remove PCI root bus
  PCI: Fix oops in pci_vpd_truncate
  PCI: don't corrupt enable_cnt when doing manual resource alignment
  PCI: annotate pci_rescan_bus as __ref, not __devinit
  PCI-IOV: fix missing kernel-doc
  PCI: Setup disabled bridges even if buses are added
  PCI: SR-IOV quirk for Intel 82576 NIC

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  loop: mutex already unlocked in loop_clr_fd()
  cfq-iosched: don't let idling interfere with plugging
  block: remove unused REQ_UNPLUG
  cfq-iosched: kill two unused cfqq flags
  cfq-iosched: change dispatch logic to deal with single requests at the time
  mflash: initial support
  cciss: change to discover first memory BAR
  cciss: kernel scan thread for MSA2012
  cciss: fix residual count for block pc requests
  block: fix inconsistency in I/O stat accounting code
  block: elevator quiescing helpers

The code that enables branch tracing for all (non-constant) branches
plays games with the preprocessor and #define's the C 'if ()' construct
to do tracing.

That's all fine, but it fails for some unusual but valid C code that is
sometimes used in macros, notably by the intel-iommu code:

	if (i=drhd->iommu, drhd->ignored) ..

because now the preprocessor complains about multiple arguments to the
'if' macro.

So make the macro expansion of this particularly horrid trick use
varargs, and handle the case of comma-expressions in if-statements.  Use
another macro to do it cleanly in just one place.

This replaces a patch by David (and acked by Steven) that did this all
inside that one already-too-horrid macro.
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6:
  ASoC: TWL4030: Compillation error fix

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (36 commits)
  ALSA: hda - Add VREF powerdown sequence for another board
  ALSA: oss - volume control for CSWITCH and CROUTE
  ALSA: hda - add missing comma in ad1884_slave_vols
  sound: usb-audio: allow period sizes less than 1 ms
  sound: usb-audio: save data packet interval in audioformat structure
  sound: usb-audio: remove check_hw_params_convention()
  sound: usb-audio: show sample format width in proc file
  ASoC: fsl_dma: Pass the proper device for dma mapping routines
  ASoC: Fix null dereference in ak4535_remove()
  ALSA: hda - enable SPDIF output for Intel DX58SO board
  ALSA: snd-atmel-abdac: increase periods_min to 6 instead of 4
  ALSA: snd-atmel-abdac: replace bus_id with dev_name()
  ALSA: snd-atmel-ac97c: replace bus_id with dev_name()
  ALSA: snd-atmel-ac97c: cleanup registers when removing driver
  ALSA: snd-atmel-ac97c: do a proper reset of the external codec
  ALSA: snd-atmel-ac97c: enable interrupts to catch events for error reporting
  ALSA: snd-atmel-ac97c: set correct size for buffer hardware parameter
  ALSA: snd-atmel-ac97c: do not overwrite OCA and ICA when assigning channels
  ALSA: snd-atmel-ac97c: remove dead break statements after return in switch case
  ALSA: snd-atmel-ac97c: cleanup register definitions
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_mv: shorten register names
  sata_mv: workaround errata SATA#13
  sata_mv: cosmetic renames
  sata_mv: workaround errata SATA#26
  sata_mv: workaround errata PCI#7
  sata_mv: replace 0x1f with ATA_PIO4 (v2)
  sata_mv: fix irq mask races
  sata_mv: revert SoC irq breakage
  libata: ahci enclosure management bios workaround
  ata: Add TRIM infrastructure
  ata_piix: VGN-BX297XP wants the controller power up on suspend
  libata: Remove some redundant casts from pata_octeon_cf.c
  pata_artop: typo

* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c: imx: Make disable_delay a per-device variable
  i2c: xtensa s6000 i2c driver
  powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
  i2c: i2c-mpc: make I2C bus speed configurable
  i2c: i2c-mpc: use dev based printout function
  i2c: i2c-mpc: various coding style fixes
  i2c: imx: Add missing request_mem_region in probe()
  i2c: i2c-s3c2410: Initialise Samsung I2C controller early
  i2c-s3c2410: Simplify bus frequency calculation
  i2c-s3c2410: sda_delay should be in ns, not clock ticks
  i2c: iMX/MXC support

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: Add Asus ATK0110 support
  hwmon: (lm95241) Convert to new-style i2c driver

PCI parallel port devices can IRQ share so we should stop them hogging
the line and making a mess on modern PC systems.  We know the sharing
side works as the PCMCIA driver has shared the parallel port IRQ for
some time.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Here are some cleanups, mainly removing unused variables and silly
declarations.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Depend on KGDB_SERIAL_CONSOLE being set to N rather than !Y, since it can
be built as a module.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Both software emulated and hardware based CTS and RTS are enabled in
serial driver.

The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device.  In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

(akpm: queued pending confirmation of the new major number)

[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is a low density serial port so needs a real major/minor
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Avoid using port->tty where possible (makes refcount fixing easier
later).

Remove unused code (the ioctl path is not used if the device has
mget/mset functions)

Remove various un-needed typecasts and long names so it could read it to
do the changes.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tty_driver_kref_get() should be static inline and not extern inline
(the latter even changed it's semantics in gcc >= 4.3).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There's a possible deadlock in generic_file_splice_write(),
splice_from_pipe() and ocfs2_file_splice_write():

 - task A calls generic_file_splice_write()
 - this calls inode_double_lock(), which locks i_mutex on both
   pipe->inode and target inode
 - ordering depends on inode pointers, can happen that pipe->inode is
   locked first
 - __splice_from_pipe() needs more data, calls pipe_wait()
 - this releases lock on pipe->inode, goes to interruptible sleep
 - task B calls generic_file_splice_write(), similarly to the first
 - this locks pipe->inode, then tries to lock inode, but that is
   already held by task A
 - task A is interrupted, it tries to lock pipe->inode, but fails, as
   it is already held by task B
 - ABBA deadlock

Fix this by explicitly ordering locks: the outer lock must be on
target inode and the inner lock (which is later unlocked and relocked)
must be on pipe->inode.  This is OK, pipe inodes and target inodes
form two nonoverlapping sets, generic_file_splice_write() and friends
are not called with a target which is a pipe.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>